| uses HAVE_MP_TABLE |
| uses HAVE_PIRQ_TABLE |
| uses USE_FALLBACK_IMAGE |
| uses HAVE_FALLBACK_BOOT |
| uses HAVE_HARD_RESET |
| uses HAVE_OPTION_TABLE |
| uses USE_OPTION_TABLE |
| uses CONFIG_ROM_STREAM |
| uses IRQ_SLOT_COUNT |
| uses MAINBOARD |
| uses MAINBOARD_VENDOR |
| uses MAINBOARD_PART_NUMBER |
| uses LINUXBIOS_EXTRA_VERSION |
| uses ARCH |
| uses FALLBACK_SIZE |
| uses STACK_SIZE |
| uses HEAP_SIZE |
| uses ROM_SIZE |
| uses ROM_SECTION_SIZE |
| uses ROM_IMAGE_SIZE |
| uses ROM_SECTION_SIZE |
| uses ROM_SECTION_OFFSET |
| uses CONFIG_ROM_STREAM_START |
| uses CONFIG_COMPRESSED_ROM_STREAM |
| uses CONFIG_PRECOMPRESSED_ROM_STREAM |
| uses PAYLOAD_SIZE |
| uses _ROMBASE |
| uses _RAMBASE |
| uses XIP_ROM_SIZE |
| uses XIP_ROM_BASE |
| uses HAVE_MP_TABLE |
| uses CROSS_COMPILE |
| uses CC |
| uses HOSTCC |
| uses OBJCOPY |
| uses DEFAULT_CONSOLE_LOGLEVEL |
| uses MAXIMUM_CONSOLE_LOGLEVEL |
| uses CONFIG_CONSOLE_SERIAL8250 |
| uses TTYS0_BAUD |
| uses TTYS0_BASE |
| uses TTYS0_LCS |
| uses CONFIG_UDELAY_TSC |
| uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 |
| |
| ## ROM_SIZE is the size of boot ROM that this board will use. |
| default ROM_SIZE = 256*1024 |
| |
| ### |
| ### Build options |
| ### |
| |
| ## |
| ## Build code for the fallback boot |
| ## |
| default HAVE_FALLBACK_BOOT=1 |
| |
| ## |
| ## no MP table |
| ## |
| default HAVE_MP_TABLE=0 |
| |
| ## |
| ## Build code to reset the motherboard from linuxBIOS |
| ## |
| default HAVE_HARD_RESET=0 |
| |
| ## Delay timer options |
| ## |
| default CONFIG_UDELAY_TSC=1 |
| default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 |
| |
| ## |
| ## Build code to export a programmable irq routing table |
| ## |
| default HAVE_PIRQ_TABLE=1 |
| default IRQ_SLOT_COUNT=2 |
| #object irq_tables.o |
| |
| ## |
| ## Build code to export a CMOS option table |
| ## |
| default HAVE_OPTION_TABLE=0 |
| |
| ### |
| ### LinuxBIOS layout values |
| ### |
| |
| ## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. |
| default ROM_IMAGE_SIZE = 65536 |
| default FALLBACK_SIZE = 131072 |
| |
| ## |
| ## Use a small 8K stack |
| ## |
| default STACK_SIZE=0x2000 |
| |
| ## |
| ## Use a small 16K heap |
| ## |
| default HEAP_SIZE=0x4000 |
| |
| ## |
| ## Only use the option table in a normal image |
| ## |
| #default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE |
| default USE_OPTION_TABLE = 0 |
| |
| default _RAMBASE = 0x00004000 |
| |
| default CONFIG_ROM_STREAM = 1 |
| |
| ## |
| ## The default compiler |
| ## |
| default CROSS_COMPILE="" |
| default CC="$(CROSS_COMPILE)gcc -m32" |
| default HOSTCC="gcc" |
| |
| ## |
| ## The Serial Console |
| ## |
| |
| # To Enable the Serial Console |
| default CONFIG_CONSOLE_SERIAL8250=1 |
| |
| ## Select the serial console baud rate |
| default TTYS0_BAUD=115200 |
| #default TTYS0_BAUD=57600 |
| #default TTYS0_BAUD=38400 |
| #default TTYS0_BAUD=19200 |
| #default TTYS0_BAUD=9600 |
| #default TTYS0_BAUD=4800 |
| #default TTYS0_BAUD=2400 |
| #default TTYS0_BAUD=1200 |
| |
| # Select the serial console base port |
| default TTYS0_BASE=0x3f8 |
| |
| # Select the serial protocol |
| # This defaults to 8 data bits, 1 stop bit, and no parity |
| default TTYS0_LCS=0x3 |
| |
| ## |
| ### Select the linuxBIOS loglevel |
| ## |
| ## EMERG 1 system is unusable |
| ## ALERT 2 action must be taken immediately |
| ## CRIT 3 critical conditions |
| ## ERR 4 error conditions |
| ## WARNING 5 warning conditions |
| ## NOTICE 6 normal but significant condition |
| ## INFO 7 informational |
| ## DEBUG 8 debug-level messages |
| ## SPEW 9 Way too many details |
| |
| ## Request this level of debugging output |
| default DEFAULT_CONSOLE_LOGLEVEL=8 |
| ## At a maximum only compile in this level of debugging |
| default MAXIMUM_CONSOLE_LOGLEVEL=8 |
| |
| end |
| |