src/soc/intel/broadwell/Kconfig

config SOC_INTEL_BROADWELL
	bool
	help
	  Intel Broadwell and Haswell ULT support.

if SOC_INTEL_BROADWELL

config INTEL_LYNXPOINT_LP
	bool
	default y if SOC_INTEL_BROADWELL

config SOC_SPECIFIC_OPTIONS
	def_bool y
	select ACPI_HAS_DEVICE_NVS
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select BOOT_DEVICE_SUPPORTS_WRITES
	select CACHE_MRC_SETTINGS
	select CPU_INTEL_HASWELL
	select MRC_SETTINGS_PROTECT
	select HAVE_SMI_HANDLER
	select SOUTHBRIDGE_INTEL_COMMON_ACPI_MADT
	select SOUTHBRIDGE_INTEL_COMMON_EARLY_SMBUS
	select SOUTHBRIDGE_INTEL_COMMON_RESET
	select SOUTHBRIDGE_INTEL_COMMON_RTC
	select SOUTHBRIDGE_INTEL_COMMON_SMBUS
	select SOUTHBRIDGE_INTEL_COMMON_SPI_ICH9
	select HAVE_USBDEBUG
	select IOAPIC
	select INTEL_LYNXPOINT_LP
	select REG_SCRIPT
	select RTC
	select SPI_FLASH
	select SOC_INTEL_COMMON
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select HAVE_EM100PRO_SPI_CONSOLE_SUPPORT
	select INTEL_GMA_ACPI
	select HAVE_POWER_STATE_AFTER_FAILURE
	select HAVE_POWER_STATE_PREVIOUS_AFTER_FAILURE

config PCIEXP_ASPM
	bool
	default y

config PCIEXP_AER
	bool
	default y

config PCIEXP_COMMON_CLOCK
	bool
	default y

config PCIEXP_CLK_PM
	bool
	default y

config PCIEXP_L1_SUB_STATE
	bool
	default y

config BROADWELL_VBOOT_IN_BOOTBLOCK
	depends on VBOOT
	bool "Start verstage in bootblock"
	default y
	select VBOOT_STARTS_IN_BOOTBLOCK
	select VBOOT_SEPARATE_VERSTAGE
	help
	  Broadwell can either start verstage in a separate stage
	  right after the bootblock has run or it can start it
	  after romstage for compatibility reasons.
	  Broadwell however uses a mrc.bin to initialse memory which
	  needs to be located at a fixed offset. Therefore even with
	  a separate verstage starting after the bootblock that same
	  binary is used meaning a jump is made from RW to the RO region
	  and back to the RW region after the binary is done.

config VBOOT
	select VBOOT_MUST_REQUEST_DISPLAY
	select VBOOT_STARTS_IN_ROMSTAGE if !BROADWELL_VBOOT_IN_BOOTBLOCK

config MMCONF_BASE_ADDRESS
	default 0xf0000000

config MMCONF_BUS_NUMBER
	default 64

config VGA_BIOS_ID
	string
	default "8086,0406"

config FIXED_MCHBAR_MMIO_BASE
	default 0xfed10000

config FIXED_DMIBAR_MMIO_BASE
	default 0xfed18000

config FIXED_EPBAR_MMIO_BASE
	default 0xfed19000

config DCACHE_RAM_BASE
	hex
	default 0xff7c0000

config DCACHE_RAM_SIZE
	hex
	default 0x10000
	help
	  The size of the cache-as-ram region required during bootblock
	  and/or romstage. Note DCACHE_RAM_SIZE and DCACHE_RAM_MRC_VAR_SIZE
	  must add up to a power of 2.

config DCACHE_RAM_MRC_VAR_SIZE
	hex
	default 0x30000
	help
	  The amount of cache-as-ram region required by the reference code.

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x2000
	help
	  The amount of anticipated stack usage in CAR by bootblock and
	  other stages.

config HAVE_MRC
	bool "Add a Memory Reference Code binary"
	help
	  Select this option to add a Memory Reference Code binary to
	  the resulting coreboot image.

	  Note: Without this binary coreboot will not work

if HAVE_MRC

config MRC_FILE
	string "Intel Memory Reference Code path and filename"
	depends on HAVE_MRC
	default "mrc.bin"
	help
	  The filename of the file to use as Memory Reference Code binary.

config MRC_BIN_ADDRESS
	hex
	default 0xfffa0000

# The UEFI System Agent binary needs to be at a fixed offset in the flash
# and can therefore only reside in the COREBOOT fmap region
config RO_REGION_ONLY
	string
	depends on VBOOT
	default "mrc.bin"

endif # HAVE_MRC

config INTEL_PCH_UART_CONSOLE
	bool "Use Serial IO UART for console"
	default n
	select DRIVERS_UART_8250MEM

config INTEL_PCH_UART_CONSOLE_NUMBER
	hex "Serial IO UART number to use for console"
	default 0x0
	depends on INTEL_PCH_UART_CONSOLE

config TTYS0_BASE
	hex
	default 0xd6000000
	depends on INTEL_PCH_UART_CONSOLE

config EHCI_BAR
	hex
	default 0xd8000000

config SERIRQ_CONTINUOUS_MODE
	bool
	default y
	help
	  If you set this option to y, the serial IRQ machine will be
	  operated in continuous mode.

config HAVE_REFCODE_BLOB
	depends on ARCH_X86
	bool "An external reference code blob should be put into cbfs."
	default n
	help
	 The reference code blob will be placed into cbfs.

if HAVE_REFCODE_BLOB

config REFCODE_BLOB_FILE
	string "Path and filename to reference code blob."
	default "refcode.elf"
	help
	 The path and filename to the file to be added to cbfs.

endif # HAVE_REFCODE_BLOB

endif