src/southbridge/amd/pi/hudson/hudson.h

/* SPDX-License-Identifier: GPL-2.0-only */

#ifndef HUDSON_H
#define HUDSON_H

#include <types.h>
#include <device/device.h>

/* Offsets from ACPI_MMIO_BASE
 * This is defined by AGESA, but we don't include AGESA headers to avoid
 * polluting the namespace.
 */
#define PM_MMIO_BASE			0xfed80300

/* Power management index/data registers */
#define BIOSRAM_INDEX			0xcd4
#define BIOSRAM_DATA			0xcd5
#define PM_INDEX			0xcd6
#define PM_DATA				0xcd7
#define PM2_INDEX			0xcd0
#define PM2_DATA			0xcd1

#define PM_ACPI_MMIO_EN			0x24
#define PM_SERIRQ_CONF			0x54
#define PM_EVT_BLK			0x60
#define PM1_CNT_BLK			0x62
#define PM_TMR_BLK			0x64
#define PM_CPU_CTRL			0x66
#define PM_GPE0_BLK			0x68
#define PM_ACPI_SMI_CMD			0x6A
#define PM_ACPI_CONF			0x74
#define PM_PMIO_DEBUG			0xD2
#define PM_MANUAL_RESET			0xD3
#define PM_HUD_SD_FLASH_CTRL		0xE7
#define PM_YANG_SD_FLASH_CTRL		0xE8
#define PM_PCIB_CFG			0xEA

#define HUDSON_ACPI_IO_BASE		CONFIG_HUDSON_ACPI_IO_BASE
#define ACPI_PM_EVT_BLK		(HUDSON_ACPI_IO_BASE + 0x00) /* 4 bytes */
#define ACPI_PM1_CNT_BLK	(HUDSON_ACPI_IO_BASE + 0x04) /* 2 bytes */
#define ACPI_PM_TMR_BLK		(HUDSON_ACPI_IO_BASE + 0x18) /* 4 bytes */
#define ACPI_GPE0_BLK		(HUDSON_ACPI_IO_BASE + 0x10) /* 8 bytes */
#define ACPI_CPU_CONTROL	(HUDSON_ACPI_IO_BASE + 0x08) /* 6 bytes */

#define ACPI_SCI_IRQ			9

#define ACPI_SMI_CTL_PORT		0xb2

#define REV_HUDSON_A11			0x11
#define REV_HUDSON_A12			0x12

#define SPIROM_BASE_ADDRESS_REGISTER	0xA0
#define   ROUTE_TPM_2_SPI		BIT(3)
#define   SPI_ROM_ENABLE		0x02
#define   SPI_BASE_ADDRESS		0xFEC10000

#define LPC_IO_PORT_DECODE_ENABLE	0x44
#define   DECODE_ENABLE_PARALLEL_PORT0	BIT(0)
#define   DECODE_ENABLE_PARALLEL_PORT1	BIT(1)
#define   DECODE_ENABLE_PARALLEL_PORT2	BIT(2)
#define   DECODE_ENABLE_PARALLEL_PORT3	BIT(3)
#define   DECODE_ENABLE_PARALLEL_PORT4	BIT(4)
#define   DECODE_ENABLE_PARALLEL_PORT5	BIT(5)
#define   DECODE_ENABLE_SERIAL_PORT0	BIT(6)
#define   DECODE_ENABLE_SERIAL_PORT1	BIT(7)
#define   DECODE_ENABLE_SERIAL_PORT2	BIT(8)
#define   DECODE_ENABLE_SERIAL_PORT3	BIT(9)
#define   DECODE_ENABLE_SERIAL_PORT4	BIT(10)
#define   DECODE_ENABLE_SERIAL_PORT5	BIT(11)
#define   DECODE_ENABLE_SERIAL_PORT6	BIT(12)
#define   DECODE_ENABLE_SERIAL_PORT7	BIT(13)
#define   DECODE_ENABLE_AUDIO_PORT0	BIT(14)
#define   DECODE_ENABLE_AUDIO_PORT1	BIT(15)
#define   DECODE_ENABLE_AUDIO_PORT2	BIT(16)
#define   DECODE_ENABLE_AUDIO_PORT3	BIT(17)
#define   DECODE_ENABLE_MIDI_PORT0	BIT(18)
#define   DECODE_ENABLE_MIDI_PORT1	BIT(19)
#define   DECODE_ENABLE_MIDI_PORT2	BIT(20)
#define   DECODE_ENABLE_MIDI_PORT3	BIT(21)
#define   DECODE_ENABLE_MSS_PORT0	BIT(22)
#define   DECODE_ENABLE_MSS_PORT1	BIT(23)
#define   DECODE_ENABLE_MSS_PORT2	BIT(24)
#define   DECODE_ENABLE_MSS_PORT3	BIT(25)
#define   DECODE_ENABLE_FDC_PORT0	BIT(26)
#define   DECODE_ENABLE_FDC_PORT1	BIT(27)
#define   DECODE_ENABLE_GAME_PORT	BIT(28)
#define   DECODE_ENABLE_KBC_PORT	BIT(29)
#define   DECODE_ENABLE_ACPIUC_PORT	BIT(30)
#define   DECODE_ENABLE_ADLIB_PORT	BIT(31)

#define LPC_IO_OR_MEM_DECODE_ENABLE	0x48
#define   LPC_WIDEIO2_ENABLE		BIT(25)
#define   LPC_WIDEIO1_ENABLE		BIT(24)
#define   LPC_WIDEIO0_ENABLE		BIT(2)

#define LPC_WIDEIO_GENERIC_PORT		0x64

#define LPC_ALT_WIDEIO_RANGE_ENABLE	0x74
#define   LPC_ALT_WIDEIO2_ENABLE	BIT(3)
#define   LPC_ALT_WIDEIO1_ENABLE	BIT(2)
#define   LPC_ALT_WIDEIO0_ENABLE	BIT(0)

#define LPC_TRUSTED_PLATFORM_MODULE	0x7c
#define   TPM_12_EN			BIT(0)
#define   TPM_LEGACY_EN			BIT(2)

#define LPC_WIDEIO2_GENERIC_PORT	0x90

#define SPI_CNTRL0			0x00
#define   SPI_READ_MODE_MASK		(BIT(30) | BIT(29) | BIT(18))
/* Nominal is 16.7MHz on older devices, 33MHz on newer */
#define   SPI_READ_MODE_NOM		0x00000000
#define   SPI_READ_MODE_DUAL112		(          BIT(29)          )
#define   SPI_READ_MODE_QUAD114		(          BIT(29) | BIT(18))
#define   SPI_READ_MODE_DUAL122		(BIT(30)                    )
#define   SPI_READ_MODE_QUAD144		(BIT(30) |           BIT(18))
#define   SPI_READ_MODE_NORMAL66	(BIT(30) | BIT(29)          )
/* Nominal and SPI_READ_MODE_FAST_HUDSON1 are the only valid choices for H1 */
#define   SPI_READ_MODE_FAST_HUDSON1	(                    BIT(18))
#define   SPI_READ_MODE_FAST		(BIT(30) | BIT(29) | BIT(18))
#define   SPI_ARB_ENABLE		BIT(19)

#define SPI_CNTRL1			0x0c
/* Use SPI_SPEED_16M-SPI_SPEED_66M below for hudson and bolton */
#define   SPI_CNTRL1_SPEED_MASK	(BIT(15) | BIT(14) | BIT(13) | BIT(12))
#define   SPI_NORM_SPEED_SH		12
#define   SPI_FAST_SPEED_SH		8

#define SPI100_ENABLE			0x20
#define   SPI_USE_SPI100		BIT(0)

#define SPI100_SPEED_CONFIG		0x22
#define   SPI_SPEED_66M			(0x0)
#define   SPI_SPEED_33M			(                  BIT(0))
#define   SPI_SPEED_22M			(         BIT(1)         )
#define   SPI_SPEED_16M			(         BIT(1) | BIT(0))
#define   SPI_SPEED_100M		(BIT(2)                  )
#define   SPI_SPEED_800K		(BIT(2) |          BIT(0))
#define   SPI_NORM_SPEED_NEW_SH		12
#define   SPI_FAST_SPEED_NEW_SH		8
#define   SPI_ALT_SPEED_NEW_SH		4
#define   SPI_TPM_SPEED_NEW_SH		0

#define SPI100_HOST_PREF_CONFIG	0x2c
#define   SPI_RD4DW_EN_HOST		BIT(15)

static inline int hudson_sata_enable(void)
{
	/* True if IDE or AHCI. */
	return (CONFIG_HUDSON_SATA_MODE == 0) || (CONFIG_HUDSON_SATA_MODE == 2);
}

static inline int hudson_ide_enable(void)
{
	/* True if IDE or LEGACY IDE. */
	return (CONFIG_HUDSON_SATA_MODE == 0) || (CONFIG_HUDSON_SATA_MODE == 3);
}

void hudson_lpc_port80(void);
void hudson_lpc_decode(void);
void hudson_pci_port80(void);
void hudson_clk_output_48Mhz(void);
void hudson_read_mode(u32 mode);
void hudson_set_spi100(u16 norm, u16 fast, u16 alt, u16 tpm);
void hudson_disable_4dw_burst(void);
void hudson_set_readspeed(u16 norm, u16 fast);
void lpc_wideio_512_window(uint16_t base);
void lpc_wideio_16_window(uint16_t base);
void hudson_tpm_decode_spi(void);

void hudson_enable(struct device *dev);
void s3_resume_init_data(void *FchParams);

#endif /* HUDSON_H */