src/soc/intel/broadwell/Kconfig

config SOC_INTEL_BROADWELL
	bool
	help
	  Intel Broadwell and Haswell ULT support.

if SOC_INTEL_BROADWELL

config CPU_SPECIFIC_OPTIONS
	def_bool y
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select ARCH_BOOTBLOCK_X86_32
	select ARCH_VERSTAGE_X86_32
	select ARCH_ROMSTAGE_X86_32
	select ARCH_RAMSTAGE_X86_32
	select BOOT_DEVICE_SUPPORTS_WRITES
	select CACHE_MRC_SETTINGS
	select MRC_SETTINGS_PROTECT
	select CPU_INTEL_COMMON
	select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
	select SUPPORT_CPU_UCODE_IN_CBFS
	select HAVE_SMI_HANDLER
	select SOUTHBRIDGE_INTEL_COMMON_RESET
	select SOUTHBRIDGE_INTEL_COMMON_RTC
	select SOUTHBRIDGE_INTEL_COMMON_SMBUS
	select SOUTHBRIDGE_INTEL_COMMON_SPI_ICH9
	select HAVE_USBDEBUG
	select IOAPIC
	select REG_SCRIPT
	select PARALLEL_MP
	select RTC
	select SMP
	select SPI_FLASH
	select SSE2
	select TSC_SYNC_MFENCE
	select UDELAY_TSC
	select TSC_MONOTONIC_TIMER
	select SOC_INTEL_COMMON
	select SOC_INTEL_COMMON_BLOCK
	select SOC_INTEL_COMMON_BLOCK_CPU
	select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE
	select HAVE_SPI_CONSOLE_SUPPORT
	select INTEL_GMA_ACPI
	select HAVE_POWER_STATE_AFTER_FAILURE
	select HAVE_POWER_STATE_PREVIOUS_AFTER_FAILURE
	select NO_FIXED_XIP_ROM_SIZE

config PCIEXP_ASPM
	bool
	default y

config PCIEXP_AER
	bool
	default y

config PCIEXP_COMMON_CLOCK
	bool
	default y

config PCIEXP_CLK_PM
	bool
	default y

config PCIEXP_L1_SUB_STATE
	bool
	default y

config BROADWELL_VBOOT_IN_BOOTBLOCK
	depends on VBOOT
	bool "Start verstage in bootblock"
	default y
	select VBOOT_STARTS_IN_BOOTBLOCK
	select VBOOT_SEPARATE_VERSTAGE
	help
	  Broadwell can either start verstage in a separate stage
	  right after the bootblock has run or it can start it
	  after romstage for compatibility reasons.
	  Broadwell however uses a mrc.bin to initialse memory which
	  needs to be located at a fixed offset. Therefore even with
	  a separate verstage starting after the bootblock that same
	  binary is used meaning a jump is made from RW to the RO region
	  and back to the RW region after the binary is done.

config VBOOT
	select VBOOT_MUST_REQUEST_DISPLAY
	select VBOOT_STARTS_IN_ROMSTAGE if !BROADWELL_VBOOT_IN_BOOTBLOCK

config MMCONF_BASE_ADDRESS
	hex
	default 0xf0000000

config SMM_TSEG_SIZE
	hex
	default 0x800000

config IED_REGION_SIZE
	hex
	default 0x400000

config SMM_RESERVED_SIZE
	hex
	default 0x100000

config VGA_BIOS_ID
	string
	default "8086,0406"

config DCACHE_RAM_BASE
	hex
	default 0xff7c0000

config DCACHE_RAM_SIZE
	hex
	default 0x10000
	help
	  The size of the cache-as-ram region required during bootblock
	  and/or romstage. Note DCACHE_RAM_SIZE and DCACHE_RAM_MRC_VAR_SIZE
	  must add up to a power of 2.

config DCACHE_RAM_MRC_VAR_SIZE
	hex
	default 0x30000
	help
	  The amount of cache-as-ram region required by the reference code.

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x2000
	help
	  The amount of anticipated stack usage in CAR by bootblock and
	  other stages.

config HAVE_MRC
	bool "Add a Memory Reference Code binary"
	help
	  Select this option to add a Memory Reference Code binary to
	  the resulting coreboot image.

	  Note: Without this binary coreboot will not work

if HAVE_MRC

config MRC_FILE
	string "Intel Memory Reference Code path and filename"
	depends on HAVE_MRC
	default "mrc.bin"
	help
	  The filename of the file to use as Memory Reference Code binary.

config MRC_BIN_ADDRESS
	hex
	default 0xfffa0000

# The UEFI System Agent binary needs to be at a fixed offset in the flash
# and can therefore only reside in the COREBOOT fmap region
config RO_REGION_ONLY
	string
	depends on VBOOT
	default "mrc.bin"

endif # HAVE_MRC

config PRE_GRAPHICS_DELAY
	int "Graphics initialization delay in ms"
	default 0
	help
	  On some systems, coreboot boots so fast that connected monitors
	  (mostly TVs) won't be able to wake up fast enough to talk to the
	  VBIOS. On those systems we need to wait for a bit before executing
	  the VBIOS.

config INTEL_PCH_UART_CONSOLE
	bool "Use Serial IO UART for console"
	default n
	select DRIVERS_UART_8250MEM

config INTEL_PCH_UART_CONSOLE_NUMBER
	hex "Serial IO UART number to use for console"
	default 0x0
	depends on INTEL_PCH_UART_CONSOLE

config TTYS0_BASE
	hex
	default 0xd6000000
	depends on INTEL_PCH_UART_CONSOLE

config EHCI_BAR
	hex
	default 0xd8000000

config SERIRQ_CONTINUOUS_MODE
	bool
	default y
	help
	  If you set this option to y, the serial IRQ machine will be
	  operated in continuous mode.

config HAVE_REFCODE_BLOB
	depends on ARCH_X86
	bool "An external reference code blob should be put into cbfs."
	default n
	help
	 The reference code blob will be placed into cbfs.

if HAVE_REFCODE_BLOB

config REFCODE_BLOB_FILE
	string "Path and filename to reference code blob."
	default "refcode.elf"
	help
	 The path and filename to the file to be added to cbfs.

endif # HAVE_REFCODE_BLOB

endif