src/mainboard/google/poppy/variants/nocturne/devicetree.cb

chip soc/intel/skylake

	# Deep Sx states
	register "deep_s3_enable_ac" = "0"
	register "deep_s3_enable_dc" = "0"
	register "deep_s5_enable_ac" = "1"
	register "deep_s5_enable_dc" = "1"
	register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN | DSX_EN_WAKE_PIN | DSX_DIS_AC_PRESENT_PD"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "gpe0_dw0" = "GPP_C"
	register "gpe0_dw1" = "GPP_D"
	register "gpe0_dw2" = "GPP_E"

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"
	# EC memory map range is 0x900-0x9ff
	register "gen3_dec" = "0x00fc0901"

	# Enable DPTF
	register "dptf_enable" = "1"

	# Enable S0ix
	register "s0ix_enable" = "1"

	# FSP Configuration
	register "ProbelessTrace" = "0"
	register "EnableLan" = "0"
	register "EnableSata" = "0"
	register "SataSalpSupport" = "0"
	register "SataMode" = "0"
	register "SataPortsEnable[0]" = "0"
	register "EnableAzalia" = "1"
	register "DspEnable" = "1"
	register "IoBufferOwnership" = "3"
	register "EnableTraceHub" = "0"
	register "SsicPortEnable" = "0"
	register "SmbusEnable" = "1"
	register "Cio2Enable" = "1"
	register "SaImguEnable" = "1"
	register "ScsEmmcEnabled" = "1"
	register "ScsEmmcHs400Enabled" = "1"
	register "ScsSdCardEnabled" = "0"
	register "PttSwitch" = "0"
	register "InternalGfx" = "1"
	register "SkipExtGfxScan" = "1"
	register "Device4Enable" = "1"
	register "HeciEnabled" = "0"
	register "SaGv" = "3"
	register "SerialIrqConfigSirqEnable" = "1"
	register "PmConfigSlpS3MinAssert" = "2"        # 50ms
	register "PmConfigSlpS4MinAssert" = "1"        # 1s
	register "PmConfigSlpSusMinAssert" = "1"       # 500ms
	register "PmConfigSlpAMinAssert" = "3"         # 2s
	register "PmTimerDisabled" = "1"
	register "VmxEnable" = "1"

	# Set speed_shift_enable to 1 to enable P-States, and 0 to disable
	register "speed_shift_enable" = "1"
	register "dptf_enable" = "1"
	register "tdp_pl2_override" = "18"
	register "psys_pmax" = "45"
	register "tcc_offset" = "10"
	register "pch_trip_temp" = "75"

	register "pirqa_routing" = "PCH_IRQ11"
	register "pirqb_routing" = "PCH_IRQ10"
	register "pirqc_routing" = "PCH_IRQ11"
	register "pirqd_routing" = "PCH_IRQ11"
	register "pirqe_routing" = "PCH_IRQ11"
	register "pirqf_routing" = "PCH_IRQ11"
	register "pirqg_routing" = "PCH_IRQ11"
	register "pirqh_routing" = "PCH_IRQ11"

	# VR Settings Configuration for 4 Domains
	#+----------------+-------+-------+-------+-------+
	#| Domain/Setting |  SA   |  IA   | GTUS  |  GTS  |
	#+----------------+-------+-------+-------+-------+
	#| Psi1Threshold  | 20A   | 20A   | 20A   | 20A   |
	#| Psi2Threshold  | 2A    | 2A    | 2A    | 2A    |
	#| Psi3Threshold  | 1A    | 1A    | 1A    | 1A    |
	#| Psi3Enable     | 1     | 1     | 1     | 1     |
	#| Psi4Enable     | 1     | 1     | 1     | 1     |
	#| ImonSlope      | 0     | 0     | 0     | 0     |
	#| ImonOffset     | 0     | 0     | 0     | 0     |
	#| IccMax         | Set by SoC code per CPU SKU   |
	#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
	#| AcLoadline     | 14.9  | 4     | 5.7   | 4.57  |
	#| DcLoadline     | 14.2  | 4     | 4.2   | 4.3   |
	#+----------------+-------+-------+-------+-------+
	register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 1490,
		.dc_loadline = 1420,
	}"

	register "domain_vr_config[VR_IA_CORE]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 400,
		.dc_loadline = 400,
	}"

	register "domain_vr_config[VR_GT_UNSLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 570,
		.dc_loadline = 420,
	}"

	register "domain_vr_config[VR_GT_SLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.voltage_limit = 1520,
		.ac_loadline = 457,
		.dc_loadline = 430,
	}"

	# PCIe Root port 1 with SRCCLKREQ1#
	register "PcieRpEnable[0]" = "1"
	register "PcieRpClkReqSupport[0]" = "1"
	register "PcieRpClkReqNumber[0]" = "1"
	register "PcieRpClkSrcNumber[0]" = "1"
	register "PcieRpAdvancedErrorReporting[0]" = "1"
	register "PcieRpLtrEnable[0]" = "1"

        # Root port 9 (x2)
        #  PcieRpEnable:                 Enable root port
        #  PcieRpClkReqSupport:          Enable CLKREQ#
        #  PcieRpClkReqNumber:           Uses SRCCLKREQ2#
        #  PcieRpClkSrcNumber:           Uses 3
        #  PcieRpAdvancedErrorReporting: Enable Advanced Error Reporting
        #  PcieRpLtrEnable:              Enable Latency Tolerance Reporting Mechanism
        register "PcieRpEnable[8]" = "1"
        register "PcieRpClkReqSupport[8]" = "1"
        register "PcieRpClkReqNumber[8]" = "2"
        register "PcieRpClkSrcNumber[8]" = "3"
        register "PcieRpAdvancedErrorReporting[8]" = "1"
        register "PcieRpLtrEnable[8]" = "1"

	# USB 2.0
	register "usb2_ports[0]" = "USB2_PORT_LONG(OC0)"	# Type-C Port 1
	register "usb2_ports[1]" = "USB2_PORT_EMPTY"		# Empty
	register "usb2_ports[2]" = "USB2_PORT_SHORT(OC_SKIP)"	# Bluetooth
	register "usb2_ports[4]" = "USB2_PORT_LONG(OC1)"	# Type-C Port 2
	register "usb2_ports[6]" = "USB2_PORT_LONG(OC_SKIP)"	# pogo port
	register "usb2_ports[7]" = "USB2_PORT_EMPTY"		# Empty
	register "usb2_ports[8]" = "USB2_PORT_EMPTY"		# Empty

	# USB 3.0
	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)"	# Type-C Port 1
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)"	# Type-C Port 2
	register "usb3_ports[2]" = "USB3_PORT_EMPTY"		# Empty
	register "usb3_ports[3]" = "USB3_PORT_EMPTY"		# Empty

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| chipset_lockdown  | CHIPSET_LOCKDOWN_COREBOOT |
	#| GSPI0             | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#|                   | before memory is up       |
	#| I2C0              | Touchscreen               |
	#| I2C1              | Trackpad                  |
	#| I2C3              | Camera                    |
	#| I2C4              | Audio                     |
	#| I2C5              | Rear Camera & SAR         |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 98,
			.fall_time_ns = 38,
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 186,
				.scl_hcnt = 93,
				.sda_hold = 36,
			},
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 98,
			.fall_time_ns = 38,
		},
		.i2c[4] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 176,
				.scl_hcnt = 95,
				.sda_hold = 36,
			}
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 98,
			.fall_time_ns = 38,
		},
		.gspi[0] = {
			.speed_mhz = 1,
			.early_init = 1,
		},
	}"
	# Touchscreen
	register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3"

	# Trackpad
	register "i2c_voltage[1]" = "I2C_VOLTAGE_1V8"

	# Front Camera
	register "i2c_voltage[3]" = "I2C_VOLTAGE_1V8"

	# Audio
	register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8"

	# Rear Camera & SAR
	register "i2c_voltage[5]" = "I2C_VOLTAGE_1V8"

	register "SerialIoDevMode" = "{
		[PchSerialIoIndexI2C0]  = PchSerialIoPci,
		[PchSerialIoIndexI2C1]  = PchSerialIoPci,
		[PchSerialIoIndexI2C2]  = PchSerialIoDisabled,
		[PchSerialIoIndexI2C3]  = PchSerialIoPci,
		[PchSerialIoIndexI2C4]  = PchSerialIoPci,
		[PchSerialIoIndexI2C5]  = PchSerialIoPci,
		[PchSerialIoIndexSpi0]  = PchSerialIoPci,
		[PchSerialIoIndexSpi1]  = PchSerialIoPci,
		[PchSerialIoIndexUart0] = PchSerialIoSkipInit,
		[PchSerialIoIndexUart1] = PchSerialIoDisabled,
		[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
	}"

	device cpu_cluster 0 on
		device lapic 0 on end
	end
	device domain 0 on
		device pci 00.0 on  end # Host Bridge
		device pci 02.0 on  end # Integrated Graphics Device
		device pci 14.0 on  end # USB xHCI
		device pci 14.1 on  end # USB xDCI (OTG)
		device pci 14.2 on  end # Thermal Subsystem
		device pci 15.0 on
			chip drivers/i2c/hid
				register "generic.hid" = ""WCOM50C1""
				register "generic.desc" = ""WCOM Digitizer""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)"
				register "generic.speed" = "I2C_SPEED_FAST_PLUS"
                                register "generic.probed" = "1"
                                register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E11)"
                                register "generic.reset_delay_ms" = "1"
                                register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C22)"
                                register "generic.enable_delay_ms" = "1"
                                register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x1"
				device i2c 0a on end
			end
		end # I2C #0 - Touchscreen
		device pci 15.1 on
			chip drivers/i2c/sx9310
				register "desc" = ""Right SAR Proximity Sensor""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D9_IRQ)"
				register "speed" = "I2C_SPEED_FAST_PLUS"
				register "uid" = "0"
				register "reg_prox_ctrl0" = "0x10"
				register "reg_prox_ctrl1" = "0x00"
				register "reg_prox_ctrl2" = "0x84"
				register "reg_prox_ctrl3" = "0x0e"
				register "reg_prox_ctrl4" = "0x07"
				register "reg_prox_ctrl5" = "0xc6"
				register "reg_prox_ctrl6" = "0x20"
				register "reg_prox_ctrl7" = "0x0d"
				register "reg_prox_ctrl8" = "0x8d"
				register "reg_prox_ctrl9" = "0x43"
				register "reg_prox_ctrl10" = "0x11"
				register "reg_prox_ctrl11" = "0x00"
				register "reg_prox_ctrl12" = "0x00"
				register "reg_prox_ctrl13" = "0x00"
				register "reg_prox_ctrl14" = "0x00"
				register "reg_prox_ctrl15" = "0x00"
				register "reg_prox_ctrl16" = "0x00"
				register "reg_prox_ctrl17" = "0x00"
				register "reg_prox_ctrl18" = "0x00"
				register "reg_prox_ctrl19" = "0x00"
				register "reg_sar_ctrl0" = "0x50"
				register "reg_sar_ctrl1" = "0x8a"
				register "reg_sar_ctrl2" = "0x3c"
				device i2c 28 on end
			end
		end # I2C #1
		device pci 15.2 off end # I2C #2
		device pci 15.3 on  end # I2C #3 - Camera
		device pci 16.0 on  end # Management Engine Interface 1
		device pci 16.1 off end # Management Engine Interface 2
		device pci 16.2 off end # Management Engine IDE-R
		device pci 16.3 off end # Management Engine KT Redirection
		device pci 16.4 off end # Management Engine Interface 3
		device pci 17.0 off end # SATA
		device pci 19.0 on  end # UART #2
		device pci 19.1 on
			chip drivers/i2c/sx9310
				register "desc" = ""Left SAR Proximity Sensor""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D10_IRQ)"
				register "speed" = "I2C_SPEED_FAST_PLUS"
				register "uid" = "1"
				register "reg_prox_ctrl0" = "0x10"
				register "reg_prox_ctrl1" = "0x00"
				register "reg_prox_ctrl2" = "0x84"
				register "reg_prox_ctrl3" = "0x0e"
				register "reg_prox_ctrl4" = "0x07"
				register "reg_prox_ctrl5" = "0xc6"
				register "reg_prox_ctrl6" = "0x20"
				register "reg_prox_ctrl7" = "0x0d"
				register "reg_prox_ctrl8" = "0x8d"
				register "reg_prox_ctrl9" = "0x43"
				register "reg_prox_ctrl10" = "0x11"
				register "reg_prox_ctrl11" = "0x00"
				register "reg_prox_ctrl12" = "0x00"
				register "reg_prox_ctrl13" = "0x00"
				register "reg_prox_ctrl14" = "0x00"
				register "reg_prox_ctrl15" = "0x00"
				register "reg_prox_ctrl16" = "0x00"
				register "reg_prox_ctrl17" = "0x00"
				register "reg_prox_ctrl18" = "0x00"
				register "reg_prox_ctrl19" = "0x00"
				register "reg_sar_ctrl0" = "0x50"
				register "reg_sar_ctrl1" = "0x8a"
				register "reg_sar_ctrl2" = "0x3c"
				device i2c 28 on end
			end
		end # I2C #5
		device pci 19.2 on
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "4"
				register "imon_slot_no" = "5"
				register "uid" = "0"
				register "desc" = ""RIGHT SPEAKER AMP""
				register "name" = ""MAXR""
				device i2c 32 on end
			end
			chip drivers/i2c/max98373
				register "vmon_slot_no" = "6"
				register "imon_slot_no" = "7"
				register "uid" = "1"
				register "desc" = ""LEFT SPEAKER AMP""
				register "name" = ""MAXL""
				device i2c 31 on end
			end
		end # I2C #4 - Audio
		device pci 1c.0 on
			chip drivers/intel/wifi
				register "wake" = "GPE0_PCI_EXP"
				device pci 00.0 on end
			end
		end # PCI Express Port 1
		device pci 1c.1 off end # PCI Express Port 2
		device pci 1c.2 off end # PCI Express Port 3
		device pci 1c.3 off end # PCI Express Port 4
		device pci 1c.4 off end # PCI Express Port 5
		device pci 1c.5 off end # PCI Express Port 6
		device pci 1c.6 off end # PCI Express Port 7
		device pci 1c.7 off end # PCI Express Port 8
		device pci 1d.0 on  end # PCI Express Port 9
		device pci 1d.1 off end # PCI Express Port 10
		device pci 1d.2 off end # PCI Express Port 11
		device pci 1d.3 off end # PCI Express Port 12
		device pci 1e.0 off end # UART #0
		device pci 1e.1 off end # UART #1
		device pci 1e.2 on
			chip drivers/spi/acpi
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "compat_string" = ""google,cr50""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E0_IRQ)"
				device spi 0 on end
			end
		end # GSPI #0
		device pci 1e.3 on
			chip drivers/spi/acpi
				register "hid" = "ACPI_DT_NAMESPACE_HID"
				register "uid" = "1"
				register "compat_string" = ""google,cros-ec-spi""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C11_IRQ)"
				register "wake" = "GPE0_DW0_09" # GPP_C9
				device spi 0 on end
			end # FPMCU
		end # GSPI #1
		device pci 1e.4 on  end # eMMC
		device pci 1e.5 off end # SDIO
		device pci 1e.6 off end # SDCard
		device pci 1f.0 on
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end # LPC Interface
		device pci 1f.1 on  end # P2SB
		device pci 1f.2 on  end # Power Management Controller
		device pci 1f.3 on  end # Intel HDA
		device pci 1f.4 on  end # SMBus
		device pci 1f.5 on  end # PCH SPI
		device pci 1f.6 off end # GbE
	end
end