src/soc/intel/denverton_ns/Kconfig

# SPDX-License-Identifier: GPL-2.0-only

config SOC_INTEL_DENVERTON_NS
	bool
	help
	  Intel Denverton-NS SoC support

if SOC_INTEL_DENVERTON_NS

config CPU_SPECIFIC_OPTIONS
	def_bool y
	select ARCH_ALL_STAGES_X86_32
	select BOOT_DEVICE_SUPPORTS_WRITES
	select DEBUG_GPIO
	select SOC_INTEL_COMMON
	select SOC_INTEL_COMMON_RESET
	select PLATFORM_USES_FSP2_0
	select IOAPIC
	select HAVE_INTEL_FSP_REPO
	select HAVE_SMI_HANDLER
	select CACHE_MRC_SETTINGS
	select PARALLEL_MP
	select PCR_COMMON_IOSF_1_0
	select INTEL_DESCRIPTOR_MODE_CAPABLE
	select SOC_INTEL_COMMON_BLOCK
	select SOC_INTEL_COMMON_BLOCK_CPU
	select SOC_INTEL_COMMON_BLOCK_ACPI
	select SOC_INTEL_COMMON_BLOCK_PMC
	select ACPI_INTEL_HARDWARE_SLEEP_VALUES
	select SOC_INTEL_COMMON_BLOCK_FAST_SPI
	select SOC_INTEL_COMMON_BLOCK_GPIO
	select SOC_INTEL_COMMON_BLOCK_PCR
	select TSC_MONOTONIC_TIMER
	select TSC_SYNC_MFENCE
	select UDELAY_TSC
	select UDK_2015_BINDING
	select CPU_INTEL_COMMON
	select CPU_INTEL_FIRMWARE_INTERFACE_TABLE
	select SUPPORT_CPU_UCODE_IN_CBFS

config MMCONF_BASE_ADDRESS
	hex
	default 0xe0000000

config FSP_T_ADDR
	hex "Intel FSP-T (temp RAM init) binary location"
	depends on ADD_FSP_BINARIES && FSP_CAR
	default 0xfff30000
	help
	  The memory location of the Intel FSP-T binary for this platform.

config FSP_M_ADDR
	hex "Intel FSP-M (memory init) binary location"
	depends on ADD_FSP_BINARIES
	default 0xfff32000
	help
	  The memory location of the Intel FSP-M binary for this platform.

config FSP_S_ADDR
	hex "Intel FSP-S (silicon init) binary location"
	depends on ADD_FSP_BINARIES
	default 0xfffc3000
	help
	  The memory location of the Intel FSP-S binary for this platform.

config FSP_HEADER_PATH
	default "3rdparty/fsp/DenvertonNSFspBinPkg/Include/"

config FSP_FD_PATH
	default "3rdparty/fsp/DenvertonNSFspBinPkg/FspBin/DenvertonNSFsp.fd"

# CAR memory layout on DENVERTON_NS hardware:
## CAR base address - 0xfef00000
## CAR size 1MB - 0x100 (0xfff00)
## coreboot usage:
## DCACHE base - 0xfef00000
## DCACHE size - 0xb0000
## FSP usage:
## FSP base - 0xfefb0000
## FSP size - 0x50000 - 0x100 (0x4ff00)
config MAX_CPUS
	int
	default 16

config PCR_BASE_ADDRESS
	hex
	default 0xfd000000
	help
	  This option allows you to select MMIO Base Address of sideband bus.

config DCACHE_RAM_BASE
	hex
	default 0xfef00000

config DCACHE_RAM_SIZE
	hex
	default 0xb0000 if FSP_CAR
	default 0x100000 if !FSP_CAR

config DCACHE_BSP_STACK_SIZE
	hex
	default 0x10000

config CPU_BCLK_MHZ
	int
	default 100

config SMM_TSEG_SIZE
	hex
	default 0x200000

config SMM_RESERVED_SIZE
	hex
	default 0x000000

config IQAT_ENABLE
	bool "Enable IQAT"
	default y

config HSUART_DEV
	hex
	default 0x1a

choice
	prompt "UART mode selection"
	default NON_LEGACY_UART_MODE

config NON_LEGACY_UART_MODE
	bool "Non Legacy Mode"
	help
	  Disable legacy UART mode

config LEGACY_UART_MODE
	bool "Legacy Mode"
	help
	  Enable legacy UART mode
endchoice

config ENABLE_HSUART
	depends on NON_LEGACY_UART_MODE
	bool "Enable High-speed UART debug port selected by UART_FOR_CONSOLE."
	default n
	select CONSOLE_SERIAL
	select DRIVERS_UART
	select DRIVERS_UART_8250MEM

config CONSOLE_UART_BASE_ADDRESS
	depends on ENABLE_HSUART
	hex "MMIO base address for UART"
	default 0xd4000000

config C_ENV_BOOTBLOCK_SIZE
	hex
	default 0x8000

config DENVERTON_NS_CAR_NEM_ENHANCED
	bool "Enhanced Non-evict mode"
	depends on !FSP_CAR
	default y
	select SOC_INTEL_COMMON_BLOCK_CAR
	select USE_CAR_NEM_ENHANCED_V1
	help
	  A current limitation of NEM (Non-Evict mode) is that code and data sizes
	  are derived from the requirement to not write out any modified cache line.
	  With NEM, if there is no physical memory behind the cached area,
	  the modified data will be lost and NEM results will be inconsistent.
	  ENHANCED NEM guarantees that modified data is always
	  kept in cache while clean data is replaced.

endif ## SOC_INTEL_DENVERTON_NS