| // 16bit code to access floppy drives. |
| // |
| // Copyright (C) 2008 Kevin O'Connor <kevin@koconnor.net> |
| // Copyright (C) 2002 MandrakeSoft S.A. |
| // |
| // This file may be distributed under the terms of the GNU GPLv3 license. |
| |
| #include "types.h" // u8 |
| #include "disk.h" // DISK_RET_SUCCESS |
| #include "config.h" // CONFIG_FLOPPY_SUPPORT |
| #include "biosvar.h" // SET_BDA |
| #include "util.h" // irq_disable |
| #include "cmos.h" // inb_cmos |
| #include "pic.h" // unmask_pic1 |
| #include "bregs.h" // struct bregs |
| |
| #define BX_FLOPPY_ON_CNT 37 /* 2 seconds */ |
| |
| // New diskette parameter table adding 3 parameters from IBM |
| // Since no provisions are made for multiple drive types, most |
| // values in this table are ignored. I set parameters for 1.44M |
| // floppy here |
| #if MODE16 == 1 |
| struct floppy_ext_dbt_s diskette_param_table2 VISIBLE16 = { |
| .dbt = { |
| .specify1 = 0xAF, |
| .specify2 = 0x02, // head load time 0000001, DMA used |
| .shutoff_ticks = 0x25, |
| .bps_code = 0x02, |
| .sectors = 18, |
| .interblock_len = 0x1B, |
| .data_len = 0xFF, |
| .gap_len = 0x6C, |
| .fill_byte = 0xF6, |
| .settle_time = 0x0F, |
| .startup_time = 0x08, |
| }, |
| .max_track = 79, // maximum track |
| .data_rate = 0, // data transfer rate |
| .drive_type = 4, // drive type in cmos |
| }; |
| #endif |
| |
| void |
| floppy_drive_setup() |
| { |
| if (! CONFIG_FLOPPY_SUPPORT) |
| return; |
| dprintf(3, "init floppy drives\n"); |
| if (CONFIG_COREBOOT) |
| // XXX - disable floppies on coreboot for now. |
| outb_cmos(0, CMOS_FLOPPY_DRIVE_TYPE); |
| u8 type = inb_cmos(CMOS_FLOPPY_DRIVE_TYPE); |
| u8 out = 0; |
| u8 num_floppies = 0; |
| |
| if (type & 0xf0) { |
| out |= 0x07; |
| num_floppies++; |
| } |
| if (type & 0x0f) { |
| out |= 0x70; |
| num_floppies++; |
| } |
| SET_BDA(floppy_harddisk_info, out); |
| |
| // Update equipment word bits for floppy |
| if (num_floppies == 1) |
| // 1 drive, ready for boot |
| SETBITS_BDA(equipment_list_flags, 0x01); |
| else if (num_floppies == 2) |
| // 2 drives, ready for boot |
| SETBITS_BDA(equipment_list_flags, 0x41); |
| |
| outb(0x02, PORT_DMA1_MASK_REG); |
| |
| // Enable IRQ6 (handle_0e) |
| unmask_pic1(PIC1_IRQ6); |
| } |
| |
| static inline void |
| set_diskette_current_cyl(u8 drive, u8 cyl) |
| { |
| if (drive) |
| SET_BDA(floppy_track1, cyl); |
| else |
| SET_BDA(floppy_track0, cyl); |
| } |
| |
| static u16 |
| get_drive_type(u8 drive) |
| { |
| // check CMOS to see if drive exists |
| u8 drive_type = inb_cmos(CMOS_FLOPPY_DRIVE_TYPE); |
| if (drive == 0) |
| drive_type >>= 4; |
| else |
| drive_type &= 0x0f; |
| return drive_type; |
| } |
| |
| static u16 |
| floppy_media_known(u8 drive) |
| { |
| if (!(GET_BDA(floppy_recalibration_status) & (1<<drive))) |
| return 0; |
| u8 v = GET_BDA(floppy_media_state[drive]); |
| if (!(v & FMS_MEDIA_DRIVE_ESTABLISHED)) |
| return 0; |
| return 1; |
| } |
| |
| static void |
| floppy_reset_controller() |
| { |
| // Reset controller |
| u8 val8 = inb(PORT_FD_DOR); |
| outb(val8 & ~0x04, PORT_FD_DOR); |
| outb(val8 | 0x04, PORT_FD_DOR); |
| |
| // Wait for controller to come out of reset |
| while ((inb(PORT_FD_STATUS) & 0xc0) != 0x80) |
| ; |
| } |
| |
| static void |
| floppy_prepare_controller(u8 drive) |
| { |
| CLEARBITS_BDA(floppy_recalibration_status, FRS_TIMEOUT); |
| |
| // turn on motor of selected drive, DMA & int enabled, normal operation |
| u8 prev_reset = inb(PORT_FD_DOR) & 0x04; |
| u8 dor = 0x10; |
| if (drive) |
| dor = 0x20; |
| dor |= 0x0c; |
| dor |= drive; |
| outb(dor, PORT_FD_DOR); |
| |
| // reset the disk motor timeout value of INT 08 |
| SET_BDA(floppy_motor_counter, BX_FLOPPY_ON_CNT); |
| |
| // wait for drive readiness |
| while ((inb(PORT_FD_STATUS) & 0xc0) != 0x80) |
| ; |
| |
| if (prev_reset == 0) { |
| irq_enable(); |
| u8 v; |
| for (;;) { |
| v = GET_BDA(floppy_recalibration_status); |
| if (v & FRS_TIMEOUT) |
| break; |
| cpu_relax(); |
| } |
| irq_disable(); |
| |
| v &= ~FRS_TIMEOUT; |
| SET_BDA(floppy_recalibration_status, v); |
| } |
| } |
| |
| static int |
| floppy_pio(u8 *cmd, u8 cmdlen) |
| { |
| floppy_prepare_controller(cmd[1] & 1); |
| |
| // send command to controller |
| u8 i; |
| for (i=0; i<cmdlen; i++) |
| outb(cmd[i], PORT_FD_DATA); |
| |
| irq_enable(); |
| u8 v; |
| for (;;) { |
| if (!GET_BDA(floppy_motor_counter)) { |
| irq_disable(); |
| floppy_reset_controller(); |
| return -1; |
| } |
| v = GET_BDA(floppy_recalibration_status); |
| if (v & FRS_TIMEOUT) |
| break; |
| cpu_relax(); |
| } |
| irq_disable(); |
| |
| v &= ~FRS_TIMEOUT; |
| SET_BDA(floppy_recalibration_status, v); |
| |
| return 0; |
| } |
| |
| #define floppy_ret(regs, code) \ |
| __floppy_ret(__func__, __LINE__, (regs), (code)) |
| |
| void |
| __floppy_ret(const char *fname, int lineno, struct bregs *regs, u8 code) |
| { |
| SET_BDA(floppy_last_status, code); |
| if (code) |
| __set_code_fail(fname, lineno, regs, code); |
| else |
| set_code_success(regs); |
| } |
| |
| static int |
| floppy_cmd(struct bregs *regs, u16 count, u8 *cmd, u8 cmdlen) |
| { |
| // es:bx = pointer to where to place information from diskette |
| u32 addr = (u32)MAKE_FARPTR(regs->es, regs->bx); |
| |
| // check for 64K boundary overrun |
| u32 last_addr = addr + count; |
| if ((addr >> 16) != (last_addr >> 16)) { |
| floppy_ret(regs, DISK_RET_EBOUNDARY); |
| return -1; |
| } |
| |
| u8 mode_register = 0x4a; // single mode, increment, autoinit disable, |
| if (cmd[0] == 0xe6) |
| // read |
| mode_register = 0x46; |
| |
| //DEBUGF("floppy dma c2\n"); |
| outb(0x06, PORT_DMA1_MASK_REG); |
| outb(0x00, PORT_DMA1_CLEAR_FF_REG); // clear flip-flop |
| outb(addr, PORT_DMA_ADDR_2); |
| outb(addr>>8, PORT_DMA_ADDR_2); |
| outb(0x00, PORT_DMA1_CLEAR_FF_REG); // clear flip-flop |
| outb(count, PORT_DMA_CNT_2); |
| outb(count>>8, PORT_DMA_CNT_2); |
| |
| // port 0b: DMA-1 Mode Register |
| // transfer type=write, channel 2 |
| outb(mode_register, PORT_DMA1_MODE_REG); |
| |
| // port 81: DMA-1 Page Register, channel 2 |
| outb(addr>>16, PORT_DMA_PAGE_2); |
| |
| outb(0x02, PORT_DMA1_MASK_REG); // unmask channel 2 |
| |
| int ret = floppy_pio(cmd, cmdlen); |
| if (ret) { |
| floppy_ret(regs, DISK_RET_ETIMEOUT); |
| return -1; |
| } |
| |
| // check port 3f4 for accessibility to status bytes |
| if ((inb(PORT_FD_STATUS) & 0xc0) != 0xc0) |
| BX_PANIC("int13_diskette: ctrl not ready\n"); |
| |
| // read 7 return status bytes from controller |
| u8 i; |
| for (i=0; i<7; i++) { |
| u8 v = inb(PORT_FD_DATA); |
| cmd[i] = v; |
| SET_BDA(floppy_return_status[i], v); |
| } |
| |
| return 0; |
| } |
| |
| static void |
| floppy_drive_recal(u8 drive) |
| { |
| // send Recalibrate command (2 bytes) to controller |
| u8 data[12]; |
| data[0] = 0x07; // 07: Recalibrate |
| data[1] = drive; // 0=drive0, 1=drive1 |
| floppy_pio(data, 2); |
| |
| SETBITS_BDA(floppy_recalibration_status, 1<<drive); |
| set_diskette_current_cyl(drive, 0); |
| } |
| |
| static u16 |
| floppy_media_sense(u8 drive) |
| { |
| u16 rv; |
| u8 config_data, media_state; |
| |
| floppy_drive_recal(drive); |
| |
| // for now cheat and get drive type from CMOS, |
| // assume media is same as drive type |
| |
| // ** config_data ** |
| // Bitfields for diskette media control: |
| // Bit(s) Description (Table M0028) |
| // 7-6 last data rate set by controller |
| // 00=500kbps, 01=300kbps, 10=250kbps, 11=1Mbps |
| // 5-4 last diskette drive step rate selected |
| // 00=0Ch, 01=0Dh, 10=0Eh, 11=0Ah |
| // 3-2 {data rate at start of operation} |
| // 1-0 reserved |
| |
| // ** media_state ** |
| // Bitfields for diskette drive media state: |
| // Bit(s) Description (Table M0030) |
| // 7-6 data rate |
| // 00=500kbps, 01=300kbps, 10=250kbps, 11=1Mbps |
| // 5 double stepping required (e.g. 360kB in 1.2MB) |
| // 4 media type established |
| // 3 drive capable of supporting 4MB media |
| // 2-0 on exit from BIOS, contains |
| // 000 trying 360kB in 360kB |
| // 001 trying 360kB in 1.2MB |
| // 010 trying 1.2MB in 1.2MB |
| // 011 360kB in 360kB established |
| // 100 360kB in 1.2MB established |
| // 101 1.2MB in 1.2MB established |
| // 110 reserved |
| // 111 all other formats/drives |
| |
| switch (get_drive_type(drive)) { |
| case 1: |
| // 360K 5.25" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x25; // 0010 0101 |
| rv = 1; |
| break; |
| case 2: |
| // 1.2 MB 5.25" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x25; // 0010 0101 // need double stepping??? (bit 5) |
| rv = 1; |
| break; |
| case 3: |
| // 720K 3.5" drive |
| config_data = 0x00; // 0000 0000 ??? |
| media_state = 0x17; // 0001 0111 |
| rv = 1; |
| break; |
| case 4: |
| // 1.44 MB 3.5" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x17; // 0001 0111 |
| rv = 1; |
| break; |
| case 5: |
| // 2.88 MB 3.5" drive |
| config_data = 0xCC; // 1100 1100 |
| media_state = 0xD7; // 1101 0111 |
| rv = 1; |
| break; |
| // |
| // Extended floppy size uses special cmos setting |
| case 6: |
| // 160k 5.25" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x27; // 0010 0111 |
| rv = 1; |
| break; |
| case 7: |
| // 180k 5.25" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x27; // 0010 0111 |
| rv = 1; |
| break; |
| case 8: |
| // 320k 5.25" drive |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x27; // 0010 0111 |
| rv = 1; |
| break; |
| default: |
| // not recognized |
| config_data = 0x00; // 0000 0000 |
| media_state = 0x00; // 0000 0000 |
| rv = 0; |
| } |
| |
| SET_BDA(floppy_last_data_rate, config_data); |
| SET_BDA(floppy_media_state[drive], media_state); |
| return rv; |
| } |
| |
| static int |
| check_drive(struct bregs *regs, u8 drive) |
| { |
| // see if drive exists |
| if (drive > 1 || !get_drive_type(drive)) { |
| // XXX - return type doesn't match |
| floppy_ret(regs, DISK_RET_ETIMEOUT); |
| return -1; |
| } |
| |
| // see if media in drive, and type is known |
| if (floppy_media_known(drive) == 0 && floppy_media_sense(drive) == 0) { |
| floppy_ret(regs, DISK_RET_EMEDIA); |
| return -1; |
| } |
| return 0; |
| } |
| |
| // diskette controller reset |
| static void |
| floppy_1300(struct bregs *regs, u8 drive) |
| { |
| if (drive > 1) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| return; |
| } |
| if (!get_drive_type(drive)) { |
| floppy_ret(regs, DISK_RET_ETIMEOUT); |
| return; |
| } |
| set_diskette_current_cyl(drive, 0); // current cylinder |
| floppy_ret(regs, DISK_RET_SUCCESS); |
| } |
| |
| // Read Diskette Status |
| static void |
| floppy_1301(struct bregs *regs, u8 drive) |
| { |
| u8 v = GET_BDA(floppy_last_status); |
| regs->ah = v; |
| set_cf(regs, v); |
| } |
| |
| // Read Diskette Sectors |
| static void |
| floppy_1302(struct bregs *regs, u8 drive) |
| { |
| if (check_drive(regs, drive)) |
| goto fail; |
| |
| u8 num_sectors = regs->al; |
| u8 track = regs->ch; |
| u8 sector = regs->cl; |
| u8 head = regs->dh; |
| |
| if (head > 1 || sector == 0 || num_sectors == 0 |
| || track > 79 || num_sectors > 72) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| goto fail; |
| } |
| |
| // send read-normal-data command (9 bytes) to controller |
| u8 data[12]; |
| data[0] = 0xe6; // e6: read normal data |
| data[1] = (head << 2) | drive; // HD DR1 DR2 |
| data[2] = track; |
| data[3] = head; |
| data[4] = sector; |
| data[5] = 2; // 512 byte sector size |
| data[6] = sector + num_sectors - 1; // last sector to read on track |
| data[7] = 0; // Gap length |
| data[8] = 0xff; // Gap length |
| |
| int ret = floppy_cmd(regs, (num_sectors * 512) - 1, data, 9); |
| if (ret) |
| goto fail; |
| |
| if (data[0] & 0xc0) { |
| floppy_ret(regs, DISK_RET_ECONTROLLER); |
| goto fail; |
| } |
| |
| // ??? should track be new val from return_status[3] ? |
| set_diskette_current_cyl(drive, track); |
| // AL = number of sectors read (same value as passed) |
| floppy_ret(regs, DISK_RET_SUCCESS); |
| return; |
| fail: |
| regs->al = 0; // no sectors read |
| } |
| |
| // Write Diskette Sectors |
| static void |
| floppy_1303(struct bregs *regs, u8 drive) |
| { |
| if (check_drive(regs, drive)) |
| goto fail; |
| |
| u8 num_sectors = regs->al; |
| u8 track = regs->ch; |
| u8 sector = regs->cl; |
| u8 head = regs->dh; |
| |
| if (head > 1 || sector == 0 || num_sectors == 0 |
| || track > 79 || num_sectors > 72) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| goto fail; |
| } |
| |
| // send write-normal-data command (9 bytes) to controller |
| u8 data[12]; |
| data[0] = 0xc5; // c5: write normal data |
| data[1] = (head << 2) | drive; // HD DR1 DR2 |
| data[2] = track; |
| data[3] = head; |
| data[4] = sector; |
| data[5] = 2; // 512 byte sector size |
| data[6] = sector + num_sectors - 1; // last sector to write on track |
| data[7] = 0; // Gap length |
| data[8] = 0xff; // Gap length |
| |
| int ret = floppy_cmd(regs, (num_sectors * 512) - 1, data, 9); |
| if (ret) |
| goto fail; |
| |
| if (data[0] & 0xc0) { |
| if (data[1] & 0x02) { |
| floppy_ret(regs, DISK_RET_EWRITEPROTECT); |
| goto fail; |
| } |
| BX_PANIC("int13_diskette_function: read error\n"); |
| } |
| |
| // ??? should track be new val from return_status[3] ? |
| set_diskette_current_cyl(drive, track); |
| // AL = number of sectors read (same value as passed) |
| floppy_ret(regs, DISK_RET_SUCCESS); |
| return; |
| fail: |
| regs->al = 0; // no sectors read |
| } |
| |
| // Verify Diskette Sectors |
| static void |
| floppy_1304(struct bregs *regs, u8 drive) |
| { |
| if (check_drive(regs, drive)) |
| goto fail; |
| |
| u8 num_sectors = regs->al; |
| u8 track = regs->ch; |
| u8 sector = regs->cl; |
| u8 head = regs->dh; |
| |
| if (head > 1 || sector == 0 || num_sectors == 0 |
| || track > 79 || num_sectors > 72) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| goto fail; |
| } |
| |
| // ??? should track be new val from return_status[3] ? |
| set_diskette_current_cyl(drive, track); |
| // AL = number of sectors verified (same value as passed) |
| floppy_ret(regs, DISK_RET_SUCCESS); |
| return; |
| fail: |
| regs->al = 0; // no sectors read |
| } |
| |
| // format diskette track |
| static void |
| floppy_1305(struct bregs *regs, u8 drive) |
| { |
| dprintf(3, "floppy f05\n"); |
| |
| if (check_drive(regs, drive)) |
| return; |
| |
| u8 num_sectors = regs->al; |
| u8 head = regs->dh; |
| |
| if (head > 1 || num_sectors == 0 || num_sectors > 18) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| return; |
| } |
| |
| // send format-track command (6 bytes) to controller |
| u8 data[12]; |
| data[0] = 0x4d; // 4d: format track |
| data[1] = (head << 2) | drive; // HD DR1 DR2 |
| data[2] = 2; // 512 byte sector size |
| data[3] = num_sectors; // number of sectors per track |
| data[4] = 0; // Gap length |
| data[5] = 0xf6; // Fill byte |
| |
| int ret = floppy_cmd(regs, (num_sectors * 4) - 1, data, 6); |
| if (ret) |
| return; |
| |
| if (data[0] & 0xc0) { |
| if (data[1] & 0x02) { |
| floppy_ret(regs, DISK_RET_EWRITEPROTECT); |
| return; |
| } |
| BX_PANIC("int13_diskette_function: read error\n"); |
| } |
| |
| set_diskette_current_cyl(drive, 0); |
| floppy_ret(regs, 0); |
| } |
| |
| // read diskette drive parameters |
| static void |
| floppy_1308(struct bregs *regs, u8 drive) |
| { |
| dprintf(3, "floppy f08\n"); |
| |
| u8 drive_type = inb_cmos(CMOS_FLOPPY_DRIVE_TYPE); |
| u8 num_floppies = 0; |
| if (drive_type & 0xf0) |
| num_floppies++; |
| if (drive_type & 0x0f) |
| num_floppies++; |
| |
| if (drive > 1) { |
| regs->ax = 0; |
| regs->bx = 0; |
| regs->cx = 0; |
| regs->dx = 0; |
| regs->es = 0; |
| regs->di = 0; |
| regs->dl = num_floppies; |
| set_fail(regs); |
| return; |
| } |
| |
| if (drive == 0) |
| drive_type >>= 4; |
| else |
| drive_type &= 0x0f; |
| |
| regs->bh = 0; |
| regs->bl = drive_type; |
| regs->ah = 0; |
| regs->al = 0; |
| regs->dl = num_floppies; |
| |
| switch (drive_type) { |
| case 0: // none |
| regs->cx = 0; |
| regs->dh = 0; // max head # |
| break; |
| |
| case 1: // 360KB, 5.25" |
| regs->cx = 0x2709; // 40 tracks, 9 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| case 2: // 1.2MB, 5.25" |
| regs->cx = 0x4f0f; // 80 tracks, 15 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| case 3: // 720KB, 3.5" |
| regs->cx = 0x4f09; // 80 tracks, 9 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| case 4: // 1.44MB, 3.5" |
| regs->cx = 0x4f12; // 80 tracks, 18 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| case 5: // 2.88MB, 3.5" |
| regs->cx = 0x4f24; // 80 tracks, 36 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| case 6: // 160k, 5.25" |
| regs->cx = 0x2708; // 40 tracks, 8 sectors |
| regs->dh = 0; // max head # |
| break; |
| |
| case 7: // 180k, 5.25" |
| regs->cx = 0x2709; // 40 tracks, 9 sectors |
| regs->dh = 0; // max head # |
| break; |
| |
| case 8: // 320k, 5.25" |
| regs->cx = 0x2708; // 40 tracks, 8 sectors |
| regs->dh = 1; // max head # |
| break; |
| |
| default: // ? |
| BX_PANIC("floppy: int13: bad floppy type\n"); |
| } |
| |
| /* set es & di to point to 11 byte diskette param table in ROM */ |
| regs->es = SEG_BIOS; |
| regs->di = (u32)&diskette_param_table2; |
| /* disk status not changed upon success */ |
| set_success(regs); |
| } |
| |
| // read diskette drive type |
| static void |
| floppy_1315(struct bregs *regs, u8 drive) |
| { |
| dprintf(6, "floppy f15\n"); |
| if (drive > 1) { |
| set_fail(regs); |
| regs->ah = 0; // only 2 drives supported |
| // set_diskette_ret_status here ??? |
| return; |
| } |
| u8 drive_type = get_drive_type(drive); |
| |
| regs->ah = (drive_type != 0); |
| set_success(regs); |
| } |
| |
| // get diskette change line status |
| static void |
| floppy_1316(struct bregs *regs, u8 drive) |
| { |
| if (drive > 1) { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| return; |
| } |
| floppy_ret(regs, DISK_RET_ECHANGED); |
| } |
| |
| static void |
| floppy_13XX(struct bregs *regs, u8 drive) |
| { |
| floppy_ret(regs, DISK_RET_EPARAM); |
| } |
| |
| void |
| floppy_13(struct bregs *regs, u8 drive) |
| { |
| if (! CONFIG_FLOPPY_SUPPORT) { |
| // Minimal stubs |
| switch (regs->ah) { |
| case 0x01: floppy_1301(regs, drive); break; |
| default: floppy_13XX(regs, drive); break; |
| } |
| return; |
| } |
| switch (regs->ah) { |
| case 0x00: floppy_1300(regs, drive); break; |
| case 0x01: floppy_1301(regs, drive); break; |
| case 0x02: floppy_1302(regs, drive); break; |
| case 0x03: floppy_1303(regs, drive); break; |
| case 0x04: floppy_1304(regs, drive); break; |
| case 0x05: floppy_1305(regs, drive); break; |
| case 0x08: floppy_1308(regs, drive); break; |
| case 0x15: floppy_1315(regs, drive); break; |
| case 0x16: floppy_1316(regs, drive); break; |
| default: floppy_13XX(regs, drive); break; |
| } |
| } |
| |
| // INT 0Eh Diskette Hardware ISR Entry Point |
| void VISIBLE16 |
| handle_0e() |
| { |
| debug_isr(DEBUG_ISR_0e); |
| if (! CONFIG_FLOPPY_SUPPORT) |
| goto done; |
| |
| if ((inb(PORT_FD_STATUS) & 0xc0) != 0xc0) { |
| outb(0x08, PORT_FD_DATA); // sense interrupt status |
| while ((inb(PORT_FD_STATUS) & 0xc0) != 0xc0) |
| ; |
| do { |
| inb(PORT_FD_DATA); |
| } while ((inb(PORT_FD_STATUS) & 0xc0) == 0xc0); |
| } |
| // diskette interrupt has occurred |
| SETBITS_BDA(floppy_recalibration_status, FRS_TIMEOUT); |
| |
| done: |
| eoi_pic1(); |
| } |
| |
| // Called from int08 handler. |
| void |
| floppy_tick() |
| { |
| if (! CONFIG_FLOPPY_SUPPORT) |
| return; |
| |
| // time to turn off drive(s)? |
| u8 fcount = GET_BDA(floppy_motor_counter); |
| if (fcount) { |
| fcount--; |
| SET_BDA(floppy_motor_counter, fcount); |
| if (fcount == 0) |
| // turn motor(s) off |
| outb(inb(PORT_FD_DOR) & 0xcf, PORT_FD_DOR); |
| } |
| } |