| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2010 Advanced Micro Devices, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| //#define SYSTEM_TYPE 0 /* SERVER */ |
| #define SYSTEM_TYPE 1 /* DESKTOP */ |
| //#define SYSTEM_TYPE 2 /* MOBILE */ |
| |
| //used by incoherent_ht |
| #define FAM10_SCAN_PCI_BUS 0 |
| #define FAM10_ALLOCATE_IO_RANGE 0 |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <device/pci_def.h> |
| #include <device/pci_ids.h> |
| #include <arch/io.h> |
| #include <device/pnp_def.h> |
| #include <arch/romcc_io.h> |
| #include <cpu/x86/lapic.h> |
| #include <console/console.h> |
| #include <cpu/amd/model_10xxx_rev.h> |
| #include "northbridge/amd/amdfam10/raminit.h" |
| #include "northbridge/amd/amdfam10/amdfam10.h" |
| #include <lib.h> |
| #include "cpu/x86/lapic/boot_cpu.c" |
| #include "northbridge/amd/amdfam10/reset_test.c" |
| #include <console/loglevel.h> |
| #include "cpu/x86/bist.h" |
| #include "superio/ite/it8718f/early_serial.c" |
| #include <usbdebug.h> |
| #include "cpu/x86/mtrr/earlymtrr.c" |
| #include <cpu/amd/mtrr.h> |
| #include "northbridge/amd/amdfam10/setup_resource_map.c" |
| #include "southbridge/amd/rs780/early_setup.c" |
| #include "southbridge/amd/sb700/sb700.h" |
| #include "southbridge/amd/sb700/smbus.h" |
| #include "northbridge/amd/amdfam10/debug.c" |
| |
| static void activate_spd_rom(const struct mem_controller *ctrl) { } |
| |
| static int spd_read_byte(u32 device, u32 address) |
| { |
| return do_smbus_read_byte(SMBUS_IO_BASE, device, address); |
| } |
| |
| #include "northbridge/amd/amdfam10/amdfam10.h" |
| #include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c" |
| #include "northbridge/amd/amdfam10/pci.c" |
| #include "resourcemap.c" |
| #include "cpu/amd/quadcore/quadcore.c" |
| #include "cpu/amd/car/post_cache_as_ram.c" |
| #include "cpu/amd/microcode/microcode.c" |
| |
| #if CONFIG_UPDATE_CPU_MICROCODE |
| #include "cpu/amd/model_10xxx/update_microcode.c" |
| #endif |
| |
| #include "cpu/amd/model_10xxx/init_cpus.c" |
| #include "northbridge/amd/amdfam10/early_ht.c" |
| #include <spd.h> |
| |
| void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) |
| { |
| struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); |
| static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, }; |
| u32 bsp_apicid = 0, val; |
| msr_t msr; |
| |
| if (!cpu_init_detectedx && boot_cpu()) { |
| /* Nothing special needs to be done to find bus 0 */ |
| /* Allow the HT devices to be found */ |
| /* mov bsp to bus 0xff when > 8 nodes */ |
| set_bsp_node_CHtExtNodeCfgEn(); |
| enumerate_ht_chain(); |
| sb7xx_51xx_pci_port80(); |
| } |
| |
| post_code(0x30); |
| |
| if (bist == 0) { |
| bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */ |
| /* All cores run this but the BSP(node0,core0) is the only core that returns. */ |
| } |
| |
| post_code(0x32); |
| |
| enable_rs780_dev8(); |
| sb7xx_51xx_lpc_init(); |
| |
| it8718f_enable_serial(0, CONFIG_TTYS0_BASE); |
| it8718f_disable_reboot(); |
| |
| console_init(); |
| |
| /* Halt if there was a built in self test failure */ |
| report_bist_failure(bist); |
| |
| // Load MPB |
| val = cpuid_eax(1); |
| printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val); |
| printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1); |
| printk(BIOS_DEBUG, "bsp_apicid = %02x \n", bsp_apicid); |
| printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx); |
| |
| /* Setup sysinfo defaults */ |
| set_sysinfo_in_ram(0); |
| |
| #if CONFIG_UPDATE_CPU_MICROCODE |
| update_microcode(val); |
| #endif |
| post_code(0x33); |
| |
| cpuSetAMDMSR(); |
| post_code(0x34); |
| |
| amd_ht_init(sysinfo); |
| post_code(0x35); |
| |
| /* Setup nodes PCI space and start core 0 AP init. */ |
| finalize_node_setup(sysinfo); |
| |
| /* Setup any mainboard PCI settings etc. */ |
| setup_mb_resource_map(); |
| post_code(0x36); |
| |
| /* wait for all the APs core0 started by finalize_node_setup. */ |
| /* FIXME: A bunch of cores are going to start output to serial at once. |
| It would be nice to fixup prink spinlocks for ROM XIP mode. |
| I think it could be done by putting the spinlock flag in the cache |
| of the BSP located right after sysinfo. |
| */ |
| wait_all_core0_started(); |
| |
| #if CONFIG_LOGICAL_CPUS==1 |
| /* Core0 on each node is configured. Now setup any additional cores. */ |
| printk(BIOS_DEBUG, "start_other_cores()\n"); |
| start_other_cores(); |
| post_code(0x37); |
| wait_all_other_cores_started(bsp_apicid); |
| #endif |
| |
| post_code(0x38); |
| |
| /* run _early_setup before soft-reset. */ |
| rs780_early_setup(); |
| sb7xx_51xx_early_setup(); |
| |
| #if CONFIG_SET_FIDVID |
| msr = rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo); |
| |
| /* FIXME: The sb fid change may survive the warm reset and only |
| need to be done once.*/ |
| enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); |
| |
| post_code(0x39); |
| |
| if (!warm_reset_detect(0)) { // BSP is node 0 |
| init_fidvid_bsp(bsp_apicid, sysinfo->nodes); |
| } else { |
| init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0 |
| } |
| |
| post_code(0x3A); |
| |
| /* show final fid and vid */ |
| msr=rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo); |
| #endif |
| |
| rs780_htinit(); |
| |
| /* Reset for HT, FIDVID, PLL and errata changes to take affect. */ |
| if (!warm_reset_detect(0)) { |
| print_info("...WARM RESET...\n\n\n"); |
| soft_reset(); |
| die("After soft_reset_x - shouldn't see this message!!!\n"); |
| } |
| |
| post_code(0x3B); |
| |
| /* It's the time to set ctrl in sysinfo now; */ |
| printk(BIOS_DEBUG, "fill_mem_ctrl()\n"); |
| fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); |
| |
| post_code(0x40); |
| |
| // die("Die Before MCT init."); |
| |
| printk(BIOS_DEBUG, "raminit_amdmct()\n"); |
| raminit_amdmct(sysinfo); |
| post_code(0x41); |
| |
| /* |
| dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200); |
| dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200); |
| dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200); |
| dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200); |
| */ |
| |
| // die("After MCT init before CAR disabled."); |
| |
| rs780_before_pci_init(); |
| sb7xx_51xx_before_pci_init(); |
| |
| post_code(0x42); |
| printk(BIOS_DEBUG, "\n*** Yes, the copy/decompress is taking a while, FIXME!\n"); |
| post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB. |
| post_code(0x43); // Should never see this post code. |
| } |
| |
| /** |
| * BOOL AMD_CB_ManualBUIDSwapList(u8 Node, u8 Link, u8 **List) |
| * Description: |
| * This routine is called every time a non-coherent chain is processed. |
| * BUID assignment may be controlled explicitly on a non-coherent chain. Provide a |
| * swap list. The first part of the list controls the BUID assignment and the |
| * second part of the list provides the device to device linking. Device orientation |
| * can be detected automatically, or explicitly. See documentation for more details. |
| * |
| * Automatic non-coherent init assigns BUIDs starting at 1 and incrementing sequentially |
| * based on each device's unit count. |
| * |
| * Parameters: |
| * @param[in] u8 node = The node on which this chain is located |
| * @param[in] u8 link = The link on the host for this chain |
| * @param[out] u8** list = supply a pointer to a list |
| * @param[out] BOOL result = true to use a manual list |
| * false to initialize the link automatically |
| */ |
| BOOL AMD_CB_ManualBUIDSwapList (u8 node, u8 link, const u8 **List) |
| { |
| static const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF }; |
| /* If the BUID was adjusted in early_ht we need to do the manual override */ |
| if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) { |
| printk(BIOS_DEBUG, "AMD_CB_ManualBUIDSwapList()\n"); |
| if ((node == 0) && (link == 0)) { /* BSP SB link */ |
| *List = swaplist; |
| return 1; |
| } |
| } |
| |
| return 0; |
| } |