src/soc/intel/alderlake/Kconfig

config SOC_INTEL_ALDERLAKE
	bool
	help
	  Intel Alderlake support. Mainboards should specify the PCH
	  type using the `SOC_INTEL_ALDERLAKE_PCH_*` options instead
	  of selecting this option directly.

config SOC_INTEL_RAPTORLAKE
	bool
	select X86_INIT_NEED_1_SIPI
	help
	 Intel Raptorlake support. Mainboards using RPL should select
	 SOC_INTEL_RAPTORLAKE and SOC_INTEL_ALDERLAKE_PCH_* together.

config SOC_INTEL_ALDERLAKE_PCH_M
	bool
	select SOC_INTEL_ALDERLAKE
	help
	  Choose this option if your mainboard has a PCH-M chipset.

config SOC_INTEL_ALDERLAKE_PCH_N
	bool
	select SOC_INTEL_ALDERLAKE
	select MICROCODE_BLOB_UNDISCLOSED
	help
	  Choose this option if your mainboard has a PCH-N chipset.

config SOC_INTEL_ALDERLAKE_PCH_P
	bool
	select SOC_INTEL_ALDERLAKE
	select HAVE_INTEL_FSP_REPO
	select PLATFORM_USES_FSP2_3
	help
	  Choose this option if your mainboard has a PCH-P chipset.

config SOC_INTEL_ALDERLAKE_PCH_S
	bool
	select SOC_INTEL_ALDERLAKE
	select HAVE_INTEL_FSP_REPO
	select PLATFORM_USES_FSP2_3
	help
	  Choose this option if your mainboard has a PCH-S chipset.

if SOC_INTEL_ALDERLAKE

config CPU_SPECIFIC_OPTIONS
	def_bool y
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select ACPI_ADL_IPU_ES_SUPPORT
	select ARCH_X86
	select BOOT_DEVICE_SUPPORTS_WRITES
	select CACHE_MRC_SETTINGS
	select CPU_INTEL_COMMON
	select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
	select CPU_SUPPORTS_INTEL_TME
	select CPU_SUPPORTS_PM_TIMER_EMULATION
	select DEFAULT_SOFTWARE_CONNECTION_MANAGER if MAINBOARD_HAS_CHROMEOS
	select DISPLAY_FSP_VERSION_INFO
	select DRIVERS_USB_ACPI
	select EDK2_CPU_TIMER_LIB if PAYLOAD_EDK2
	select FSP_COMPRESS_FSP_S_LZ4
	select FAST_SPI_SUPPORTS_EXT_BIOS_WINDOW
	select FSP_M_XIP
	select FSP_STATUS_GLOBAL_RESET_REQUIRED_3
	select FSP_USES_CB_DEBUG_EVENT_HANDLER
	select FSPS_HAS_ARCH_UPD
	select GENERIC_GPIO_LIB
	select HAVE_DEBUG_RAM_SETUP
	select HAVE_FSP_GOP
	select HAVE_HYPERTHREADING
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select HAVE_SMI_HANDLER
	select IDT_IN_EVERY_STAGE
	select INTEL_GMA_ACPI
	select INTEL_GMA_ADD_VBT if RUN_FSP_GOP
	select INTEL_GMA_OPREGION_2_1
	select INTEL_TXT_LIB
	select MRC_SETTINGS_PROTECT
	select PARALLEL_MP_AP_WORK
	select PLATFORM_USES_FSP2_2
	select PMC_GLOBAL_RESET_ENABLE_LOCK
	select SOC_INTEL_COMMON
	select CPU_INTEL_COMMON_VOLTAGE
	select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE
	select SOC_INTEL_COMMON_BLOCK
	select SOC_INTEL_COMMON_BLOCK_ACPI
	select SOC_INTEL_COMMON_BLOCK_ACPI_CPPC
	select SOC_INTEL_COMMON_BLOCK_ACPI_CPU_HYBRID
	select SOC_INTEL_COMMON_BLOCK_ACPI_GPIO
	select SOC_INTEL_COMMON_BLOCK_ACPI_LPIT
	select SOC_INTEL_COMMON_BLOCK_ACPI_PEP
	select SOC_INTEL_COMMON_BLOCK_ACPI_PEP_LPM_REQ
	select SOC_INTEL_COMMON_BLOCK_CAR
	select SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG
	select SOC_INTEL_COMMON_BLOCK_CNVI
	select SOC_INTEL_COMMON_BLOCK_CPU
	select SOC_INTEL_COMMON_BLOCK_CPU_MPINIT
	select SOC_INTEL_COMMON_BLOCK_CPU_SMMRELOCATE
	select SOC_INTEL_COMMON_BLOCK_DTT
	select SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT
	select SOC_INTEL_COMMON_BLOCK_GPIO_LOCK_USING_SBI
	select SOC_INTEL_COMMON_BLOCK_GSPI_VERSION_2
	select SOC_INTEL_COMMON_BLOCK_SCS if SOC_INTEL_ALDERLAKE_PCH_N
	select SOC_INTEL_COMMON_BLOCK_HDA
	select SOC_INTEL_COMMON_BLOCK_HECI1_DISABLE_USING_PMC_IPC
	select SOC_INTEL_COMMON_BLOCK_IPU if !SOC_INTEL_ALDERLAKE_PCH_S
	select SOC_INTEL_COMMON_BLOCK_IRQ
	select SOC_INTEL_COMMON_BLOCK_MEMINIT
	select SOC_INTEL_COMMON_BLOCK_PCIE_RTD3
	select SOC_INTEL_COMMON_BLOCK_PMC_EPOC
	select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT
	select SOC_INTEL_COMMON_BLOCK_SA
	select SOC_INTEL_COMMON_BLOCK_SMM
	select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP
	select SOC_INTEL_COMMON_BLOCK_THERMAL_BEHIND_PMC
	select SOC_INTEL_COMMON_BLOCK_XHCI
	select SOC_INTEL_COMMON_BLOCK_XHCI_ELOG
	select SOC_INTEL_COMMON_BASECODE
	select SOC_INTEL_COMMON_FSP_RESET
	select SOC_INTEL_COMMON_PCH_CLIENT
	select SOC_INTEL_COMMON_RESET
	select SOC_INTEL_CSE_SEND_EOP_LATE
	select SOC_INTEL_CSE_SET_EOP
	select SOC_INTEL_MEM_MAPPED_PM_CONFIGURATION
	select HAVE_INTEL_COMPLIANCE_TEST_MODE
	select SSE2
	select SUPPORT_CPU_UCODE_IN_CBFS
	select TSC_MONOTONIC_TIMER
	select UDELAY_TSC
	select UDK_202005_BINDING
	select VBOOT_LIB

config SOC_INTEL_ALDERLAKE_TCSS_USB4_SUPPORT
	bool
	default y if !SOC_INTEL_ALDERLAKE_PCH_S
	default n if SOC_INTEL_ALDERLAKE_PCH_S
	select SOC_INTEL_COMMON_BLOCK_TCSS
	select SOC_INTEL_COMMON_BLOCK_USB4
	select SOC_INTEL_COMMON_BLOCK_USB4_PCIE
	select SOC_INTEL_COMMON_BLOCK_USB4_XHCI

config ALDERLAKE_CONFIGURE_DESCRIPTOR
	bool
	help
	  Select this if the descriptor needs to be updated at runtime. This
	  can only be done if the descriptor region is writable, and should only
	  be used as a temporary workaround.

config ALDERLAKE_CAR_ENHANCED_NEM
	bool
	default y if !INTEL_CAR_NEM
	select INTEL_CAR_NEM_ENHANCED
	select CAR_HAS_SF_MASKS
	select COS_MAPPED_TO_MSB
	select CAR_HAS_L3_PROTECTED_WAYS

config MAX_CPUS
	int
	default 24

config DCACHE_RAM_BASE
	default 0xfef00000

config DCACHE_RAM_SIZE
	default 0xc0000
	help
	  The size of the cache-as-ram region required during bootblock
	  and/or romstage.

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x80400
	help
	  The amount of anticipated stack usage in CAR by bootblock and
	  other stages. In the case of FSP_USES_CB_STACK default value will be
	  sum of FSP-M stack requirement(512KiB) and CB romstage stack requirement
	  (~1KiB).

config FSP_TEMP_RAM_SIZE
	hex
	default 0x20000
	help
	  The amount of anticipated heap usage in CAR by FSP.
	  Refer to Platform FSP integration guide document to know
	  the exact FSP requirement for Heap setup.

config CHIPSET_DEVICETREE
	string
	default "soc/intel/alderlake/chipset_pch_s.cb" if SOC_INTEL_ALDERLAKE_PCH_S
	default "soc/intel/alderlake/chipset.cb"

config EXT_BIOS_WIN_BASE
	default 0xf8000000

config EXT_BIOS_WIN_SIZE
	default 0x2000000

config IFD_CHIPSET
	string
	default "adl"

config IED_REGION_SIZE
	hex
	default 0x400000

config HEAP_SIZE
	hex
	default 0x10000

config GFX_GMA_DEFAULT_MMIO
	default 0xfa000000 if MAINBOARD_HAS_EARLY_LIBGFXINIT

# Intel recommends reserving the following resources per PCIe TBT root port,
# from ADL BIOS Spec (doc #627270) Revision 0.6.0 Section 7.2.5.1.5
# - 42 buses
# - 194 MiB Non-prefetchable memory
# - 448 MiB Prefetchable memory
if SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES

config PCIEXP_HOTPLUG_BUSES
	int
	default 42

config PCIEXP_HOTPLUG_MEM
	hex
	default 0xc200000

config PCIEXP_HOTPLUG_PREFETCH_MEM
	hex
	default 0x1c000000

endif # SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES

config MAX_PCH_ROOT_PORTS
	int
	default 10 if SOC_INTEL_ALDERLAKE_PCH_M
	default 12 if SOC_INTEL_ALDERLAKE_PCH_N
	default 12 if SOC_INTEL_ALDERLAKE_PCH_P
	default 28 if SOC_INTEL_ALDERLAKE_PCH_S

config MAX_CPU_ROOT_PORTS
	int
	default 1 if SOC_INTEL_ALDERLAKE_PCH_M
	default 0 if SOC_INTEL_ALDERLAKE_PCH_N
	default 3 if SOC_INTEL_ALDERLAKE_PCH_P || SOC_INTEL_ALDERLAKE_PCH_S

config MAX_TBT_ROOT_PORTS
	int
	default 0 if SOC_INTEL_ALDERLAKE_PCH_N || SOC_INTEL_ALDERLAKE_PCH_S
	default 2 if SOC_INTEL_ALDERLAKE_PCH_M
	default 4 if SOC_INTEL_ALDERLAKE_PCH_P

config MAX_ROOT_PORTS
	int
	default MAX_PCH_ROOT_PORTS

config MAX_PCIE_CLOCK_SRC
	int
	default 6 if SOC_INTEL_ALDERLAKE_PCH_M
	default 5 if SOC_INTEL_ALDERLAKE_PCH_N
	default 10 if SOC_INTEL_ALDERLAKE_PCH_P
	default 18 if SOC_INTEL_ALDERLAKE_PCH_S
	help
	  With external clock buffer, Alderlake-P can support up to three additional source clocks.
	  This is done by setting the corresponding GPIO pin(s) to native function to use as
	  SRCCLK_OE[6..9]. In addition, SRCCLK6 does not need to be set to free running clock.
	  If any of SRCCLKReq 6..9 is asserted, SRCCLK6 will be turned on.

config MAX_PCIE_CLOCK_REQ
	int
	default 6  if SOC_INTEL_ALDERLAKE_PCH_M
	default 5  if SOC_INTEL_ALDERLAKE_PCH_N
	default 10 if SOC_INTEL_ALDERLAKE_PCH_P
	default 18 if SOC_INTEL_ALDERLAKE_PCH_S

config SMM_TSEG_SIZE
	hex
	default 0x800000

config SMM_RESERVED_SIZE
	hex
	default 0x200000

config PCR_BASE_ADDRESS
	hex
	default 0xe0000000 if SOC_INTEL_ALDERLAKE_PCH_S
	default 0xfd000000
	help
	  This option allows you to select MMIO Base Address of sideband bus.

config ECAM_MMCONF_BASE_ADDRESS
	default 0xc0000000

config CPU_BCLK_MHZ
	int
	default 100

config SOC_INTEL_PERFORMANCE_CORE_SCALE_FACTOR
	int
	default 127

config SOC_INTEL_EFFICIENT_CORE_SCALE_FACTOR
	int
	default 100

config SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ
	int
	default 120

config CPU_XTAL_HZ
	default 38400000

config SOC_INTEL_UFS_CLK_FREQ_HZ
	int
	default 19200000

config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ
	int
	default 133

config SOC_INTEL_COMMON_BLOCK_GSPI_MAX
	int
	default 7

config SOC_INTEL_I2C_DEV_MAX
	int
	default 8

config SOC_INTEL_ALDERLAKE_S3
	bool
	default n
	help
	  Select if using S3 instead of S0ix to disable D3Cold.

config ENABLE_SATA_TEST_MODE
	bool "Enable test mode for SATA margining"
	default n
	help
	  Enable SATA test mode in FSP-S.

config SOC_INTEL_UART_DEV_MAX
	int
	default 7

config CONSOLE_UART_BASE_ADDRESS
	hex
	default 0xfe03e000
	depends on INTEL_LPSS_UART_FOR_CONSOLE

config VBT_DATA_SIZE_KB
	int
	default 9

# Clock divider parameters for 115200 baud rate
# Baudrate = (UART source clock * M) /(N *16)
# ADL UART source clock: 100MHz
config SOC_INTEL_COMMON_LPSS_UART_CLK_M_VAL
	hex
	default 0x25a

config SOC_INTEL_COMMON_LPSS_UART_CLK_N_VAL
	hex
	default 0x7fff

config VBOOT
	select VBOOT_MUST_REQUEST_DISPLAY
	select VBOOT_STARTS_IN_BOOTBLOCK
	select VBOOT_VBNV_CMOS
	select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH
	select VBOOT_X86_SHA256_ACCELERATION

# Default hash block size is 1KiB. Increasing it to 4KiB to improve
# hashing time as well as read time. This helps in improving
# boot time for Alder Lake.
config VBOOT_HASH_BLOCK_SIZE
	hex
	default 0x1000

config CBFS_SIZE
	default 0x200000

config PRERAM_CBMEM_CONSOLE_SIZE
	hex
	default 0x16000 if CONSOLE_SERIAL
	default 0x4000

config CONSOLE_CBMEM_BUFFER_SIZE
	hex
	default 0x100000 if CONSOLE_SERIAL
	default 0x40000

config FSP_TYPE_IOT
	bool
	default n
	help
	  This option allows to select FSP IOT type from 3rdparty/fsp repo

config FSP_HEADER_PATH
	string "Location of FSP headers"
	default "src/vendorcode/intel/fsp/fsp2_0/alderlake_n/" if SOC_INTEL_ALDERLAKE_PCH_N
	default "src/vendorcode/intel/fsp/fsp2_0/raptorlake/" if SOC_INTEL_RAPTORLAKE
	default "3rdparty/fsp/AlderLakeFspBinPkg/IoT/AlderLakeP/Include/" if SOC_INTEL_ALDERLAKE_PCH_P && FSP_TYPE_IOT
	default "3rdparty/fsp/AlderLakeFspBinPkg/IoT/AlderLakeS/Include/" if SOC_INTEL_ALDERLAKE_PCH_S && FSP_TYPE_IOT
	default "3rdparty/fsp/AlderLakeFspBinPkg/Client/AlderLakeP/Include/" if SOC_INTEL_ALDERLAKE_PCH_P
	default "3rdparty/fsp/AlderLakeFspBinPkg/Client/AlderLakeS/Include/" if SOC_INTEL_ALDERLAKE_PCH_S
	default "src/vendorcode/intel/fsp/fsp2_0/alderlake/"

config FSP_FD_PATH
	string
	depends on FSP_USE_REPO
	default "3rdparty/fsp/AlderLakeFspBinPkg/IoT/AlderLakeP/Fsp.fd" if SOC_INTEL_ALDERLAKE_PCH_P && FSP_TYPE_IOT
	default "3rdparty/fsp/AlderLakeFspBinPkg/IoT/AlderLakeS/Fsp.fd" if SOC_INTEL_ALDERLAKE_PCH_S && FSP_TYPE_IOT
	default "3rdparty/fsp/AlderLakeFspBinPkg/Client/AlderLakeP/Fsp.fd" if SOC_INTEL_ALDERLAKE_PCH_P
	default "3rdparty/fsp/AlderLakeFspBinPkg/Client/AlderLakeS/Fsp.fd" if SOC_INTEL_ALDERLAKE_PCH_S

config SOC_INTEL_ALDERLAKE_DEBUG_CONSENT
	int "Debug Consent for ADL"
	# USB DBC is more common for developers so make this default to 2 if
	# SOC_INTEL_DEBUG_CONSENT=y
	default 2 if SOC_INTEL_DEBUG_CONSENT
	default 0
	help
	  This is to control debug interface on SOC.
	  Setting non-zero value will allow to use DBC or DCI to debug SOC.
	  PlatformDebugConsent in FspmUpd.h has the details.

	  Desired platform debug type are
	  0:Disabled, 2:Enabled (All Probes+TraceHub), 6:Enable (Low Power),
	  7:Manual

config DATA_BUS_WIDTH
	int
	default 128

config DIMMS_PER_CHANNEL
	int
	default 2

config MRC_CHANNEL_WIDTH
	int
	default 16

config ACPI_ADL_IPU_ES_SUPPORT
	def_bool n
	help
	  Enables ACPI entry to provide silicon type information to IPU kernel driver.

config ALDERLAKE_ENABLE_SOC_WORKAROUND
	bool
	default y
	select SOC_INTEL_UFS_LTR_DISQUALIFY
	select SOC_INTEL_UFS_OCP_TIMER_DISABLE
	help
	  Selects the workarounds applicable for Alder Lake SoC.

config USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS
	bool
	help
	  Alder Lake SoC based OEM board design with UFS and non-UFS planned to use an
	  unified AP firmware which demanded to have a unified descriptor. It means UFS
	  controller needs to default fuse enabled to let UFS SKU to boot.

	  On such design with non-UFS SKU is exhibiting S0ix failure due to UFS remain
	  enabled in the strap although FSP-S is making the UFS controller function
	  disabled. The potential root cause of this behaviour is although the UFS
	  controller is function disabled but MPHY clock is still in active state.

	  A possible solution to this problem is to issue a warm reboot (if boot path is
	  S5->S0 or G3->S0) after disabling the UFS and let PMC to read the function
	  disable state of the UFS for disabling the MPHY clock.

	  Mainboard users with such board design where OEM would like to use an unified AP
	  firmware to support both UFS and non-UFS sku booting might need to choose this
	  config to allow disabling UFS while booting on the non-UFS SKU.
	  Note: selection of this config would introduce an additional warm reset in
	  cold-reset scenarios due to function disabling of the UFS controller.

choice
	prompt "Multiprocessor (MP) Initialization configuration to use"
	default USE_FSP_MP_INIT

config USE_FSP_MP_INIT
	bool "Use FSP MP init"
	select MP_SERVICES_PPI_V2
	help
	  Upon selection, coreboot brings APs from reset and the FSP runs feature programming.

config USE_COREBOOT_MP_INIT
	bool "Use coreboot MP init"
	# FSP assumes ownership of the APs (Application Processors)
	# upon passing `NULL` pointer to the CpuMpPpi FSP-S UPD.
	# Hence, select `MP_SERVICES_PPI_V2_NOOP` config to pass a valid
	# pointer to the CpuMpPpi UPD with FSP_UNSUPPORTED type APIs.
	# This will protect APs from getting hijacked by FSP while coreboot
	# decides to set SkipMpInit UPD.
	select MP_SERVICES_PPI_V2_NOOP
	select RELOAD_MICROCODE_PATCH
	help
	  Upon selection, coreboot performs MP Init.

endchoice

if STITCH_ME_BIN

config CSE_BPDT_VERSION
	default "1.7"

endif

config SI_DESC_REGION
	string "Descriptor Region name"
	default "SI_DESC"
	help
	  Name of Descriptor Region in the FMAP

config SI_DESC_REGION_SZ
	int
	default 4096
	help
	  Size of Descriptor Region in the FMAP

config BUILDING_WITH_DEBUG_FSP
	bool "Debug FSP is used for the build"
	default n
	help
	  Set this option if debug build of FSP is used.

config INTEL_GMA_BCLV_OFFSET
	default 0xc8258

config INTEL_GMA_BCLV_WIDTH
	default 32

config INTEL_GMA_BCLM_OFFSET
	default 0xc8254

config INTEL_GMA_BCLM_WIDTH
	default 32

endif