src/mainboard/lenovo/t520/devicetree.cb

chip northbridge/intel/sandybridge

	# Enable DisplayPort Hotplug with 6ms pulse
	register "gpu_dp_d_hotplug" = "0x06"

	# Enable Panel as LVDS and configure power delays
	register "gpu_panel_port_select" = "0"			# LVDS
	register "gpu_panel_power_cycle_delay" = "5"
	register "gpu_panel_power_up_delay" = "300"		# T1+T2: 30ms
	register "gpu_panel_power_down_delay" = "300"		# T5+T6: 30ms
	register "gpu_panel_power_backlight_on_delay" = "2000"	# T3: 200ms
	register "gpu_panel_power_backlight_off_delay" = "2000"	# T4: 200ms
	register "gfx.use_spread_spectrum_clock" = "1"
	register "gfx.lvds_dual_channel" = "1"
	register "gfx.link_frequency_270_mhz" = "1"
	register "gfx.lvds_num_lanes" = "4"
	register "gpu_cpu_backlight" = "0x1155"
	register "gpu_pch_backlight" = "0x06100610"

	device cpu_cluster 0 on
		chip cpu/intel/socket_rPGA988B
			device lapic 0 on end
		end
		chip cpu/intel/model_206ax
			# Magic APIC ID to locate this chip
			device lapic 0xACAC off end

			# Coordinate with HW_ALL
			register "pstate_coord_type" = "0xfe"

			register "c1_acpower" = "1"	# ACPI(C1) = MWAIT(C1)
			register "c2_acpower" = "3"	# ACPI(C2) = MWAIT(C3)
			register "c3_acpower" = "5"	# ACPI(C3) = MWAIT(C7)

			register "c1_battery" = "1"	# ACPI(C1) = MWAIT(C1)
			register "c2_battery" = "3"	# ACPI(C2) = MWAIT(C3)
			register "c3_battery" = "5"	# ACPI(C3) = MWAIT(C7)
		end
	end

	device domain 0 on
		device pci 00.0 on end # host bridge
		device pci 01.0 on end # NVIDIA Corporation GF119M [NVS 4200M]
		device pci 02.0 on end # vga controller

		chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH
			# GPI routing
			#  0 No effect (default)
			#  1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set)
			#  2 SCI (if corresponding GPIO_EN bit is also set)
			register "alt_gp_smi_en" = "0x0000"
			register "gpi1_routing" = "2"
			register "gpi13_routing" = "2"

			# Enable SATA ports 0 (HDD bay) & 1 (ODD bay) & 2 (mSATA) & 3 (eSATA) & 4 (dock)
			register "sata_port_map" = "0x1f"
			# Set max SATA speed to 6.0 Gb/s
			register "sata_interface_speed_support" = "0x3"

			register "gen1_dec" = "0x7c1601"
			register "gen2_dec" = "0x0c15e1"
			register "gen4_dec" = "0x0c06a1"

			# Enable zero-based linear PCIe root port functions
			register "pcie_port_coalesce" = "1"

			register "c2_latency" = "101"  # c2 not supported
			register "p_cnt_throttling_supported" = "1"

			register "pcie_hotplug_map" = "{ 0, 0, 0, 1, 0, 0, 0, 0 }"

			device pci 16.0 on end # Management Engine Interface 1
			device pci 16.1 off end
			device pci 16.2 off end
			device pci 16.3 off end
			device pci 19.0 on end # Intel Gigabit Ethernet
			device pci 1a.0 on end # USB2 EHCI #2
			device pci 1b.0 on end # High Definition Audio
			device pci 1c.0 off end # PCIe Port #1
			device pci 1c.1 on end # PCIe Port #2 Integrated Wireless LAN
			device pci 1c.2 off end # PCIe Port #3
			device pci 1c.3 on end # PCIe Port #4 Express Card
			device pci 1c.4 on end # PCIe Port #5 MMC/SDXC + IEEE1394
			device pci 1c.5 off end # PCIe Port #6 Intel Ethernet PHY
			device pci 1c.6 off end # PCIe Port #7 USB 3.0 only W520
			device pci 1c.7 off end # PCIe Port #8
			device pci 1d.0 on end # USB2 EHCI #1
			device pci 1f.0 on #LPC bridge
				chip ec/lenovo/pmh7
					device pnp ff.1 on # dummy
					end
					register "backlight_enable" = "0x01"
					register "dock_event_enable" = "0x01"
				end

				chip ec/lenovo/h8
					device pnp ff.2 on # dummy
						io 0x60 = 0x62
						io 0x62 = 0x66
						io 0x64 = 0x1600
						io 0x66 = 0x1604
					end

					register "config0" = "0xa7"
					register "config1" = "0x09"
					register "config2" = "0xa0"
					register "config3" = "0xc2"

					register "beepmask0" = "0x00"
					register "beepmask1" = "0x86"
					register "has_power_management_beeps" = "0"
					register "event2_enable" = "0xff"
					register "event3_enable" = "0xff"
					register "event4_enable" = "0xd0"
					register "event5_enable" = "0xfc"
					register "event6_enable" = "0x00"
					register "event7_enable" = "0x01"
					register "event8_enable" = "0x7b"
					register "event9_enable" = "0xff"
					register "eventa_enable" = "0x01"
					register "eventb_enable" = "0x00"
					register "eventc_enable" = "0xff"
					register "eventd_enable" = "0xff"
					register "evente_enable" = "0x0d"
				end
			end # LPC bridge
			device pci 1f.2 on end # SATA Controller 1
			device pci 1f.3 on # SMBUS controller
			        # eeprom, 8 virtual devices, same chip
				chip drivers/i2c/at24rf08c
					device i2c 54 on end
					device i2c 55 on end
					device i2c 56 on end
					device i2c 57 on end
					device i2c 5c on end
					device i2c 5d on end
					device i2c 5e on end
					device i2c 5f on end
				end
			end # SMBus
		end
	end
end