Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 1 | fw_config |
Morris Hsu | 0360aea | 2023-10-18 15:45:18 +0800 | [diff] [blame] | 2 | field FP_MCU 9 10 |
| 3 | option FP_ABSENT 0 |
| 4 | option FP_MCU_NUVOTON 1 |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 5 | end |
| 6 | field STORAGE 30 31 |
| 7 | option STORAGE_UNKNOWN 0 |
| 8 | option STORAGE_UFS 1 |
| 9 | option STORAGE_NVME 2 |
| 10 | end |
| 11 | end |
Morris Hsu | 5ccc527 | 2023-09-11 13:20:37 +0800 | [diff] [blame] | 12 | chip soc/intel/alderlake |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 13 | register "sagv" = "SaGv_Enabled" |
| 14 | |
| 15 | # As per Intel Advisory doc#723158, the change is required to prevent possible |
| 16 | # display flickering issue. |
| 17 | register "disable_dynamic_tccold_handshake" = "true" |
| 18 | |
| 19 | # SOC Aux orientation override: |
| 20 | # This is a bitfield that corresponds to up to 4 TCSS ports. |
Morris Hsu | 0cf76cf | 2023-11-30 13:56:26 +0800 | [diff] [blame] | 21 | # Bits (0,1) allocated for TCSS Port1 configuration, Bits (4,5)for TCSS Port3. |
| 22 | # TcssAuxOri = 010001b |
| 23 | # Bit0,Bit4 set to "1" indicates no retimer on USBC Ports, otherwise is "0" |
| 24 | # Bit1,Bit5 set to "0" indicates Aux lines are not swapped on the |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 25 | # motherboard to USBC connector |
Morris Hsu | 0cf76cf | 2023-11-30 13:56:26 +0800 | [diff] [blame] | 26 | register "tcss_aux_ori" = "0x11" |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 27 | register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
Morris Hsu | 0cf76cf | 2023-11-30 13:56:26 +0800 | [diff] [blame] | 28 | register "typec_aux_bias_pads[2]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 29 | |
| 30 | register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2 Port 1 |
| 31 | register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable USB2 Port 3 |
| 32 | register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2 Port 4 |
| 33 | register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 6 |
| 34 | |
| 35 | register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Disable USB3/2 Type A port3 |
| 36 | register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Disable M.2 WWAN |
| 37 | |
| 38 | # FIVR configurations are disabled since the board doesn't have V1p05 and Vnn |
| 39 | # bypass rails implemented. |
| 40 | register "ext_fivr_settings" = "{ |
| 41 | .configure_ext_fivr = 1, |
| 42 | }" |
| 43 | |
| 44 | # Enable the Cnvi BT Audio Offload |
| 45 | register "cnvi_bt_audio_offload" = "1" |
| 46 | |
| 47 | # Intel Common SoC Config |
| 48 | #+-------------------+---------------------------+ |
| 49 | #| Field | Value | |
| 50 | #+-------------------+---------------------------+ |
| 51 | #| GSPI1 | Fingerprint MCU | |
| 52 | #| I2C0 | Audio | |
| 53 | #| I2C1 | cr50 TPM. Early init is | |
| 54 | #| | required to set up a BAR | |
| 55 | #| | for TPM communication | |
| 56 | #| I2C3 | TouchScreen | |
| 57 | #| I2C5 | Trackpad | |
| 58 | #+-------------------+---------------------------+ |
| 59 | register "common_soc_config" = "{ |
| 60 | .i2c[0] = { |
| 61 | .speed = I2C_SPEED_FAST, |
| 62 | }, |
| 63 | .i2c[1] = { |
| 64 | .early_init = 1, |
| 65 | .speed = I2C_SPEED_FAST, |
| 66 | .rise_time_ns = 550, |
| 67 | .fall_time_ns = 400, |
| 68 | .data_hold_time_ns = 50, |
| 69 | }, |
| 70 | .i2c[2] = { |
| 71 | .speed = I2C_SPEED_FAST, |
| 72 | }, |
| 73 | .i2c[3] = { |
| 74 | .speed = I2C_SPEED_FAST, |
| 75 | .rise_time_ns = 550, |
| 76 | .fall_time_ns = 400, |
| 77 | .data_hold_time_ns = 50, |
| 78 | }, |
| 79 | .i2c[5] = { |
| 80 | .speed = I2C_SPEED_FAST, |
| 81 | }, |
| 82 | }" |
Morris Hsu | 5ccc527 | 2023-09-11 13:20:37 +0800 | [diff] [blame] | 83 | |
| 84 | device domain 0 on |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 85 | device ref tbt_pcie_rp0 off end |
| 86 | device ref tbt_pcie_rp1 off end |
| 87 | device ref tbt_pcie_rp2 off end |
| 88 | device ref tcss_dma0 off end |
| 89 | device ref tcss_dma1 off end |
| 90 | device ref igpu on |
| 91 | chip drivers/gfx/generic |
| 92 | register "device_count" = "6" |
| 93 | # DDIA for eDP |
Matt DeVillier | 4e685bf | 2024-01-19 20:37:58 -0600 | [diff] [blame^] | 94 | register "device[0].name" = ""LCD0"" |
Matt DeVillier | cf29efa | 2024-01-16 18:46:20 -0600 | [diff] [blame] | 95 | # Internal panel on the first port of the graphics chip |
| 96 | register "device[0].addr" = "0x80010400" |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 97 | # DDIB for HDMI |
| 98 | register "device[1].name" = ""DD01"" |
| 99 | # TCP0 (DP-1) for port C0 |
| 100 | register "device[2].name" = ""DD02"" |
| 101 | register "device[2].use_pld" = "true" |
| 102 | register "device[2].pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| 103 | # TCP1 (DP-2) is unused for any ports but still enumerated in the kernel, so GFX device is added for TCP1 |
| 104 | register "device[3].name" = ""DD03"" |
| 105 | # TCP2 (DP-3) for port C1 |
| 106 | register "device[4].name" = ""DD04"" |
| 107 | register "device[4].use_pld" = "true" |
| 108 | register "device[4].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| 109 | # TCP3 (DP-4) is unused for any ports but still enumerated in the kernel, so GFX device is added for TCP3 |
| 110 | register "device[5].name" = ""DD05"" |
| 111 | device generic 0 on end |
| 112 | end |
| 113 | end # Integrated Graphics Device |
| 114 | device ref dtt on |
| 115 | chip drivers/intel/dptf |
| 116 | ## sensor information |
| 117 | register "options.tsr[0].desc" = ""DRAM"" |
| 118 | register "options.tsr[1].desc" = ""Soc"" |
| 119 | register "options.tsr[2].desc" = ""Charger"" |
| 120 | |
| 121 | # TODO: below values are initial reference values only |
| 122 | ## Active Policy |
| 123 | register "policies.active" = "{ |
| 124 | [0] = { |
| 125 | .target = DPTF_CPU, |
| 126 | .thresholds = { |
| 127 | TEMP_PCT(85, 90), |
| 128 | TEMP_PCT(75, 80), |
| 129 | TEMP_PCT(68, 70), |
| 130 | TEMP_PCT(62, 60), |
| 131 | TEMP_PCT(55, 50), |
| 132 | TEMP_PCT(50, 40), |
| 133 | TEMP_PCT(40, 30), |
| 134 | } |
| 135 | }, |
| 136 | [1] = { |
| 137 | .target = DPTF_TEMP_SENSOR_1, |
| 138 | .thresholds = { |
| 139 | TEMP_PCT(60, 90), |
| 140 | TEMP_PCT(55, 80), |
| 141 | TEMP_PCT(52, 70), |
| 142 | TEMP_PCT(48, 60), |
| 143 | TEMP_PCT(44, 50), |
| 144 | TEMP_PCT(40, 40), |
| 145 | TEMP_PCT(36, 30), |
| 146 | } |
| 147 | } |
| 148 | }" |
| 149 | |
| 150 | ## Passive Policy |
| 151 | register "policies.passive" = "{ |
| 152 | [0] = DPTF_PASSIVE(CPU, CPU, 90, 5000), |
| 153 | [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 55, 5000), |
| 154 | [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 55, 5000), |
| 155 | [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 55, 5000), |
| 156 | }" |
| 157 | |
| 158 | ## Critical Policy |
| 159 | register "policies.critical" = "{ |
| 160 | [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), |
| 161 | [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| 162 | [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| 163 | [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| 164 | }" |
| 165 | |
| 166 | register "controls.power_limits" = "{ |
| 167 | .pl1 = { |
| 168 | .min_power = 18000, |
| 169 | .max_power = 28000, |
| 170 | .time_window_min = 28 * MSECS_PER_SEC, |
| 171 | .time_window_max = 32 * MSECS_PER_SEC, |
| 172 | .granularity = 200, |
| 173 | }, |
| 174 | .pl2 = { |
| 175 | .min_power = 40000, |
| 176 | .max_power = 40000, |
| 177 | .time_window_min = 28 * MSECS_PER_SEC, |
| 178 | .time_window_max = 32 * MSECS_PER_SEC, |
| 179 | .granularity = 1000, |
| 180 | } |
| 181 | }" |
| 182 | |
| 183 | ## Charger Performance Control (Control, mA) |
| 184 | register "controls.charger_perf" = "{ |
| 185 | [0] = { 255, 1700 }, |
| 186 | [1] = { 24, 1500 }, |
| 187 | [2] = { 16, 1000 }, |
| 188 | [3] = { 8, 500 } |
| 189 | }" |
| 190 | |
| 191 | ## Fan Performance Control (Percent, Speed, Noise, Power) |
| 192 | register "controls.fan_perf" = "{ |
| 193 | [0] = { 90, 6700, 220, 2200, }, |
| 194 | [1] = { 80, 5800, 180, 1800, }, |
| 195 | [2] = { 70, 5000, 145, 1450, }, |
| 196 | [3] = { 60, 4900, 115, 1150, }, |
| 197 | [4] = { 50, 3838, 90, 900, }, |
| 198 | [5] = { 40, 2904, 55, 550, }, |
| 199 | [6] = { 30, 2337, 30, 300, }, |
| 200 | [7] = { 20, 1608, 15, 150, }, |
| 201 | [8] = { 10, 800, 10, 100, }, |
| 202 | [9] = { 0, 0, 0, 50, } |
| 203 | }" |
| 204 | |
| 205 | ## Fan options |
| 206 | register "options.fan.fine_grained_control" = "1" |
| 207 | register "options.fan.step_size" = "2" |
| 208 | |
| 209 | device generic 0 alias dptf_policy on end |
| 210 | end |
| 211 | end |
| 212 | device ref pcie4_0 on |
| 213 | # Enable CPU PCIE RP 1 using CLK 0 |
| 214 | register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| 215 | .clk_req = 0, |
| 216 | .clk_src = 0, |
| 217 | .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| 218 | }" |
| 219 | probe STORAGE STORAGE_UNKNOWN |
| 220 | probe STORAGE STORAGE_NVME |
| 221 | end |
| 222 | device ref pcie_rp5 off end |
| 223 | device ref pcie_rp6 off end |
| 224 | device ref pcie_rp8 off end |
| 225 | device ref cnvi_wifi on |
| 226 | chip drivers/wifi/generic |
| 227 | register "wake" = "GPE0_PME_B0" |
| 228 | device generic 0 on end |
| 229 | end |
| 230 | end |
| 231 | device ref i2c0 on |
| 232 | chip drivers/i2c/generic |
| 233 | register "hid" = ""10EC5650"" |
| 234 | register "name" = ""RT58"" |
| 235 | register "desc" = ""Realtek RT5650"" |
| 236 | register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| 237 | register "property_count" = "1" |
| 238 | register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| 239 | register "property_list[0].name" = ""realtek,jd-mode"" |
| 240 | register "property_list[0].integer" = "2" |
| 241 | device i2c 1a on end |
| 242 | end |
| 243 | end # I2C0 |
| 244 | device ref i2c1 on |
| 245 | chip drivers/i2c/tpm |
| 246 | register "hid" = ""GOOG0005"" |
| 247 | register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| 248 | device i2c 50 on end |
| 249 | end |
| 250 | end |
Morris Hsu | 0ec65da | 2023-10-25 14:31:10 +0800 | [diff] [blame] | 251 | device ref i2c3 on |
| 252 | chip drivers/i2c/hid |
| 253 | register "generic.hid" = ""ILTK0001"" |
| 254 | register "generic.desc" = ""ILITEK Touchscreen"" |
| 255 | register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| 256 | register "generic.detect" = "1" |
| 257 | register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| 258 | register "generic.reset_delay_ms" = "200" |
| 259 | register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| 260 | register "generic.enable_delay_ms" = "12" |
| 261 | register "generic.has_power_resource" = "1" |
| 262 | register "hid_desc_reg_offset" = "0x01" |
| 263 | device i2c 41 on end |
| 264 | end |
| 265 | chip drivers/i2c/hid |
| 266 | register "generic.hid" = ""ELAN9004"" |
| 267 | register "generic.desc" = ""ELAN Touchscreen"" |
| 268 | register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| 269 | register "generic.detect" = "1" |
| 270 | register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| 271 | register "generic.reset_delay_ms" = "20" |
| 272 | register "generic.reset_off_delay_ms" = "2" |
| 273 | register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| 274 | register "generic.enable_delay_ms" = "1" |
| 275 | register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| 276 | register "generic.stop_delay_ms" = "150" |
| 277 | register "generic.stop_off_delay_ms" = "2" |
| 278 | register "generic.has_power_resource" = "1" |
| 279 | register "hid_desc_reg_offset" = "0x01" |
| 280 | device i2c 10 on end |
| 281 | end |
| 282 | end |
Morris Hsu | a0efce4 | 2023-10-18 17:58:04 +0800 | [diff] [blame] | 283 | device ref i2c5 on |
| 284 | chip drivers/i2c/generic |
| 285 | register "hid" = ""ELAN0000"" |
| 286 | register "desc" = ""ELAN Touchpad"" |
| 287 | register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| 288 | register "wake" = "GPE0_DW2_14" |
| 289 | register "detect" = "1" |
| 290 | device i2c 15 on end |
| 291 | end |
| 292 | chip drivers/i2c/hid |
| 293 | register "generic.hid" = ""SYNA0000"" |
| 294 | register "generic.cid" = ""ACPI0C50"" |
| 295 | register "generic.desc" = ""Synaptics Touchpad"" |
| 296 | register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| 297 | register "generic.wake" = "GPE0_DW2_14" |
| 298 | register "generic.detect" = "1" |
| 299 | register "hid_desc_reg_offset" = "0x20" |
| 300 | device i2c 0x2c on end |
| 301 | end |
| 302 | end |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 303 | device ref gspi1 on |
| 304 | chip drivers/spi/acpi |
| 305 | register "name" = ""CRFP"" |
| 306 | register "hid" = "ACPI_DT_NAMESPACE_HID" |
| 307 | register "uid" = "1" |
| 308 | register "compat_string" = ""google,cros-ec-spi"" |
| 309 | register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" |
| 310 | register "wake" = "GPE0_DW2_15" |
| 311 | register "has_power_resource" = "1" |
| 312 | register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)" |
| 313 | register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)" |
| 314 | register "enable_delay_ms" = "3" |
| 315 | device spi 0 on |
Morris Hsu | 0360aea | 2023-10-18 15:45:18 +0800 | [diff] [blame] | 316 | probe FP_MCU FP_MCU_NUVOTON |
Morris Hsu | 2fa482d | 2023-10-03 14:17:13 +0800 | [diff] [blame] | 317 | end |
| 318 | end # FPMCU |
| 319 | end |
| 320 | device ref pch_espi on |
| 321 | chip ec/google/chromeec |
| 322 | use conn0 as mux_conn[0] |
| 323 | use conn1 as mux_conn[1] |
| 324 | device pnp 0c09.0 on end |
| 325 | end |
| 326 | end |
| 327 | device ref ish on |
| 328 | chip drivers/intel/ish |
| 329 | register "add_acpi_dma_property" = "true" |
| 330 | device generic 0 on end |
| 331 | end |
| 332 | probe STORAGE STORAGE_UNKNOWN |
| 333 | probe STORAGE STORAGE_UFS |
| 334 | end |
| 335 | device ref ufs on |
| 336 | probe STORAGE STORAGE_UNKNOWN |
| 337 | probe STORAGE STORAGE_UFS |
| 338 | end |
| 339 | device ref pmc hidden |
| 340 | chip drivers/intel/pmc_mux |
| 341 | device generic 0 on |
| 342 | chip drivers/intel/pmc_mux/conn |
| 343 | use usb2_port1 as usb2_port |
| 344 | use tcss_usb3_port1 as usb3_port |
| 345 | device generic 0 alias conn0 on end |
| 346 | end |
| 347 | chip drivers/intel/pmc_mux/conn |
| 348 | use usb2_port3 as usb2_port |
| 349 | use tcss_usb3_port3 as usb3_port |
| 350 | device generic 1 alias conn1 on end |
| 351 | end |
| 352 | end |
| 353 | end |
| 354 | end |
| 355 | device ref tcss_xhci on |
| 356 | chip drivers/usb/acpi |
| 357 | device ref tcss_root_hub on |
| 358 | chip drivers/usb/acpi |
| 359 | register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| 360 | register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| 361 | register "use_custom_pld" = "true" |
| 362 | register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| 363 | device ref tcss_usb3_port1 on end |
| 364 | end |
| 365 | chip drivers/usb/acpi |
| 366 | register "desc" = ""USB3 Type-C Port C1 (MLB)"" |
| 367 | register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| 368 | register "use_custom_pld" = "true" |
| 369 | register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| 370 | register "usb_lpm_incapable" = "true" |
| 371 | device ref tcss_usb3_port3 on end |
| 372 | end |
| 373 | end |
| 374 | end |
| 375 | end |
| 376 | device ref xhci on |
| 377 | chip drivers/usb/acpi |
| 378 | device ref xhci_root_hub on |
| 379 | chip drivers/usb/acpi |
| 380 | register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| 381 | register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| 382 | register "use_custom_pld" = "true" |
| 383 | register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| 384 | device ref usb2_port1 on end |
| 385 | end |
| 386 | chip drivers/usb/acpi |
| 387 | register "desc" = ""USB2 Type-C Port C1 (MLB)"" |
| 388 | register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| 389 | register "use_custom_pld" = "true" |
| 390 | register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| 391 | device ref usb2_port3 on end |
| 392 | end |
| 393 | chip drivers/usb/acpi |
| 394 | register "desc" = ""USB2 Camera"" |
| 395 | register "type" = "UPC_TYPE_INTERNAL" |
| 396 | device ref usb2_port6 on end |
| 397 | end |
| 398 | chip drivers/usb/acpi |
| 399 | register "desc" = ""USB2 Type-A Port A0 (DB)"" |
| 400 | register "type" = "UPC_TYPE_A" |
| 401 | register "use_custom_pld" = "true" |
| 402 | register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))" |
| 403 | device ref usb2_port9 on end |
| 404 | end |
| 405 | chip drivers/usb/acpi |
| 406 | register "desc" = ""USB2 Bluetooth"" |
| 407 | register "type" = "UPC_TYPE_INTERNAL" |
| 408 | register "reset_gpio" = |
| 409 | "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| 410 | device ref usb2_port10 on end |
| 411 | end |
| 412 | chip drivers/usb/acpi |
| 413 | register "desc" = ""USB3 Type-A Port A0 (DB)"" |
| 414 | register "type" = "UPC_TYPE_USB3_A" |
| 415 | register "use_custom_pld" = "true" |
| 416 | register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(1, 2))" |
| 417 | device ref usb3_port1 on end |
| 418 | end |
| 419 | end |
| 420 | end |
| 421 | end |
Morris Hsu | 5ccc527 | 2023-09-11 13:20:37 +0800 | [diff] [blame] | 422 | end |
| 423 | |
| 424 | end |