src/mainboard/google/brya/variants/orisa/overridetree.cb

fw_config
	field THERMAL_SOLUTION 0 0
		option THERMAL_SOLUTION_6W 0
		option THERMAL_SOLUTION_15W 1
	end
	field STORAGE 30 31
		option STORAGE_EMMC		0
		option STORAGE_UFS		1
	end
end

chip soc/intel/alderlake
	register "sagv" = "SaGv_Enabled"

	# GPE configuration
	register "pmc_gpe0_dw1" = "GPP_B"

	# S0ix enable
	register "s0ix_enable" = "1"

	# DPTF enable
	register "dptf_enable" = "1"

	register "tcc_offset" = "10"     # TCC of 90

	# Enable CNVi BT
	register "cnvi_bt_core" = "true"

	# eMMC HS400
	register "emmc_enable_hs400_mode" = "1"

	#eMMC DLL tuning parameters
	# EMMC Tx CMD Delay
	# Refer to EDS-Vol2-42.3.7.
	# [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39.
	# [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39.
	register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505"

	# EMMC TX DATA Delay 1
	# Refer to EDS-Vol2-42.3.8.
	# [14:8] steps of delay for HS400, each 125ps, range: 0 - 78.
	# [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79.
	register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909"

	# EMMC TX DATA Delay 2
	# Refer to EDS-Vol2-42.3.9.
	# [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79.
	# [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
	# [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79.
	# [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79.
	register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828"

	# EMMC RX CMD/DATA Delay 1
	# Refer to EDS-Vol2-42.3.10.
	# [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119.
	# [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
	# [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119.
	# [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119.
	register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B"

	# EMMC RX CMD/DATA Delay 2
	# Refer to EDS-Vol2-42.3.12.
	# [17:16] stands for Rx Clock before Output Buffer,
	#         00: Rx clock after output buffer,
	#         01: Rx clock before output buffer,
	#         10: Automatic selection based on working mode.
	#         11: Reserved
	# [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39.
	# [6:0] steps of delay for HS200, each 125ps, range: 0 - 79.
	register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1004E"

	# EMMC Rx Strobe Delay
	# Refer to EDS-Vol2-42.3.11.
	# [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39.
	# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
	register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515"

	register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)"     # USB2_A0
	register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)"     # USB2_A1
	register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)"     # M.2 Camera
	register "usb2_ports[3]" = "USB2_PORT_EMPTY"            # Disable USB2 Port 4
	register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC_SKIP)"  # USB2_C0
	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)"     # Bluetooth port for CNVi WLAN
	register "usb2_ports[6]" = "USB2_PORT_EMPTY"            # Disable USB2 Port 7
	register "usb2_ports[7]" = "USB2_PORT_EMPTY"            # Disable USB2 Port 8
	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)"     # Bluetooth port for CNVi WLAN

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# USB3/2 Type A port A0
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# USB3/2 Type A port A1

	register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)"

	# Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
	# Bit 2 - C1 has a redriver which does SBU muxing.
	# Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
	register "tcss_aux_ori" = "0"

	# HD Audio
	register "pch_hda_dsp_enable" = "1"
	register "pch_hda_sdi_enable[0]" = "1"
	register "pch_hda_sdi_enable[1]" = "1"
	register "pch_hda_audio_link_hda_enable" = "1"
	register "pch_hda_idisp_link_tmode" = "HDA_TMODE_8T"
	register "pch_hda_idisp_link_frequency" = "HDA_LINKFREQ_96MHZ"
	register "pch_hda_idisp_codec_enable" = "1"

	# Configure external V1P05/Vnn/VnnSx Rails
	register "ext_fivr_settings" = "{
		.configure_ext_fivr = 1,
		.v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
		.vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
		.vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
		.v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
		.vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
		.v1p05_voltage_mv = 1050,
		.vnn_voltage_mv = 780,
		.vnn_sx_voltage_mv = 1050,
		.v1p05_icc_max_ma = 500,
		.vnn_icc_max_ma = 500,
	}"


	register "serial_io_i2c_mode" = "{
		[PchSerialIoIndexI2C0] = PchSerialIoPci,
		[PchSerialIoIndexI2C1] = PchSerialIoPci,
		[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C5] = PchSerialIoPci,
	}"

	register "serial_io_gspi_mode" = "{
		[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
		[PchSerialIoIndexGSPI1] = PchSerialIoDisabled,
	}"

	register "serial_io_uart_mode" = "{
		[PchSerialIoIndexUART0] = PchSerialIoPci,
		[PchSerialIoIndexUART1] = PchSerialIoDisabled,
		[PchSerialIoIndexUART2] = PchSerialIoDisabled,
	}"

	# FIXME: To be enabled in future based on PNP impact data.
	# Disable Package C-state demotion for nissa baseboard.
	register "disable_package_c_state_demotion" = "1"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| I2C0              | TPM. Early init is        |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#| I2C1              | Trackpad                  |
	#| I2C5              | Touchscreen               |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST_PLUS,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST_PLUS,
				.scl_lcnt = 55,
				.scl_hcnt = 30,
				.sda_hold = 7,
			}
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 158,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 158,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
	}"

	register "power_limits_config[ADL_N_041_6W_CORE]" = "{
		.tdp_pl1_override = 20,
		.tdp_pl2_override = 25,
		.tdp_pl4 = 78,
	}"

	register "power_limits_config[ADL_N_081_15W_CORE]" = "{
		.tdp_pl1_override = 20,
		.tdp_pl2_override = 35,
		.tdp_pl4 = 83,
	}"

	device domain 0 on
		device ref igpu on end
		device ref dtt on
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""DDR""
				register "options.tsr[1].desc" = ""charger""
				register "options.tsr[2].desc" = ""ambient""

				## Active Policy
				register "policies.active" = "{
					[0] = {
						.target = DPTF_CPU,
						.thresholds = {
								TEMP_PCT(70, 100),
								TEMP_PCT(60, 65),
								TEMP_PCT(42, 60),
								TEMP_PCT(39, 55),
								TEMP_PCT(38, 50),
								TEMP_PCT(35, 43),
								TEMP_PCT(31, 30),
						}
					},
					[1] = {
						.target = DPTF_TEMP_SENSOR_0,
						.thresholds = {
								TEMP_PCT(60, 100),
								TEMP_PCT(55, 65),
								TEMP_PCT(52, 60),
								TEMP_PCT(50, 55),
								TEMP_PCT(48, 50),
								TEMP_PCT(45, 43),
								TEMP_PCT(41, 30),
						}
					}
				}"

				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           95, 5000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 70, 5000),
					[2] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_1, 70, 5000),
					[3] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_2, 70, 5000),
				}"

				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               100, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,     95, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,     95, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,     95, SHUTDOWN),
				}"

				register "controls.power_limits" = "{
					.pl1 = {
						.min_power = 6000,
						.max_power = 20000,
						.time_window_min = 28 * MSECS_PER_SEC,
						.time_window_max = 28 * MSECS_PER_SEC,
						.granularity = 500
					},
					.pl2 = {
						.min_power = 25000,
						.max_power = 25000,
						.time_window_min = 32 * MSECS_PER_SEC,
						.time_window_max = 32 * MSECS_PER_SEC,
						.granularity = 500
					}
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"

				## Fan Performance Control (Percent, Speed, Noise, Power)
				register "controls.fan_perf" = "{
					[0] = { 100, 6000, 220, 2200, },
					[1] = {  92, 5500, 180, 1800, },
					[2] = {  85, 5000, 145, 1450, },
					[3] = {  70, 4400, 115, 1150, },
					[4] = {  56, 3900,  90,  900, },
					[5] = {  45, 3300,  55,  550, },
					[6] = {  38, 3000,  30,  300, },
					[7] = {  33, 2900,  15,  150, },
					[8] = {  10,  800,  10,  100, },
					[9] = {   0,    0,   0,   50, }
				}"

				## Fan options
				register "options.fan.fine_grained_control" = "1"
				register "options.fan.step_size" = "2"

				device generic 0 on
					probe THERMAL_SOLUTION THERMAL_SOLUTION_6W
				end
			end
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""DDR""
				register "options.tsr[1].desc" = ""charger""
				register "options.tsr[2].desc" = ""ambient""

				## Active Policy
				register "policies.active" = "{
					[0] = {
						.target = DPTF_CPU,
						.thresholds = {
								TEMP_PCT(70, 100),
								TEMP_PCT(60, 65),
								TEMP_PCT(42, 58),
								TEMP_PCT(39, 53),
								TEMP_PCT(38, 47),
								TEMP_PCT(35, 43),
								TEMP_PCT(31, 30),
						}
					},
					[1] = {
						.target = DPTF_TEMP_SENSOR_0,
						.thresholds = {
								TEMP_PCT(60, 100),
								TEMP_PCT(55, 65),
								TEMP_PCT(52, 58),
								TEMP_PCT(50, 53),
								TEMP_PCT(48, 47),
								TEMP_PCT(45, 43),
								TEMP_PCT(41, 30),
						}
					}
				}"

				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           95, 5000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 70, 5000),
					[2] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_1, 70, 5000),
					[3] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_2, 70, 5000),
				}"

				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               100, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,     95, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,     95, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,     95, SHUTDOWN),
				}"

				register "controls.power_limits" = "{
					.pl1 = {
						.min_power = 15000,
						.max_power = 20000,
						.time_window_min = 28 * MSECS_PER_SEC,
						.time_window_max = 28 * MSECS_PER_SEC,
						.granularity = 500
					},
					.pl2 = {
						.min_power = 35000,
						.max_power = 35000,
						.time_window_min = 32 * MSECS_PER_SEC,
						.time_window_max = 32 * MSECS_PER_SEC,
						.granularity = 500
					}
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"

				## Fan Performance Control (Percent, Speed, Noise, Power)
				register "controls.fan_perf" = "{
					[0] = { 100, 6000, 220, 2200, },
					[1] = {  92, 5500, 180, 1800, },
					[2] = {  85, 5000, 145, 1450, },
					[3] = {  70, 4400, 115, 1150, },
					[4] = {  56, 3900,  90,  900, },
					[5] = {  45, 3300,  55,  550, },
					[6] = {  38, 3000,  30,  300, },
					[7] = {  33, 2900,  15,  150, },
					[8] = {  10,  800,  10,  100, },
					[9] = {   0,    0,   0,   50, }
				}"

				## Fan options
				register "options.fan.fine_grained_control" = "1"
				register "options.fan.step_size" = "2"

				device generic 1 on
					probe THERMAL_SOLUTION THERMAL_SOLUTION_15W
				end
			end
		end
		device ref tcss_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref tcss_usb3_port1 on end
					end
				end
			end
		end
		device ref xhci on
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref usb2_port5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A0 (DB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
						device ref usb2_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Camera""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =	"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A0 (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
						device ref usb3_port2 on end
					end
				end
			end
		end
		device ref shared_sram on end
		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				register "enable_cnvi_ddr_rfim" = "true"
				register "add_acpi_dma_property" = "true"
				device generic 0 on end
			end
		end
		device ref i2c0 on
			chip drivers/i2c/tpm
				register "hid" = ""GOOG0005""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A17_IRQ)"
				device i2c 50 on end
			end
		end #I2C0
		device ref i2c1 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
				register "wake" = "GPE0_DW1_03"
				register "detect" = "1"
				device i2c 15 on end
			end
		end #I2C1
		device ref i2c5 on
			chip drivers/i2c/hid
				register "generic.hid" = ""ELAN9004""
				register "generic.desc" = ""ELAN Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D16_IRQ)"
				register "generic.detect" = "1"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)"
				register "generic.reset_delay_ms" = "20"
				register "generic.reset_off_delay_ms" = "2"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E17)"
				register "generic.enable_delay_ms" = "1"
				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A21)"
				register "generic.stop_delay_ms" = "150"
				register "generic.stop_off_delay_ms" = "2"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 10 on end
			end
		end #I2C5
		device ref heci1 on end
		device ref pcie_rp7 off end
		device ref emmc on end
		device ref ish on
			chip drivers/intel/ish
				register "add_acpi_dma_property" = "true"
				device generic 0 on end
			end
		end
		device ref ufs on end
		device ref uart0 on end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				device pnp 0c09.0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port5 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
				end
			end
		end
		device ref hda on
			chip drivers/sof
				register "spkr_tplg" = "max98360a"
				register "jack_tplg" = "rt5682"
				register "mic_tplg" = "_2ch_pdm0"
				device generic 0 on end
			end
		end
	end
end