| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <bootblock_common.h> |
| #include <device/pnp_type.h> |
| #include <southbridge/intel/bd82x6x/pch.h> |
| |
| #include <superio/nuvoton/common/nuvoton.h> |
| #include <superio/nuvoton/nct6779d/nct6779d.h> |
| |
| #include <option.h> |
| |
| #include <northbridge/intel/sandybridge/raminit.h> |
| #include <northbridge/intel/sandybridge/pei_data.h> |
| |
| #define SERIAL_DEV PNP_DEV(0x2e, NCT6779D_SP2) |
| |
| const struct southbridge_usb_port mainboard_usb_ports[] = { |
| /* {enable, current, oc_pin} */ |
| { 1, 2, 0 }, /* Port 0: USB3 front internal header, top */ |
| { 1, 2, 0 }, /* Port 1: USB3 front internal header, bottom */ |
| { 1, 2, 1 }, /* Port 2: USB3 rear, ETH top */ |
| { 1, 2, 1 }, /* Port 3: USB3 rear, ETH bottom */ |
| { 1, 2, 2 }, /* Port 4: USB2 rear, PS2 top */ |
| { 1, 2, 2 }, /* Port 5: USB2 rear, PS2 bottom */ |
| { 1, 2, 3 }, /* Port 6: USB2 internal header USB78, top */ |
| { 1, 2, 3 }, /* Port 7: USB2 internal header USB78, bottom */ |
| { 1, 2, 4 }, /* Port 8: USB2 internal header USB910, top */ |
| { 1, 2, 4 }, /* Port 9: USB2 internal header USB910, bottom */ |
| { 1, 2, 6 }, /* Port 10: USB2 internal header USB1112, top */ |
| { 1, 2, 5 }, /* Port 11: USB2 internal header USB1112, bottom */ |
| { 0, 2, 5 }, /* Port 12: Unused. Asus proprietary DEBUG_PORT ??? */ |
| { 0, 2, 6 } /* Port 13: Unused. Asus proprietary DEBUG_PORT ??? */ |
| }; |
| |
| void bootblock_mainboard_early_init(void) |
| { |
| nuvoton_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); |
| } |
| |
| void mainboard_fill_pei_data(struct pei_data *pei_data) |
| { |
| /* |
| * USB3 mode: |
| * 0 = Disable: work always as USB 2.0(ehci) |
| * 1 = Enable: work always as USB 3.0(xhci) |
| * 2 = Auto: work as USB2.0(ehci) until OS loads USB3 xhci driver |
| * 3 = Smart Auto : same than Auto, but if OS loads USB3 driver |
| * and reboots, it will keep the USB3.0 speed |
| */ |
| pei_data->usb3.mode = get_uint_option("usb3_mode", 1) & 0x3; |
| /* Load USB3 pre-OS xHCI driver */ |
| pei_data->usb3.preboot_support = get_uint_option("usb3_drv", 1) & 0x1; |
| /* Use USB3 xHCI streams */ |
| pei_data->usb3.xhci_streams = get_uint_option("usb3_streams", 1) & 0x1; |
| } |