src/mainboard/google/dedede/variants/bugzzy/overridetree.cb

chip soc/intel/jasperlake
	# MIPI display panel
	register "DdiPortAConfig" = "2" # DdiPortMipiDsi

	# Disable PCIe Root Port 8 (index 7)
	register "PcieRpEnable[7]" = "0"
	# Disable PCIe Clock Source 4 (index 3)
	register "PcieClkSrcUsage[3]" = "0xff"

	# USB Port Configuration
	register "usb2_ports[0]" = "{
		.enable = 1,
		.ocpin = OC_SKIP,
		.tx_bias = USB2_BIAS_0MV,
		.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
		.pre_emp_bias  = USB2_BIAS_28P15MV,
		.pre_emp_bit   = USB2_HALF_BIT_PRE_EMP,
	}" # Type-C Port C0
	register "usb2_ports[1]" = "{
		.enable = 1,
		.ocpin = OC_SKIP,
		.tx_bias = USB2_BIAS_16P9MV,
		.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
		.pre_emp_bias  = USB2_BIAS_39P35MV,
		.pre_emp_bit   = USB2_HALF_BIT_PRE_EMP,
	}" # Type-C Port C1
	register "usb2_ports[2]" = "{
		.enable = 1,
		.ocpin = OC_SKIP,
		.tx_bias = USB2_BIAS_11P25MV,
		.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON,
		.pre_emp_bias  = USB2_BIAS_11P25MV,
		.pre_emp_bit   = USB2_HALF_BIT_PRE_EMP,
	}" # Type-A Port A0
	register "usb2_ports[3]" = "USB2_PORT_EMPTY"
	register "usb2_ports[4]" = "USB2_PORT_EMPTY"
	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)"	# Camera

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI0             | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#|                   | before memory is up       |
	#| I2C0              | Trackpad                  |
	#| I2C1              | Digitizer                 |
	#| I2C2              | Touchscreen               |
	#| I2C3              | Camera                    |
	#| I2C4              | Audio                     |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.panel_orientation = LB_FB_ORIENTATION_RIGHT_UP,
		.gspi[0] = {
			.speed_mhz = 1,
			.early_init = 1,
		},
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 209,
			.fall_time_ns = 12,
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[2] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[4] = {
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 175,
			.fall_time_ns = 8,
		},
	}"
	device domain 0 on
		device pci 04.0 on
			chip drivers/intel/dptf
				register "options.tsr[0].desc" = ""Memory""
				register "options.tsr[1].desc" = ""CPU""
				register "options.tsr[2].desc" = ""Charger""
				register "options.tsr[3].desc" = ""LTE""
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU, CPU,           90, 10000),
					[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 100, 60000),
					[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 100, 15000),
					[3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 60, 15000),
					[4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 100, 15000),
				}"
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,           105, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 100, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 100, SHUTDOWN),
					[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 100, SHUTDOWN),
				}"
				register "controls.power_limits" = "{
					.pl1 = {
						.min_power = 6000,
						.max_power = 6000,
						.time_window_min = 1 * MSECS_PER_SEC,
						.time_window_max = 1 * MSECS_PER_SEC,
						.granularity = 200,
					},
					.pl2 = {
						.min_power = 20000,
						.max_power = 20000,
						.time_window_min = 1 * MSECS_PER_SEC,
						.time_window_max = 1 * MSECS_PER_SEC,
						.granularity = 1000,
					}
				}"
				register "controls.charger_perf" = "{
					[0] = { 255, 2800 },
					[1] = {  39, 2500 },
					[2] = {  31, 2000 },
					[3] = {  23, 1500 },
				}"
				device generic 0 on end
			end
		end # SA Thermal device
		device pci 05.0 on # IPU - MIPI Camera
			chip drivers/intel/mipi_camera
				register "acpi_uid" = "0x50000"
				register "acpi_name" = ""IPU0""
				register "device_type" = "INTEL_ACPI_CAMERA_CIO2"

				register "cio2_num_ports" = "2"
				register "cio2_lanes_used" = "{1,4}"
				register "cio2_lane_endpoint[1]" = ""^I2C3.CAM1""
				register "cio2_prt[0]" = "0"
				register "cio2_prt[1]" = "2"
				device generic 0 on end
			end
		end
		device pci 14.0 on
			chip drivers/usb/acpi
				device usb 0.0 on
					chip drivers/usb/acpi
						register "desc" = ""UFCamera""
						register "type" = "UPC_TYPE_INTERNAL"
						register "has_power_resource" = "1"
						register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D13)"
						register "enable_delay_ms" = "20"
						device usb 2.5 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""LTE""
						register "type" = "UPC_TYPE_INTERNAL"
						register "has_power_resource" = "1"
						register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)"
						register "reset_off_delay_ms" = "20"
						register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)"
						register "enable_delay_ms" = "20"
						device usb 3.3 on
							probe DB_PORTS DB_PORTS_1C_1A_LTE
						end
					end
				end
			end
		end # USB xHCI
		device pci 15.0 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)"
				register "wake" = "GPE0_DW0_03"
				register "probed" = "1"
				device i2c 15 on end
			end
			chip drivers/i2c/hid
				register "generic.hid" = ""ZNT0000""
				register "generic.desc" = ""Zinitix Touchpad""
				register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)"
				register "generic.wake" = "GPE0_DW0_03"
				register "generic.probed" = "1"
				register "hid_desc_reg_offset" = "0xE"
				device i2c 40 on end
			end
		end # I2C 0
		device pci 15.1 on
			chip drivers/i2c/hid
				register "generic.hid" = ""WCOM014B""
				register "generic.desc" = ""WCOM Digitizer""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D7_IRQ)"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)"
				register "generic.enable_delay_ms" = "20"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E1)"
				register "generic.reset_delay_ms" = "100"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x1"
				device i2c 0x09 on end
			end
		end # I2C #1
		device pci 15.2 on
			chip drivers/i2c/hid
				register "generic.hid" = ""HX121A""
				register "generic.desc" = ""HX Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)"
				register "generic.probed" = "1"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)"
				register "generic.reset_delay_ms" = "120"
				register "generic.reset_off_delay_ms" = "2"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x1"
				device i2c 0x4F on end
			end
		end # I2C #2
		device pci 15.3 on
			chip drivers/intel/mipi_camera
				register "acpi_hid" = ""OVTI8856""
				register "acpi_uid" = "0"
				register "acpi_name" = ""CAM1""
				register "chip_name" = ""Ov 8856 Camera""
				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"

				register "ssdb.lanes_used" = "4"
				register "ssdb.link_used" = "1"
				register "ssdb.vcm_type" = "0x0C"
				register "vcm_name" = ""VCM0""
				register "num_freq_entries" = "2"
				register "link_freq[0]" = "360000000"
				register "link_freq[1]" = "180000000"
				register "remote_name" = ""IPU0""

				register "has_power_resource" = "1"
				#Controls
				register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1
				register "clk_panel.clks[0].freq" = "1" #19.2 Mhz

				register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #power_enable_2p8
				register "gpio_panel.gpio[1].gpio_num" = "GPP_D14" #power_enable_1p2
				register "gpio_panel.gpio[2].gpio_num" = "GPP_D12" #reset

				#_ON
				register "on_seq.ops_cnt" = "5"
				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)"
				register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)"

				#_OFF
				register "off_seq.ops_cnt" = "4"
				register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
				register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

				device i2c 36 on end
			end
			chip drivers/intel/mipi_camera
				register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
				register "acpi_uid" = "3"
				register "acpi_name" = ""VCM0""
				register "chip_name" = ""DW AF DAC""
				register "device_type" = "INTEL_ACPI_CAMERA_VCM"

				register "pr0" = ""\\_SB.PCI0.I2C3.CAM1.PRIC""
				register "vcm_compat" = ""dongwoon,dw9714""

				device i2c 0C on end
			end
			chip drivers/intel/mipi_camera
				register "acpi_uid" = "1"
				register "acpi_name" = ""NVM0""
				register "chip_name" = ""GT24C08""
				register "device_type" = "INTEL_ACPI_CAMERA_NVM"

				register "nvm_size" = "0x2000"
				register "nvm_pagesize" = "1"
				register "nvm_readonly" = "1"
				register "nvm_width" = "0x10"
				register "nvm_compat" = ""atmel,24c08""

				device i2c 50 on end
			end
		end # I2C 3
		device pci 1c.7 off end # PCI Express Root Port 8
		device pci 19.0 on
			chip drivers/i2c/da7219
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)"
				register "btn_cfg" = "50"
				register "mic_det_thr" = "500"
				register "jack_ins_deb" = "20"
				register "jack_det_rate" = ""32ms_64ms""
				register "jack_rem_deb" = "1"
				register "a_d_btn_thr" = "0xa"
				register "d_b_btn_thr" = "0x16"
				register "b_c_btn_thr" = "0x21"
				register "c_mic_btn_thr" = "0x3e"
				register "btn_avg" = "4"
				register "adc_1bit_rpt" = "1"
				register "micbias_lvl" = "2600"
				register "mic_amp_in_sel" = ""diff""
				device i2c 1a on end
			end
		end #I2C 4
		device pci 1f.3 on
			chip drivers/generic/max98357a
				register "hid" = ""MX98360A""
				register "sdmode_gpio" =  "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)"
				device generic 0 on end
			end
		end # Intel HDA
	end
end