src/mainboard/intel/kunimitsu/devicetree.cb

chip soc/intel/skylake

	# Enable deep Sx states
	register "deep_s5_enable_ac" = "1"
	register "deep_s5_enable_dc" = "1"
	register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "gpe0_dw0" = "GPP_B"
	register "gpe0_dw1" = "GPP_D"
	register "gpe0_dw2" = "GPP_E"

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"

	# Enable DPTF
	register "dptf_enable" = "1"

	# FSP Configuration
	register "DspEnable" = "1"
	register "IoBufferOwnership" = "3"
	register "ScsEmmcHs400Enabled" = "1"
	register "SkipExtGfxScan" = "1"
	register "SaGv" = "SaGv_Enabled"

	# Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch
	# SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s
	register "PmConfigSlpS3MinAssert" = "0x02"

	# SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s
	register "PmConfigSlpS4MinAssert" = "0x04"

	# SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s
	register "PmConfigSlpSusMinAssert" = "0x03"

	# SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s
	register "PmConfigSlpAMinAssert" = "0x03"


	# VR Settings Configuration for 4 Domains
	#+----------------+-----------+-----------+-------------+----------+
	#| Domain/Setting |     SA    |    IA     | GT Unsliced |    GT    |
	#+----------------+-----------+-----------+-------------+----------+
	#| Psi1Threshold  | 20A       | 20A       | 20A         | 20A      |
	#| Psi2Threshold  | 4A        | 5A        | 5A          | 5A       |
	#| Psi3Threshold  | 1A        | 1A        | 1A          | 1A       |
	#| Psi3Enable     | 1         | 1         | 1           | 1        |
	#| Psi4Enable     | 1         | 1         | 1           | 1        |
	#| ImonSlope      | 0         | 0         | 0           | 0        |
	#| ImonOffset     | 0         | 0         | 0           | 0        |
	#| IccMax         | 7A        | 34A       | 35A         | 35A      |
	#| VrVoltageLimit | 1.52V     | 1.52V     | 1.52V       | 1.52V    |
	#+----------------+-----------+-----------+-------------+----------+
	register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(4),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(7),
		.voltage_limit = 1520,
	}"

	register "domain_vr_config[VR_IA_CORE]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(34),
		.voltage_limit = 1520,
	}"

	register "domain_vr_config[VR_GT_UNSLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(35),
		.voltage_limit = 1520,
	}"

	register "domain_vr_config[VR_GT_SLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(5),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(35),
		.voltage_limit = 1520,
	}"

	# Enable Root port 1 and 5.
	register "PcieRpEnable[0]" = "1"
	register "PcieRpEnable[4]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[0]" = "1"
	register "PcieRpClkReqSupport[4]" = "1"
	# RP 1 uses SRCCLKREQ1# while RP 5 uses SRCCLKREQ2#
	register "PcieRpClkReqNumber[0]" = "1"
	register "PcieRpClkReqNumber[4]" = "2"

	register "usb2_ports" = "{
		[0] = USB2_PORT_TYPE_C(OC0),	/* Type-C Port 1 */
		[1] = USB2_PORT_TYPE_C(OC1),	/* Type-C Port 2 */
		[2] = USB2_PORT_MID(OC_SKIP),	/* Bluetooth */
		[4] = USB2_PORT_MID(OC2),	/* Type-A Port (card) */
		[6] = USB2_PORT_FLEX(OC_SKIP),	/* Camera */
		[8] = USB2_PORT_LONG(OC3),	/* Type-A Port (board) */
	}"

	register "usb3_ports" = "{
		[0] = USB3_PORT_DEFAULT(OC0),	/* Type-C Port 1 */
		[1] = USB3_PORT_DEFAULT(OC1),	/* Type-C Port 2 */
		[2] = USB3_PORT_DEFAULT(OC2),	/* Type-A Port (card) */
		[3] = USB3_PORT_DEFAULT(OC3),	/* Type-A Port (board) */
	}"

	register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8"  # I2C4 is 1.8V

	# Must leave UART0 enabled or SD/eMMC will not work as PCI
	register "SerialIoDevMode" = "{
		[PchSerialIoIndexI2C0]  = PchSerialIoPci,
		[PchSerialIoIndexI2C1]  = PchSerialIoPci,
		[PchSerialIoIndexI2C2]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C3]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C4]  = PchSerialIoPci,
		[PchSerialIoIndexI2C5]  = PchSerialIoDisabled,
		[PchSerialIoIndexSpi0]  = PchSerialIoDisabled,
		[PchSerialIoIndexSpi1]  = PchSerialIoDisabled,
		[PchSerialIoIndexUart0] = PchSerialIoPci,
		[PchSerialIoIndexUart1] = PchSerialIoDisabled,
		[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
	}"

	# PL2 override 25W
	register "power_limits_config" = "{
		.tdp_pl2_override = 25,
	}"

	# Send an extra VR mailbox command for the PS4 exit issue
	register "SendVrMbxCmd" = "2"

	# Use default SD card detect GPIO configuration
	register "sdcard_cd_gpio" = "GPP_A7"

	device domain 0 on
		device ref igpu		on  end
		device ref sa_thermal	on  end
		device ref south_xhci	on  end
		device ref thermal	on  end
		device ref i2c0		on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0001""
				register "desc" = ""ELAN Touchscreen""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)"
				device i2c 10 on end
			end
		end
		device ref i2c1		on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
				register "wake" = "GPE0_DW0_05"
				device i2c 15 on end
			end
		end
		device ref heci1	on  end
		device ref uart2	on  end
		device ref i2c4		on
			chip drivers/i2c/nau8825
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)"
				register "jkdet_enable" = "1"
				register "jkdet_pull_enable" = "1"
				register "jkdet_pull_up" = "1"
				register "jkdet_polarity" = "1"      # ActiveLow
				register "vref_impedance" = "2"      # 125kOhm
				register "micbias_voltage" = "6"     # 2.754
				register "sar_threshold_num" = "4"
				register "sar_threshold[0]" = "0x08"
				register "sar_threshold[1]" = "0x12"
				register "sar_threshold[2]" = "0x26"
				register "sar_threshold[3]" = "0x73"
				register "sar_hysteresis" = "0"
				register "sar_voltage" = "6"
				register "sar_compare_time" = "1"     # 1us
				register "sar_sampling_time" = "1"    # 4us
				register "short_key_debounce" = "3"   # 30ms
				register "jack_insert_debounce" = "7" # 512ms
				register "jack_eject_debounce" = "0"
				device i2c 1a on end
			end
			chip drivers/i2c/generic
				register "hid" = ""INT343B""
				register "desc" = ""SSM4567 Left Speaker Amp""
				register "uid" = "0"
				register "device_present_gpio" = "GPP_E3"
				device i2c 34 on end
			end
			chip drivers/i2c/generic
				register "hid" = ""INT343B""
				register "desc" = ""SSM4567 Right Speaker Amp""
				register "uid" = "1"
				register "device_present_gpio" = "GPP_E3"
				device i2c 35 on end
			end
		end
		device ref pcie_rp1	on
			chip drivers/wifi/generic
				register "wake" = "GPE0_DW0_16"
				device pci 00.0 on end
			end
		end
		device ref pcie_rp5	on end
		device ref uart0	on end
		device ref emmc		on end
		device ref sdxc		on end
		device ref lpc_espi	on
			chip drivers/pc80/tpm
				device pnp 0c31.0 on end
			end
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end
		device ref hda on
			chip drivers/generic/max98357a
				register "hid" = ""MX98357A""
				register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)"
				register "device_present_gpio" = "GPP_E3"
				register "device_present_gpio_invert" = "1"
				device generic 0 on end
			end
		end
		device ref smbus	on end
		device ref fast_spi	on end
	end
end