src/mainboard/google/brya/variants/nereid/overridetree.cb

fw_config
	field DB_USB 0 1
		option DB_NONE		0
		option DB_1C_1A		1
		option DB_1A_HDMI	3
	end
end

chip soc/intel/alderlake
	register "sagv" = "SaGv_Enabled"

	# Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
	# Bit 2 - C1 has a redriver which does SBU muxing.
	# Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
	register "tcss_aux_ori" = "1"

	register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"

	register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)"	# WFC
	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)"	# Bluetooth port for PCIe WLAN
	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)"	# Bluetooth port for CNVi WLAN

        # Configure external V1P05/Vnn/VnnSx Rails
        register "ext_fivr_settings" = "{
                .configure_ext_fivr = 1,
                .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX,
                .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
                .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
                .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
                .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
                .v1p05_voltage_mv = 1050,
                .vnn_voltage_mv = 780,
                .vnn_sx_voltage_mv = 1050,
                .v1p05_icc_max_ma = 500,
                .vnn_icc_max_ma = 500,
        }"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| I2C0              | TPM. Early init is        |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#| I2C1              | Touchscreen               |
	#| I2C2              | Sub-board(PSensor)/WCAM   |
	#| I2C3              | Audio                     |
	#| I2C5              | Trackpad                  |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 158,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
		.i2c[1] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 160,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 157,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.speed_config[0] = {
				.speed = I2C_SPEED_FAST,
				.scl_lcnt = 152,
				.scl_hcnt = 79,
				.sda_hold = 7,
			}
		},
	}"

	device domain 0 on
		device ref dtt on
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""Memory""
				register "options.tsr[1].desc" = ""Charger""
				register "options.tsr[2].desc" = ""Ambient""

				# TODO: below values are initial reference values only
				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           95, 5000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 75, 5000),
					[2] = DPTF_PASSIVE(CHARGER,     TEMP_SENSOR_1, 75, 5000),
					[3] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_2, 75, 5000),
				}"

				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               105, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,      85, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,      85, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,      85, SHUTDOWN),
				}"

				register "controls.power_limits" = "{
					.pl1 = {
							.min_power = 3000,
							.max_power = 6000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 200
						},
					.pl2 = {
							.min_power = 25000,
							.max_power = 25000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 1000
						}
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"

				device generic 0 on end
			end
		end
		device ref i2c1 on
			chip drivers/i2c/hid
				register "generic.hid" = ""GDIX0000""
				register "generic.desc" = ""Goodix Touchscreen""
				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
				register "generic.probed" = "1"
				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
				register "generic.enable_delay_ms" = "20"
				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
				register "generic.reset_delay_ms" = "180"
				register "generic.reset_off_delay_ms" = "3"
				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
				register "generic.stop_off_delay_ms" = "1"
				register "generic.has_power_resource" = "1"
				register "hid_desc_reg_offset" = "0x01"
				device i2c 5d on end
			end
			chip drivers/generic/gpio_keys
				register "name" = ""PENH""
				register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)"
				register "key.wake_gpe" = "GPE0_DW2_15"
				register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
				register "key.wakeup_event_action" = "EV_ACT_ANY"
				register "key.dev_name" = ""EJCT""
				register "key.linux_code" = "SW_PEN_INSERTED"
				register "key.linux_input_type" = "EV_SW"
				register "key.label" = ""pen_eject""
				device generic 0 on end
			end
		end
		device ref i2c3 on
			chip drivers/i2c/generic
				register "hid" = ""RTL5682""
				register "name" = ""RT58""
				register "desc" = ""Headset Codec""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_count" = "1"
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on end
			end
			chip drivers/generic/alc1015
				register "hid" = ""RTL1019""
				register "sdb" =  "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
				device generic 0 on end
			end
		end
		device ref i2c5 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
				register "wake" = "GPE0_DW2_14"
				register "probed" = "1"
				device i2c 15 on end
			end
		end
		device ref pcie_rp4 on
			# PCIe 4 WLAN
			register "pch_pcie_rp[PCH_RP(4)]" = "{
				.clk_src = 2,
				.clk_req = 2,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip drivers/wifi/generic
				register "wake" = "GPE0_DW1_03"
				device pci 00.0 on end
			end
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)"
				register "srcclk_pin" = "2"
				device generic 0 on end
			end
		end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				use conn1 as mux_conn[1]
				device pnp 0c09.0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port1 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
					chip drivers/intel/pmc_mux/conn
						use usb2_port2 as usb2_port
						use tcss_usb3_port2 as usb3_port
						device generic 1 alias conn1 on
							probe DB_USB DB_1C_1A
						end
					end
				end
			end
		end
		device ref tcss_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref tcss_usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
						device ref tcss_usb3_port2 on end
					end
				end
			end
		end
		device ref xhci on
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C1 (DB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
						device ref usb2_port2 on
							probe DB_USB DB_1C_1A
						end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A0 (MLB)""
						register "type" = "UPC_TYPE_A"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb2_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_A"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
						device ref usb2_port4 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 UFC""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 WFC""
						register "type" = "UPC_TYPE_INTERNAL"
						device ref usb2_port7 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
						device ref usb2_port8 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""CNVi Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A0 (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A1 (DB)""
						register "type" = "UPC_TYPE_USB3_A"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
						device ref usb3_port2 on end
					end
				end
			end
		end
	end
end