src/mainboard/google/poppy/variants/nautilus/devicetree.cb

chip soc/intel/skylake

	# IGD Displays
	register "gfx" = "GMA_STATIC_DISPLAYS(0)"

	# Deep Sx states
	register "deep_s3_enable_ac" = "0"
	register "deep_s3_enable_dc" = "0"
	register "deep_s5_enable_ac" = "1"
	register "deep_s5_enable_dc" = "1"
	register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN | DSX_EN_WAKE_PIN | DSX_DIS_AC_PRESENT_PD"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route. i.e. If this route changes then the affected GPE
	# offset bits also need to be changed.
	register "gpe0_dw0" = "GPP_B"
	register "gpe0_dw1" = "GPP_D"
	register "gpe0_dw2" = "GPP_E"

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"
	# EC memory map range is 0x900-0x9ff
	register "gen3_dec" = "0x00fc0901"

	# Enable DPTF
	register "dptf_enable" = "1"

	# Enable S0ix
	register "s0ix_enable" = "1"

	# FSP Configuration
	register "ProbelessTrace" = "0"
	register "EnableLan" = "0"
	register "EnableSata" = "0"
	register "SataSalpSupport" = "0"
	register "SataMode" = "0"
	register "SataPortsEnable[0]" = "0"
	register "EnableAzalia" = "1"
	register "DspEnable" = "1"
	register "IoBufferOwnership" = "3"
	register "EnableTraceHub" = "0"
	register "SsicPortEnable" = "0"
	register "SmbusEnable" = "1"
	register "Cio2Enable" = "1"
	register "SaImguEnable" = "1"
	register "ScsEmmcEnabled" = "1"
	register "ScsEmmcHs400Enabled" = "1"
	register "ScsSdCardEnabled" = "2"
	register "PttSwitch" = "0"
	register "SkipExtGfxScan" = "1"
	register "Device4Enable" = "1"
	register "HeciEnabled" = "0"
	register "SaGv" = "3"
	register "PmConfigSlpS3MinAssert" = "2"        # 50ms
	register "PmConfigSlpS4MinAssert" = "1"        # 1s
	register "PmConfigSlpSusMinAssert" = "1"       # 500ms
	register "PmConfigSlpAMinAssert" = "3"         # 2s
	register "PmTimerDisabled" = "1"

	register "pirqa_routing" = "PCH_IRQ11"
	register "pirqb_routing" = "PCH_IRQ10"
	register "pirqc_routing" = "PCH_IRQ11"
	register "pirqd_routing" = "PCH_IRQ11"
	register "pirqe_routing" = "PCH_IRQ11"
	register "pirqf_routing" = "PCH_IRQ11"
	register "pirqg_routing" = "PCH_IRQ11"
	register "pirqh_routing" = "PCH_IRQ11"

	# VR Slew rate setting for improving audible noise
	register "AcousticNoiseMitigation" = "1"
	register "FastPkgCRampDisableIa" = "1"
	register "FastPkgCRampDisableGt" = "1"
	register "FastPkgCRampDisableSa" = "1"
	register "SlowSlewRateForIa" = "3"      # Fast/16
	register "SlowSlewRateForGt" = "3"      # Fast/16
	register "SlowSlewRateForSa" = "2"      # Fast/8

	# VR Settings Configuration for 4 Domains
	#+----------------+-------+-------+-------+-------+
	#| Domain/Setting |  SA   |  IA   | GTUS  |  GTS  |
	#+----------------+-------+-------+-------+-------+
	#| Psi1Threshold  | 20A   | 20A   | 20A   | 20A   |
	#| Psi2Threshold  | 2A    | 2A    | 2A    | 2A    |
	#| Psi3Threshold  | 1A    | 1A    | 1A    | 1A    |
	#| Psi3Enable     | 1     | 1     | 1     | 1     |
	#| Psi4Enable     | 1     | 1     | 1     | 1     |
	#| ImonSlope      | 0     | 0     | 0     | 0     |
	#| ImonOffset     | 0     | 0     | 0     | 0     |
	#| IccMax         | 5A    | 24A   | 24A   | 24A   |
	#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
	#| AcLoadline     | 15    | 5.7   | 5.5   | 5.5   |
	#| DcLoadline     | 14.3  | 4.83  | 4.2   | 4.2   |
	#+----------------+-------+-------+-------+-------+
	register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(5),
		.voltage_limit = 1520,
		.ac_loadline = 1500,
		.dc_loadline = 1430,
	}"

	register "domain_vr_config[VR_IA_CORE]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(24),
		.voltage_limit = 1520,
		.ac_loadline = 570,
		.dc_loadline = 483,
	}"

	register "domain_vr_config[VR_GT_UNSLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(24),
		.voltage_limit = 1520,
		.ac_loadline = 550,
		.dc_loadline = 420,
	}"

	register "domain_vr_config[VR_GT_SLICED]" = "{
		.vr_config_enable = 1,
		.psi1threshold = VR_CFG_AMP(20),
		.psi2threshold = VR_CFG_AMP(2),
		.psi3threshold = VR_CFG_AMP(1),
		.psi3enable = 1,
		.psi4enable = 1,
		.imon_slope = 0x0,
		.imon_offset = 0x0,
		.icc_max = VR_CFG_AMP(24),
		.voltage_limit = 1520,
		.ac_loadline = 550,
		.dc_loadline = 420,
	}"

	# Enable Root port 1.
	register "PcieRpEnable[0]" = "1"
	# Enable CLKREQ#
	register "PcieRpClkReqSupport[0]" = "1"
	# RP 1 uses SRCCLKREQ1#
	register "PcieRpClkReqNumber[0]" = "1"
        # RP 1 uses uses CLK SRC 1
        register "PcieRpClkSrcNumber[0]" = "1"
	# RP 1, Enable Advanced Error Reporting
	register "PcieRpAdvancedErrorReporting[0]" = "1"
	# RP 1, Enable Latency Tolerance Reporting Mechanism
	register "PcieRpLtrEnable[0]" = "1"

	register "usb2_ports[0]" = "USB2_PORT_LONG(OC1)"	# Type-C Port 1
	register "usb2_ports[1]" = "USB2_PORT_SHORT(OC2)"	# Type-A Port
	register "usb2_ports[2]" = "USB2_PORT_SHORT(OC_SKIP)"	# Bluetooth
	register "usb2_ports[4]" = "USB2_PORT_LONG(OC0)"	# Type-C Port 2
	register "usb2_ports[6]" = "USB2_PORT_SHORT(OC_SKIP)"	# H1
	register "usb2_ports[8]" = "USB2_PORT_SHORT(OC_SKIP)"	# Camera

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)"	# Type-C Port 1
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)"	# Type-C Port 2
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)"	# Type-A Port
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# LTE module

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| chipset_lockdown  | CHIPSET_LOCKDOWN_COREBOOT |
	#| I2C0              | Touchscreen               |
	#| I2C1              | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#|                   | before memory is up       |
	#| I2C2              | Trackpad                  |
	#| I2C3              | Pen                       |
	#| I2C4              | Camera                    |
	#| I2C5              | Audio                     |
	#| pch_thermal_trip  | PCH Trip Temperature      |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 180,
				.scl_hcnt = 90,
				.sda_hold = 36,
			},
		},
		.i2c[1] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 185,
				.scl_hcnt = 90,
				.sda_hold = 36,
			},
		},
		.i2c[2] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 190,
				.scl_hcnt = 100,
				.sda_hold = 36,
			},
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 185,
				.scl_hcnt = 90,
				.sda_hold = 36,
			},
		},
		.i2c[4] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 190,
				.scl_hcnt = 100,
				.sda_hold = 36,
			},
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 190,
				.scl_hcnt = 100,
				.sda_hold = 36,
			},
		},
		.pch_thermal_trip = 75,
	}"

	# Touch Screen
	register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3"

	# H1
	register "i2c_voltage[1]" = "I2C_VOLTAGE_3V3"

	# Trackpad
	register "i2c_voltage[2]" = "I2C_VOLTAGE_1V8"

	# Pen
	register "i2c_voltage[3]" = "I2C_VOLTAGE_1V8"

	# Camera
	register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8"

	# Audio
	register "i2c_voltage[5]" = "I2C_VOLTAGE_1V8"

	# Must leave UART0 enabled or SD/eMMC will not work as PCI
	register "SerialIoDevMode" = "{
		[PchSerialIoIndexI2C0]  = PchSerialIoPci,
		[PchSerialIoIndexI2C1]  = PchSerialIoPci,
		[PchSerialIoIndexI2C2]  = PchSerialIoPci,
		[PchSerialIoIndexI2C3]  = PchSerialIoPci,
		[PchSerialIoIndexI2C4]  = PchSerialIoPci,
		[PchSerialIoIndexI2C5]  = PchSerialIoPci,
		[PchSerialIoIndexSpi0]  = PchSerialIoDisabled,
		[PchSerialIoIndexSpi1]  = PchSerialIoDisabled,
		[PchSerialIoIndexUart0] = PchSerialIoSkipInit,
		[PchSerialIoIndexUart1] = PchSerialIoDisabled,
		[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
	}"

	register "speed_shift_enable" = "1"
	# PL2 override 15W for KBL-Y
	register "power_limits_config" = "{
		.tdp_pl2_override = 15,
		.psys_pmax = 45,
	}"
	register "tcc_offset" = "10"     # TCC of 90C

	# Use default SD card detect GPIO configuration
	register "sdcard_cd_gpio_default" = "GPP_E15"

	device cpu_cluster 0 on
		device lapic 0 on end
	end
	device domain 0 on
		device pci 00.0 on  end # Host Bridge
		device pci 02.0 on  end # Integrated Graphics Device
		device pci 14.0 on  end # USB xHCI
		device pci 14.1 on  end # USB xDCI (OTG)
		device pci 14.2 on  end # Thermal Subsystem
		device pci 15.0 on
			chip drivers/i2c/hid
				register "generic.hid" = ""SYTS7813""
				register "generic.desc" = ""Synaptics Touchscreen""
				register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)"
				register "generic.probed" = "1"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C22)"
				register "generic.enable_delay_ms" = "45"
				register "generic.has_power_resource" = "1"
				register "generic.disable_gpio_export_in_crs" = "1"
				register "hid_desc_reg_offset" = "0x20"
				device i2c 20 on end
			end
		end # I2C #0
		device pci 15.1 on
			chip drivers/i2c/tpm
				register "hid" = ""GOOG0005""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E0_IRQ)"
				device i2c 50 on end
			end
		end # I2C #1
		device pci 15.2 on
			chip drivers/i2c/generic
				register "hid" = ""STH9321""
				register "name" = ""SEMTECH SX9321""
				register "desc" = ""SAR Proximity Sensor""
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A18_IRQ)"
				register "device_present_gpio" = "GPP_B20"
				device i2c 28 on end
			end
		end # I2C #2
		device pci 15.3 on
			chip drivers/i2c/hid
				register "generic.hid" = ""ACPI0C50""
				register "generic.cid" = ""PNP0C50""
				register "generic.desc" = ""Digitizer device""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A22_IRQ)"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C9)"
				register "generic.has_power_resource" = "1"
				register "generic.disable_gpio_export_in_crs" = "1"
				register "generic.wake" = "GPE0_DW0_21"
				register "hid_desc_reg_offset" = "0x1"
				device i2c 0x9 on end
			end
			chip drivers/generic/gpio_keys
				register "name" = ""PENH""
				register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_B19)"
				register "key.dev_name" = ""EJCT""
				register "key.linux_code" = "SW_PEN_INSERTED"
				register "key.linux_input_type" = "EV_SW"
				register "key.label" = ""pen_eject""
				device generic 0 on end
			end
		end # I2C #3
		device pci 16.0 on  end # Management Engine Interface 1
		device pci 16.1 off end # Management Engine Interface 2
		device pci 16.2 off end # Management Engine IDE-R
		device pci 16.3 off end # Management Engine KT Redirection
		device pci 16.4 off end # Management Engine Interface 3
		device pci 17.0 off end # SATA
		device pci 19.0 on  end # UART #2
		device pci 19.1 on
			chip drivers/generic/max98357a
				register "hid" = ""MX98357A""
				register "sdmode_gpio" =  "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A23)"
				register "sdmode_delay" = "5"
				device generic 0 on end
			end
			chip drivers/i2c/da7219
				register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D9_IRQ)"
				register "btn_cfg" = "50"
				register "mic_det_thr" = "500"
				register "jack_ins_deb" = "20"
				register "jack_det_rate" = ""32ms_64ms""
				register "jack_rem_deb" = "1"
				register "a_d_btn_thr" = "0xa"
				register "d_b_btn_thr" = "0x16"
				register "b_c_btn_thr" = "0x21"
				register "c_mic_btn_thr" = "0x3e"
				register "btn_avg" = "4"
				register "adc_1bit_rpt" = "1"
				register "micbias_lvl" = "2600"
				register "mic_amp_in_sel" = ""diff""
				device i2c 1A on end
			end
		end # I2C #5
		device pci 19.2 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
				register "wake" = "GPE0_DW0_05"
			device i2c 15 on end
			end
		end # I2C #4
		device pci 1c.0 on
			chip drivers/intel/wifi
				register "wake" = "GPE0_DW0_00"
				device pci 00.0 on end
			end
		end # PCI Express Port 1
		device pci 1c.1 off end # PCI Express Port 2
		device pci 1c.2 off end # PCI Express Port 3
		device pci 1c.3 off end # PCI Express Port 4
		device pci 1c.4 off end # PCI Express Port 5
		device pci 1c.5 off end # PCI Express Port 6
		device pci 1c.6 off end # PCI Express Port 7
		device pci 1c.7 off end # PCI Express Port 8
		device pci 1d.0 off end # PCI Express Port 9
		device pci 1d.1 off end # PCI Express Port 10
		device pci 1d.2 off end # PCI Express Port 11
		device pci 1d.3 off end # PCI Express Port 12
		device pci 1e.0 on  end # UART #0
		device pci 1e.1 off end # UART #1
		device pci 1e.2 off end # GSPI #0
		device pci 1e.3 off end # GSPI #1
		device pci 1e.4 on  end # eMMC
		device pci 1e.5 off end # SDIO
		device pci 1e.6 on end # SDCard
		device pci 1f.0 on
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end # LPC Interface
		device pci 1f.1 on  end # P2SB
		device pci 1f.2 on  end # Power Management Controller
		device pci 1f.3 on  end # Intel HDA
		device pci 1f.4 on  end # SMBus
		device pci 1f.5 on  end # PCH SPI
		device pci 1f.6 off end # GbE
	end
end