Matt DeVillier | 0d58e64 | 2020-03-31 13:12:22 -0500 | [diff] [blame] | 1 | chip soc/intel/skylake |
| 2 | |
| 3 | register "ScsSdCardEnabled" = "2" |
| 4 | |
| 5 | register "PmConfigSlpS4MinAssert" = "1" # 1s |
| 6 | register "PmConfigSlpSusMinAssert" = "1" # 500ms |
| 7 | |
| 8 | register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port (board) |
| 9 | register "usb2_ports[1]" = "USB2_PORT_MAX(OC_SKIP)" # Type-C Port (flex) |
| 10 | register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth |
| 11 | register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Type-A Port 1 |
| 12 | register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera |
| 13 | register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Type-A Port 2 |
| 14 | |
| 15 | register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (board) |
| 16 | register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (flex) |
| 17 | register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Type-A Port 1 |
| 18 | register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Type-A Port 2 |
| 19 | |
| 20 | # PL2 override 15W |
Sumeet R Pawnikar | 97c5464 | 2020-05-10 01:24:11 +0530 | [diff] [blame^] | 21 | register "power_limits_config" = "{ |
| 22 | .tdp_pl2_override = 15, |
| 23 | }" |
Matt DeVillier | 0d58e64 | 2020-03-31 13:12:22 -0500 | [diff] [blame] | 24 | |
| 25 | # Send an extra VR mailbox command for the supported MPS IMVP8 model |
| 26 | register "SendVrMbxCmd" = "1" |
| 27 | |
| 28 | # TCC of 90C |
| 29 | register "tcc_offset" = "10" |
| 30 | |
| 31 | # Use default SD card detect GPIO configuration |
| 32 | register "sdcard_cd_gpio_default" = "GPP_A7" |
| 33 | |
| 34 | device domain 0 on |
| 35 | device pci 15.0 on |
| 36 | chip drivers/i2c/generic |
| 37 | register "hid" = ""ELAN0001"" |
| 38 | register "desc" = ""ELAN Touchscreen"" |
| 39 | register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" |
| 40 | device i2c 10 on end |
| 41 | end |
| 42 | end # I2C #0 |
| 43 | device pci 15.1 on |
| 44 | chip drivers/i2c/generic |
| 45 | register "hid" = ""ELAN0000"" |
| 46 | register "desc" = ""ELAN Touchpad"" |
| 47 | register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" |
| 48 | register "wake" = "GPE0_DW0_05" |
| 49 | device i2c 15 on end |
| 50 | end |
| 51 | end # I2C #1 |
| 52 | device pci 19.2 on |
| 53 | chip drivers/i2c/nau8825 |
| 54 | register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" |
| 55 | register "jkdet_enable" = "1" |
| 56 | register "jkdet_pull_enable" = "0" # R389 |
| 57 | register "jkdet_polarity" = "1" # ActiveLow |
| 58 | register "vref_impedance" = "2" # 125kOhm |
| 59 | register "micbias_voltage" = "6" # 2.754 |
| 60 | register "sar_threshold_num" = "4" |
| 61 | register "sar_threshold[0]" = "0x0c" |
| 62 | register "sar_threshold[1]" = "0x1e" |
| 63 | register "sar_threshold[2]" = "0x38" |
| 64 | register "sar_threshold[3]" = "0x60" |
| 65 | register "sar_hysteresis" = "1" |
| 66 | register "sar_voltage" = "0" # VDDA |
| 67 | register "sar_compare_time" = "0" # 500ns |
| 68 | register "sar_sampling_time" = "0" # 2us |
| 69 | register "short_key_debounce" = "2" # 100ms |
| 70 | register "jack_insert_debounce" = "7" # 512ms |
| 71 | register "jack_eject_debounce" = "7" # 512ms |
| 72 | device i2c 1a on end |
| 73 | end |
| 74 | end # I2C #4 |
| 75 | device pci 1e.6 on end # SDCard |
| 76 | device pci 1f.3 on |
| 77 | chip drivers/generic/max98357a |
| 78 | register "hid" = ""MX98357A"" |
| 79 | register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" |
| 80 | register "sdmode_delay" = "5" |
| 81 | device generic 0 on end |
| 82 | end |
| 83 | end # Intel HDA |
| 84 | end |
| 85 | end |