| /* SPDX-License-Identifier: BSD-3-Clause */ |
| /* coreboot UEFI PEI wrapper */ |
| |
| #ifndef PEI_DATA_H |
| #define PEI_DATA_H |
| |
| #include <stdint.h> |
| |
| typedef struct { |
| uint16_t mode; /* 0: Disable, 1: Enable, 2: Auto, 3: Smart Auto */ |
| uint16_t hs_port_switch_mask; /* 4 bit mask, 1: switchable, 0: not switchable */ |
| uint16_t preboot_support; /* 0: No xHCI preOS driver, 1: xHCI preOS driver */ |
| uint16_t xhci_streams; /* 0: Disable, 1: Enable */ |
| } pch_usb3_controller_settings; |
| |
| typedef void (*tx_byte_func)(unsigned char byte); |
| #define PEI_VERSION 6 |
| |
| struct pei_data |
| { |
| uint32_t pei_version; |
| uint32_t mchbar; |
| uint32_t dmibar; |
| uint32_t epbar; |
| uint32_t pciexbar; |
| uint16_t smbusbar; |
| uint32_t wdbbar; |
| uint32_t wdbsize; |
| uint32_t hpet_address; |
| uint32_t rcba; |
| uint32_t pmbase; |
| uint32_t gpiobase; |
| uint32_t thermalbase; |
| uint32_t system_type; /* 0 Mobile, 1 Desktop/Server */ |
| uint32_t tseg_size; |
| uint8_t spd_addresses[4]; |
| uint8_t ts_addresses[4]; |
| int boot_mode; |
| int ec_present; |
| int gbe_enable; |
| /* |
| * 0 = leave channel enabled |
| * 1 = disable dimm 0 on channel |
| * 2 = disable dimm 1 on channel |
| * 3 = disable dimm 0+1 on channel |
| */ |
| int dimm_channel0_disabled; |
| int dimm_channel1_disabled; |
| /* Seed values saved in CMOS */ |
| uint32_t scrambler_seed; |
| uint32_t scrambler_seed_s3; |
| /* Data read from flash and passed into MRC */ |
| uint32_t mrc_input_ptr; |
| unsigned int mrc_input_len; |
| /* Data from MRC that should be saved to flash */ |
| uint32_t mrc_output_ptr; |
| unsigned int mrc_output_len; |
| /* |
| * Max frequency DDR3 could be ran at. Could be one of four values: |
| * 800, 1067, 1333, 1600 |
| */ |
| uint32_t max_ddr3_freq; |
| /* |
| * USB Port Configuration: |
| * [0] = enable |
| * [1] = overcurrent pin |
| * [2] = length |
| * |
| * Ports 0-7 can be mapped to OC0-OC3 |
| * Ports 8-13 can be mapped to OC4-OC7 |
| * |
| * Port Length |
| * MOBILE: |
| * < 0x050 = Setting 1 (back panel, 1 to 5 in, lowest tx amplitude) |
| * < 0x140 = Setting 2 (back panel, 5 to 14 in, highest tx amplitude) |
| * DESKTOP: |
| * < 0x080 = Setting 1 (front/back panel, less than 8 in, lowest tx amplitude) |
| * < 0x130 = Setting 2 (back panel, 8 to 13 in, higher tx amplitude) |
| * < 0x150 = Setting 3 (back panel, 13 to 15 in, highest tx amplitude) |
| */ |
| uint16_t usb_port_config[16][3]; |
| /* See the usb3 struct above for details */ |
| pch_usb3_controller_settings usb3; |
| /* |
| * SPD data array for onboard RAM. Note that spd_data [1..3] are ignored: instead, |
| * the "dimm_channel{0,1}_disabled" flag and the spd_addresses are used to determine |
| * which DIMMs should use the SPD from spd_data[0]. |
| */ |
| uint8_t spd_data[4][256]; |
| /* 32 bit pointer to tx_byte_func */ |
| uint32_t tx_byte_ptr; |
| |
| int ddr3lv_support; |
| /* |
| * pcie_init needs to be set to 1 to have the system agent initialize PCIe. |
| * Note: This should only be required if your system has Gen3 devices and |
| * it will increase your boot time by at least 100ms. |
| */ |
| int pcie_init; |
| /* |
| * N mode functionality. Leave this setting at 0. |
| * |
| * 0: Auto |
| * 1: 1N |
| * 2: 2N |
| */ |
| int nmode; |
| /* |
| * DDR refresh rate config. JEDEC Standard No.21-C Annex K allows for DIMM SPD data to |
| * specify whether double-rate is required for extended operating temperature range. |
| * |
| * 0: Enable double rate based upon temperature thresholds |
| * 1: Normal rate |
| * 2: Always enable double rate |
| */ |
| int ddr_refresh_rate_config; |
| } __packed; |
| |
| void southbridge_fill_pei_data(struct pei_data *pei_data); |
| #endif |