src/soc/amd/picasso/Kconfig

# SPDX-License-Identifier: GPL-2.0-only

config SOC_AMD_PICASSO
	bool
	help
	  AMD Picasso support

if SOC_AMD_PICASSO

config CPU_SPECIFIC_OPTIONS
	def_bool y
	select ACPI_SOC_NVS
	select ADD_FSP_BINARIES if USE_AMD_BLOBS
	select ARCH_BOOTBLOCK_X86_32
	select ARCH_VERSTAGE_X86_32 if !VBOOT_STARTS_BEFORE_BOOTBLOCK
	select ARCH_ROMSTAGE_X86_32
	select ARCH_RAMSTAGE_X86_32
	select ARCH_X86
	select BOOT_DEVICE_SUPPORTS_WRITES if BOOT_DEVICE_SPI_FLASH
	select CONSOLE_CBMEM_PRINT_PRE_BOOTBLOCK_CONTENTS if VBOOT_STARTS_BEFORE_BOOTBLOCK
	select DRIVERS_USB_PCI_XHCI
	select FSP_COMPRESS_FSP_M_LZMA
	select FSP_COMPRESS_FSP_S_LZMA
	select GENERIC_GPIO_LIB
	select HAVE_ACPI_TABLES
	select HAVE_CF9_RESET
	select HAVE_EM100_SUPPORT
	select HAVE_SMI_HANDLER
	select IDT_IN_EVERY_STAGE
	select NO_DDR5
	select NO_DDR3
	select NO_DDR2
	select NO_LPDDR4
	select PARALLEL_MP_AP_WORK
	select PLATFORM_USES_FSP2_0
	select PROVIDES_ROM_SHARING
	select RESET_VECTOR_IN_RAM
	select RTC
	select SOC_AMD_COMMON
	select SOC_AMD_COMMON_BLOCK_ACP_GEN1
	select SOC_AMD_COMMON_BLOCK_ACPI
	select SOC_AMD_COMMON_BLOCK_ACPIMMIO
	select SOC_AMD_COMMON_BLOCK_ACPI_ALIB
	select SOC_AMD_COMMON_BLOCK_ACPI_GPIO
	select SOC_AMD_COMMON_BLOCK_ACPI_IVRS
	select SOC_AMD_COMMON_BLOCK_AOAC
	select SOC_AMD_COMMON_BLOCK_APOB
	select SOC_AMD_COMMON_BLOCK_BANKED_GPIOS
	select SOC_AMD_COMMON_BLOCK_DATA_FABRIC
	select SOC_AMD_COMMON_BLOCK_GRAPHICS
	select SOC_AMD_COMMON_BLOCK_HAS_ESPI
	select SOC_AMD_COMMON_BLOCK_HDA
	select SOC_AMD_COMMON_BLOCK_I2C
	select SOC_AMD_COMMON_BLOCK_I2C_PAD_CTRL
	select SOC_AMD_COMMON_BLOCK_IOMMU
	select SOC_AMD_COMMON_BLOCK_LPC
	select SOC_AMD_COMMON_BLOCK_MCAX
	select SOC_AMD_COMMON_BLOCK_NONCAR
	select SOC_AMD_COMMON_BLOCK_PCI
	select SOC_AMD_COMMON_BLOCK_PCIE_GPP_DRIVER
	select SOC_AMD_COMMON_BLOCK_PM
	select SOC_AMD_COMMON_BLOCK_PM_CHIPSET_STATE_SAVE
	select SOC_AMD_COMMON_BLOCK_PSP_GEN2
	select SOC_AMD_COMMON_BLOCK_SATA
	select SOC_AMD_COMMON_BLOCK_SMBUS
	select SOC_AMD_COMMON_BLOCK_SMI
	select SOC_AMD_COMMON_BLOCK_SMM
	select SOC_AMD_COMMON_BLOCK_SMU
	select SOC_AMD_COMMON_BLOCK_SPI
	select SOC_AMD_COMMON_BLOCK_TSC_FAM17H_19H
	select SOC_AMD_COMMON_BLOCK_UART
	select SOC_AMD_COMMON_BLOCK_UCODE
	select SOC_AMD_COMMON_FSP_DMI_TABLES
	select SSE2
	select UDK_2017_BINDING
	select USE_DDR4
	select USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM
	select USE_FSP_NOTIFY_PHASE_READY_TO_BOOT
	select USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE
	select X86_AMD_FIXED_MTRRS
	select X86_INIT_NEED_1_SIPI

config ARCH_ALL_STAGES_X86
	default n

config CHIPSET_DEVICETREE
	string
	default "soc/amd/picasso/chipset.cb"

config FSP_M_FILE
	string "FSP-M (memory init) binary path and filename"
	depends on ADD_FSP_BINARIES
	default "3rdparty/amd_blobs/picasso/PICASSO_M.fd"
	help
	  The path and filename of the FSP-M binary for this platform.

config FSP_S_FILE
	string "FSP-S (silicon init) binary path and filename"
	depends on ADD_FSP_BINARIES
	default "3rdparty/amd_blobs/picasso/PICASSO_S.fd"
	help
	  The path and filename of the FSP-S binary for this platform.

config EARLY_RESERVED_DRAM_BASE
	hex
	default 0x2000000
	help
	  This variable defines the base address of the DRAM which is reserved
	  for usage by coreboot in early stages (i.e. before ramstage is up).
	  This memory gets reserved in BIOS tables to ensure that the OS does
	  not use it, thus preventing corruption of OS memory in case of S3
	  resume.

config EARLYRAM_BSP_STACK_SIZE
	hex
	default 0x1000

config PSP_APOB_DRAM_ADDRESS
	hex
	default 0x2001000
	help
	  Location in DRAM where the PSP will copy the AGESA PSP Output
	  Block.

config PSP_APOB_DRAM_SIZE
	hex
	default 0x10000

config PSP_SHAREDMEM_BASE
	hex
	default 0x2011000 if VBOOT
	default 0x0
	help
	  This variable defines the base address in DRAM memory where PSP copies
	  the vboot workbuf. This is used in the linker script to have a static
	  allocation for the buffer as well as for adding relevant entries in
	  the BIOS directory table for the PSP.

config PSP_SHAREDMEM_SIZE
	hex
	default 0x8000 if VBOOT
	default 0x0
	help
	  Sets the maximum size for the PSP to pass the vboot workbuf and
	  any logs or timestamps back to coreboot.  This will be copied
	  into main memory by the PSP and will be available when the x86 is
	  started.  The workbuf's base depends on the address of the reset
	  vector.

config PRE_X86_CBMEM_CONSOLE_SIZE
	hex
	default 0x1600
	help
	  Size of the CBMEM console used in PSP verstage.

config PRERAM_CBMEM_CONSOLE_SIZE
	hex
	default 0x1600
	help
	  Increase this value if preram cbmem console is getting truncated

config CBFS_MCACHE_SIZE
	hex
	default 0x2000 if VBOOT_STARTS_BEFORE_BOOTBLOCK

config C_ENV_BOOTBLOCK_SIZE
	hex
	default 0x10000
	help
	  Sets the size of the bootblock stage that should be loaded in DRAM.
	  This variable controls the DRAM allocation size in linker script
	  for bootblock stage.

config ROMSTAGE_ADDR
	hex
	default 0x2040000
	help
	  Sets the address in DRAM where romstage should be loaded.

config ROMSTAGE_SIZE
	hex
	default 0x80000
	help
	  Sets the size of DRAM allocation for romstage in linker script.

config FSP_M_ADDR
	hex
	default 0x20C0000
	help
	  Sets the address in DRAM where FSP-M should be loaded. cbfstool
	  performs relocation of FSP-M to this address.

config FSP_M_SIZE
	hex
	default 0xC0000
	help
	  Sets the size of DRAM allocation for FSP-M in linker script.

config VERSTAGE_ADDR
	hex
	depends on VBOOT_SEPARATE_VERSTAGE
	default 0x2180000
	help
	  Sets the address in DRAM where verstage should be loaded if running
	  as a separate stage on x86.

config VERSTAGE_SIZE
	hex
	depends on VBOOT_SEPARATE_VERSTAGE
	default 0x80000
	help
	  Sets the size of DRAM allocation for verstage in linker script if
	  running as a separate stage on x86.

config ECAM_MMCONF_BASE_ADDRESS
	default 0xF8000000

config ECAM_MMCONF_BUS_NUMBER
	default 64

config VERSTAGE_ADDR
	hex
	default 0x4000000

config MAX_CPUS
	int
	default 8
	help
	  Maximum number of threads the platform can have.

config VGA_BIOS_ID
	string
	default "1002,15d8,c1"
	help
	  The default VGA BIOS PCI vendor/device ID should be set to the
	  result of the map_oprom_vendev_rev() function in northbridge.c.

config VGA_BIOS_FILE
	string
	default "3rdparty/amd_blobs/picasso/PicassoGenericVbios.bin"

config VGA_BIOS_SECOND
	def_bool y

config VGA_BIOS_SECOND_ID
	string
	default "1002,15dd,c4"
	help
	  Because Dali and Picasso need different video BIOSes, but have the
	  same vendor/device IDs, we need an alternate method to determine the
	  correct video BIOS. In map_oprom_vendev_rev(), we look at the cpuid
	  and decide which rom to load.

	  Even though the hardware has the same vendor/device IDs, the vBIOS
	  contains a *different* device ID, confusing the situation even more.

config VGA_BIOS_SECOND_FILE
	string
	default "3rdparty/amd_blobs/picasso/Raven2GenericVbios.bin"

config CHECK_REV_IN_OPROM_NAME
	bool
	default y
	help
	  Select this in the platform BIOS or chipset if the option rom has a
	  revision that needs to be checked when searching CBFS.

config S3_VGA_ROM_RUN
	bool
	default n

config HEAP_SIZE
	hex
	default 0xc0000

config SERIRQ_CONTINUOUS_MODE
	bool
	default n
	help
	  Set this option to y for serial IRQ in continuous mode.
	  Otherwise it is in quiet mode.

config CONSOLE_UART_BASE_ADDRESS
	depends on CONSOLE_SERIAL && AMD_SOC_CONSOLE_UART
	hex
	default 0xfedc9000 if UART_FOR_CONSOLE = 0
	default 0xfedca000 if UART_FOR_CONSOLE = 1
	default 0xfedce000 if UART_FOR_CONSOLE = 2
	default 0xfedcf000 if UART_FOR_CONSOLE = 3

config SMM_TSEG_SIZE
	hex
	default 0x800000 if HAVE_SMI_HANDLER
	default 0x0

config SMM_RESERVED_SIZE
	hex
	default 0x180000

config SMM_MODULE_STACK_SIZE
	hex
	default 0x800

config ACPI_CPU_STRING
	string
	default "\\_SB.C%03d"

config ACPI_BERT
	bool "Build ACPI BERT Table"
	default y
	depends on HAVE_ACPI_TABLES
	help
	  Report Machine Check errors identified in POST to the OS in an
	  ACPI Boot Error Record Table.

config ACPI_BERT_SIZE
	hex
	default 0x4000 if ACPI_BERT
	default 0x0
	help
	  Specify the amount of DRAM reserved for gathering the data used to
	  generate the ACPI table.

config ACPI_SSDT_PSD_INDEPENDENT
	bool "Allow core p-state independent transitions"
	default y
	help
	  AMD recommends the ACPI _PSD object to be configured to cause
	  cores to transition between p-states independently. A vendor may
	  choose to generate _PSD object to allow cores to transition together.

config CHROMEOS
	select ALWAYS_LOAD_OPROM
	select ALWAYS_RUN_OPROM

config RO_REGION_ONLY
	string
	depends on VBOOT_SLOTS_RW_AB || VBOOT_SLOTS_RW_A
	default "apu/amdfw"

config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ
	int
	default 150

config DISABLE_SPI_FLASH_ROM_SHARING
	def_bool n
	help
	  Instruct the chipset to not honor the EGPIO67_SPI_ROM_REQ pin
	  which indicates a board level ROM transaction request. This
	  removes arbitration with board and assumes the chipset controls
	  the SPI flash bus entirely.

config DISABLE_KEYBOARD_RESET_PIN
	bool
	help
	  Instruct the SoC to not use the state of GPIO_129 as keyboard reset
	  signal. When this pin is used as GPIO and the keyboard reset
	  functionality isn't disabled, configuring it as an output and driving
	  it as 0 will cause a reset.

config FSP_TEMP_RAM_SIZE
	hex
	default 0x40000
	help
	  The amount of coreboot-allocated heap and stack usage by the FSP.

menu "PSP Configuration Options"

config AMD_FWM_POSITION_INDEX
	int "Firmware Directory Table location (0 to 5)"
	range 0 5
	default 0 if BOARD_ROMSIZE_KB_512
	default 1 if BOARD_ROMSIZE_KB_1024
	default 2 if BOARD_ROMSIZE_KB_2048
	default 3 if BOARD_ROMSIZE_KB_4096
	default 4 if BOARD_ROMSIZE_KB_8192
	default 5 if BOARD_ROMSIZE_KB_16384
	help
	  Typically this is calculated by the ROM size, but there may
	  be situations where you want to put the firmware directory
	  table in a different location.
	    0: 512 KB - 0xFFFA0000
	    1: 1 MB   - 0xFFF20000
	    2: 2 MB   - 0xFFE20000
	    3: 4 MB   - 0xFFC20000
	    4: 8 MB   - 0xFF820000
	    5: 16 MB  - 0xFF020000

comment "AMD Firmware Directory Table set to location for 512KB ROM"
	depends on AMD_FWM_POSITION_INDEX = 0
comment "AMD Firmware Directory Table set to location for 1MB ROM"
	depends on AMD_FWM_POSITION_INDEX = 1
comment "AMD Firmware Directory Table set to location for 2MB ROM"
	depends on AMD_FWM_POSITION_INDEX = 2
comment "AMD Firmware Directory Table set to location for 4MB ROM"
	depends on AMD_FWM_POSITION_INDEX = 3
comment "AMD Firmware Directory Table set to location for 8MB ROM"
	depends on AMD_FWM_POSITION_INDEX = 4
comment "AMD Firmware Directory Table set to location for 16MB ROM"
	depends on AMD_FWM_POSITION_INDEX = 5

config AMDFW_CONFIG_FILE
	string
	default "src/soc/amd/picasso/fw.cfg"

config PSP_LOAD_MP2_FW
	bool
	default n
	help
	  Include the MP2 firmwares and configuration into the PSP build.

	  If unsure, answer 'n'

config PSP_LOAD_S0I3_FW
	bool
	default n
	help
	  Select this item to include the S0i3 file into the PSP build.

config HAVE_PSP_WHITELIST_FILE
	bool "Include a debug whitelist file in PSP build"
	default n
	help
	  Support secured unlock prior to reset using a whitelisted
	  number?  This feature requires a signed whitelist image and
	  bootloader from AMD.

	  If unsure, answer 'n'

config PSP_WHITELIST_FILE
	string "Debug whitelist file path"
	depends on HAVE_PSP_WHITELIST_FILE
	default "3rdparty/amd_blobs/picasso/PSP/wtl-rvn.sbin"

config PSP_UNLOCK_SECURE_DEBUG
	bool "Unlock secure debug"
	default n
	help
	  Select this item to enable secure debug options in PSP.

config PSP_VERSTAGE_FILE
	string "Specify the PSP_verstage file path"
	depends on VBOOT_STARTS_BEFORE_BOOTBLOCK
	default "\$(obj)/psp_verstage.bin"
	help
	  Add psp_verstage file to the build & PSP Directory Table

config PSP_VERSTAGE_SIGNING_TOKEN
	string "Specify the PSP_verstage Signature Token file path"
	depends on VBOOT_STARTS_BEFORE_BOOTBLOCK
	default ""
	help
	  Add psp_verstage signature token to the build & PSP Directory Table

config PSP_SOFTFUSE_BITS
	string "PSP Soft Fuse bits to enable"
	default "28"
	help
	  Space separated list of Soft Fuse bits to enable.
	  Bit 0:  Enable secure debug (Set by PSP_UNLOCK_SECURE_DEBUG)
	  Bit 15: PSP post code destination: 0=LPC 1=eSPI
	  Bit 29: Disable MP2 firmware loading (Set by PSP_LOAD_MP2_FW)

	  See #55758 (NDA) for additional bit definitions.

endmenu

config VBOOT
	select VBOOT_VBNV_CMOS
	select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH

config VBOOT_STARTS_BEFORE_BOOTBLOCK
	def_bool n
	depends on VBOOT
	select ARCH_VERSTAGE_ARMV7
	help
	  Runs verstage on the PSP.  Only available on
	  certain ChromeOS branded parts from AMD.

config VBOOT_HASH_BLOCK_SIZE
	hex
	default 0x9000
	depends on VBOOT_STARTS_BEFORE_BOOTBLOCK
	help
	  Because the bulk of the time in psp_verstage to hash the RO cbfs is
	  spent in the overhead of doing svc calls, increasing the hash block
	  size significantly cuts the verstage hashing time as seen below.

	  4k takes 180ms
	  16k takes 44ms
	  32k takes 33.7ms
	  36k takes 32.5ms
	  There's actually still room for an even bigger stack, but we've
	  reached a point of diminishing returns.

config CMOS_RECOVERY_BYTE
	hex
	default 0x51
	depends on VBOOT_STARTS_BEFORE_BOOTBLOCK
	help
	  If the workbuf is not passed from the PSP to coreboot, set the
	  recovery flag and reboot.  The PSP will read this byte, mark the
	  recovery request in VBNV, and reset the system into recovery mode.

	  This is the byte before the default first byte used by VBNV
	  (0x26 + 0x0E - 1)

if VBOOT_SLOTS_RW_A && VBOOT_STARTS_BEFORE_BOOTBLOCK

config RWA_REGION_ONLY
	string
	default "apu/amdfw_a"
	help
	  Add a space-delimited list of filenames that should only be in the
	  RW-A section.

endif # VBOOT_SLOTS_RW_A && VBOOT_STARTS_BEFORE_BOOTBLOCK

if VBOOT_SLOTS_RW_AB && VBOOT_STARTS_BEFORE_BOOTBLOCK

config RWB_REGION_ONLY
	string
	default "apu/amdfw_b"
	help
	  Add a space-delimited list of filenames that should only be in the
	  RW-B section.

endif # VBOOT_SLOTS_RW_AB && VBOOT_STARTS_BEFORE_BOOTBLOCK

endif # SOC_AMD_PICASSO