| # SPDX-License-Identifier: GPL-2.0-only |
| |
| config IDS_OPTIONS_HOOKED_UP |
| bool |
| help |
| to Kconfig options. |
| Historically, IDS configuration was defined in a mainboard-specific |
| `OptionsIds.h` header. Select this on platforms where IDS config is |
| hooked up to Kconfig options instead. |
| |
| if IDS_OPTIONS_HOOKED_UP |
| |
| config IDS_ENABLED |
| bool "Enable AGESA IDS (Integrated Debug Services) support" |
| default y |
| help |
| This is the master switch for the IDS sub-system. Use this option to |
| enable or remove the entire IDS feature set. This switch must be TRUE |
| for any of the other options to function. |
| |
| comment "Warning: IDS options may not work. Enable at your own risk!" |
| depends on IDS_ENABLED |
| |
| config IDS_CONTROL_ENABLED |
| bool "Enable IDS User Interface controls" |
| depends on IDS_ENABLED |
| help |
| This is the main switch for the IDS configuration controls. This |
| switch must be TRUE for any of the configuration controls to function. |
| |
| This seems to allow AGESA to retrieve settings from CMOS. |
| |
| config IDS_PERF_ANALYSIS |
| bool "Enable IDS performance analysis" |
| depends on IDS_ENABLED |
| help |
| This is the main switch for the IDS performance analysis controls, |
| macros and support code needed to enable time data gathering. This |
| switch must be TRUE for any of the performance analysis features to |
| function. |
| |
| config IDS_TRACING_ENABLED |
| bool "Enable IDS console" |
| depends on IDS_ENABLED |
| help |
| This is the main switch for the IDS console controls, macros and |
| support code needed to enable tracing of algorithms. This switch |
| must be TRUE for any of the tracing features to function. |
| |
| config IDS_TRACING_CONSOLE_SERIAL |
| bool "Use serial port as IDS console" |
| depends on IDS_TRACING_ENABLED |
| default DRIVERS_UART_8250IO && CONSOLE_SERIAL |
| help |
| Use an I/O-mapped serial port to output IDS messages. |
| |
| endif # IDS_OPTIONS_HOOKED_UP |
| |
| choice |
| prompt "DDR3 memory profile" |
| default CPU_AMD_AGESA_OPENSOURCE_MEM_JEDEC |
| help |
| Choose the DDR3 memory profile to use for your RAM sticks, e.g. XMP 1. |
| XMP support is experimental, and your PC will fail booting if you choose |
| a profile which does not exist on ANY of your RAM sticks! If in doubt |
| check their SPD Data using a coreboot's great fork of memtest86+ 5.01. |
| |
| config CPU_AMD_AGESA_OPENSOURCE_MEM_JEDEC |
| bool "JEDEC" |
| help |
| JEDEC memory profile, standard and stable. Is guaranteed to be working. |
| |
| config CPU_AMD_AGESA_OPENSOURCE_MEM_XMP_1 |
| bool "XMP 1" |
| help |
| XMP 1 memory profile. Check that it exists on ALL of your RAM sticks! |
| |
| config CPU_AMD_AGESA_OPENSOURCE_MEM_XMP_2 |
| bool "XMP 2" |
| help |
| XMP 2 memory profile. Check that it exists on ALL of your RAM sticks! |
| |
| config CPU_AMD_AGESA_OPENSOURCE_MEM_CUSTOM |
| bool "CUSTOM" |
| help |
| Custom memory profile. Use the XMP SPD values as the base, if available. |
| |
| endchoice |
| |
| if CPU_AMD_AGESA_OPENSOURCE_MEM_CUSTOM |
| |
| config CUSTOM_SPD_DIVIDENT |
| int "[10]: Medium Timebase (MTB) Dividend" |
| default 1 |
| range 1 255 |
| |
| config CUSTOM_SPD_DIVISOR |
| int "[11]: Medium Timebase (MTB) Divisor" |
| default 14 |
| range 1 255 |
| |
| config CUSTOM_SPD_TCK |
| int "[12]: SDRAM Minimum Cycle Time, tCK" |
| default 15 |
| range 1 255 |
| |
| config CUSTOM_SPD_CASLO |
| int "[14]: CAS Latencies Supported, Lower Byte" |
| default 124 |
| range 0 255 |
| |
| config CUSTOM_SPD_CASHI |
| int "[15]: CAS Latencies Supported, Higher Byte" |
| default 0 |
| range 0 255 |
| |
| config CUSTOM_SPD_TAA |
| int "[16]: Min CAS Latency Time, tAA" |
| default 132 |
| range 1 255 |
| |
| config CUSTOM_SPD_TWR |
| int "[17]: Min Write Recovery Time, tWR" |
| default 210 |
| range 1 255 |
| |
| config CUSTOM_SPD_TRCD |
| int "[18]: Min RAS# to CAS# Delay Time, tRCD" |
| default 132 |
| range 1 255 |
| |
| config CUSTOM_SPD_TRRD |
| int "[19]: Min Row Active to Row Active Delay Time, tRRD" |
| default 84 |
| range 1 255 |
| |
| config CUSTOM_SPD_TRP |
| int "[20]: Min Row Precharge Delay Time, tRP" |
| default 132 |
| range 1 255 |
| |
| config CUSTOM_SPD_UPPER_TRC |
| int "[21][7:4]: Min Active to Active/Refresh Delay, UPPER tRC" |
| default 2 |
| range 0 16 |
| |
| config CUSTOM_SPD_UPPER_TRAS |
| int "[21][3:0]: Min Active to Precharge Delay Time, UPPER tRAS" |
| default 1 |
| range 0 16 |
| |
| config CUSTOM_SPD_TRAS |
| int "[22]: Min Active to Precharge Delay Time, LOWER tRAS" |
| default 138 |
| range 1 255 |
| |
| config CUSTOM_SPD_TRC |
| int "[23]: Min Active to Active/Refresh Delay, LOWER tRC" |
| default 181 |
| range 1 255 |
| |
| config CUSTOM_SPD_TWTR |
| int "[26]: Min Internal Write to Read Command Delay, tWTR" |
| default 105 |
| range 1 255 |
| |
| config CUSTOM_SPD_TRTP |
| int "[27]: Min Internal Read to Precharge Command Delay, tRTP" |
| default 105 |
| range 1 255 |
| |
| config CUSTOM_SPD_UPPER_TFAW |
| int "[28][3:0]: Min Four Activate Window Delay, UPPER tFAW" |
| default 1 |
| range 0 16 |
| |
| config CUSTOM_SPD_TFAW |
| int "[29]: Min Four Activate Window Delay Time, tFAW" |
| default 164 |
| range 1 255 |
| |
| endif |