| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <acpi/acpi_device.h> |
| #include <acpi/acpigen.h> |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pci_ids.h> |
| #include <device/pci_ops.h> |
| #include "chip.h" |
| #include <soc/acp.h> |
| #include <soc/acpi.h> |
| #include <soc/pci_devs.h> |
| #include <soc/southbridge.h> |
| #include <amdblocks/acpimmio.h> |
| #include <commonlib/helpers.h> |
| |
| static void init(struct device *dev) |
| { |
| const struct soc_amd_picasso_config *cfg; |
| struct resource *res; |
| uintptr_t bar; |
| |
| /* Set the proper I2S_PIN_CONFIG state */ |
| cfg = config_of_soc(); |
| |
| res = dev->resource_list; |
| if (!res || !res->base) { |
| printk(BIOS_ERR, "Error, unable to configure pin in %s\n", __func__); |
| return; |
| } |
| |
| bar = (uintptr_t)res->base; |
| write32((void *)(bar + ACP_I2S_PIN_CONFIG), cfg->acp_pin_cfg); |
| |
| if (cfg->acp_pin_cfg == I2S_PINS_I2S_TDM) |
| sb_clk_output_48Mhz(); /* Internal connection to I2S */ |
| } |
| |
| static const char *acp_acpi_name(const struct device *dev) |
| { |
| return "ACPD"; |
| } |
| |
| #define AMD_I2S_ACPI_NAME "I2SM" |
| #define AMD_I2S_ACPI_HID "AMDI5682" |
| #define AMD_I2S_ACPI_DESC "I2S machine driver" |
| |
| static void acp_fill_i2s_machine_dev(const struct device *dev) |
| { |
| const char *scope = acpi_device_path(dev); |
| const struct soc_amd_picasso_config *cfg = config_of_soc(); |
| const struct acpi_gpio *dmic_select_gpio = &cfg->dmic_select_gpio; |
| struct acpi_dp *dsd; |
| |
| if (dmic_select_gpio->pin_count == 0) |
| return; |
| |
| acpigen_write_scope(scope); /* Scope */ |
| acpigen_write_device(AMD_I2S_ACPI_NAME); /* Device */ |
| acpigen_write_name_string("_HID", AMD_I2S_ACPI_HID); |
| acpigen_write_name_integer("_UID", 1); |
| acpigen_write_name_string("_DDN", AMD_I2S_ACPI_DESC); |
| |
| acpigen_write_STA(ACPI_STATUS_DEVICE_ALL_ON); |
| |
| /* Resources */ |
| acpigen_write_name("_CRS"); |
| acpigen_write_resourcetemplate_header(); |
| acpi_device_write_gpio(dmic_select_gpio); |
| acpigen_write_resourcetemplate_footer(); |
| |
| dsd = acpi_dp_new_table("_DSD"); |
| /* |
| * This GPIO is used to select DMIC0 or DMIC1 by the kernel driver. It does not |
| * really have a polarity since low and high control the selection of DMIC and |
| * hence does not have an active polarity. |
| * Kernel driver does not use the polarity field and instead treats the GPIO |
| * selection as follows: |
| * Set low (0) = Select DMIC0 |
| * Set high (1) = Select DMIC1 |
| */ |
| acpi_dp_add_gpio(dsd, "dmic-gpios", acpi_device_path_join(dev, AMD_I2S_ACPI_NAME), |
| 0, /* Index = 0 (There is a single GPIO entry in _CRS). */ |
| 0, /* Pin = 0 (There is a single pin in the GPIO resource). */ |
| 0); /* Active low = 0 (Kernel driver does not use active polarity). */ |
| acpi_dp_write(dsd); |
| |
| acpigen_pop_len(); /* Device */ |
| acpigen_pop_len(); /* Scope */ |
| } |
| |
| static void acp_fill_ssdt(const struct device *dev) |
| { |
| acpi_device_write_pci_dev(dev); |
| acp_fill_i2s_machine_dev(dev); |
| } |
| |
| static struct device_operations acp_ops = { |
| .read_resources = pci_dev_read_resources, |
| .set_resources = pci_dev_set_resources, |
| .enable_resources = pci_dev_enable_resources, |
| .init = init, |
| .ops_pci = &pci_dev_ops_pci, |
| .acpi_name = acp_acpi_name, |
| .acpi_fill_ssdt = acp_fill_ssdt, |
| }; |
| |
| static const struct pci_driver acp_driver __pci_driver = { |
| .ops = &acp_ops, |
| .vendor = PCI_VENDOR_ID_AMD, |
| .device = PCI_DEVICE_ID_AMD_FAM17H_ACP, |
| }; |