src/mainboard/google/myst/variants/baseboard/devicetree.cb

# SPDX-License-Identifier: GPL-2.0-or-later
chip soc/amd/phoenix

	# eSPI Configuration
	# TODO(b/276913952) bump clock back up to 33MHz once things seem to be working well.
	register "common_config.espi_config" = "{
		.std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN,
		.generic_io_range[0] = {
			.base = 0x62,
			.size = 1,
		},
		.generic_io_range[1] = {
			.base = 0x66,
			.size = 1,
		},
		.generic_io_range[2] = {
			.base = 0x800,   /* EC_HOST_CMD_REGION0 */
			.size = 256,     /* EC_HOST_CMD_REGION_SIZE * 2 */
		},
		.generic_io_range[3] = {
			.base = 0x900,   /* EC_LPC_ADDR_MEMMAP */
			.size = 255,     /* EC_MEMMAP_SIZE */
		},
		.generic_io_range[4] = {
			.base = 0x200,   /* EC_LPC_ADDR_HOST_DATA */
			.size = 8,       /* 0x200 - 0x207 */
		},

		.io_mode = ESPI_IO_MODE_QUAD,
		.op_freq_mhz = ESPI_OP_FREQ_16_MHZ,
		.crc_check_enable = 1,
		.alert_pin = ESPI_ALERT_PIN_OPEN_DRAIN,
		.periph_ch_en = 1,
		.vw_ch_en = 1,
		.oob_ch_en = 0,
		.flash_ch_en = 0,

		.vw_irq_polarity = ESPI_VW_IRQ_LEVEL_HIGH(1),
	}"

	register "i2c_scl_reset" = "GPIO_I2C0_SCL | GPIO_I2C1_SCL |
					GPIO_I2C2_SCL | GPIO_I2C3_SCL"

	# I2C Pad Control RX Select Configuration
	register "i2c_pad[0].rx_level" = "I2C_PAD_RX_1_8V" # Trackpad
	register "i2c_pad[1].rx_level" = "I2C_PAD_RX_1_8V" # Touchscreen
	register "i2c_pad[2].rx_level" = "I2C_PAD_RX_1_8V" # GSC
	register "i2c_pad[3].rx_level" = "I2C_PAD_RX_1_8V" # Speaker, Codec, P-SAR, USB

	# I2C Config
	#+-------------------+----------------------------+
	#| Field             |  Value                     |
	#+-------------------+----------------------------+
	#| I2C0              | Trackpad                   |
	#| I2C1              | Touchscreen                |
	#| I2C2              | GSC TPM                    |
	#| I2C3              | Speaker, Codec, P-SAR, USB |
	#+-------------------+----------------------------+
	register "i2c[0]" = "{
		.speed = I2C_SPEED_FAST,
	}"

	register "i2c[1]" = "{
		.speed = I2C_SPEED_FAST,
	}"

	register "i2c[2]" = "{
		.speed = I2C_SPEED_FAST,
		.early_init = true,
	}"

	register "i2c[3]" = "{
		.speed = I2C_SPEED_FAST,
	}"

	# general purpose PCIe clock output configuration
	register "gpp_clk_config[0]" = "GPP_CLK_REQ" # WLAN
	register "gpp_clk_config[1]" = "GPP_CLK_REQ" # SD
	register "gpp_clk_config[2]" = "GPP_CLK_REQ" # WWAN
	register "gpp_clk_config[3]" = "GPP_CLK_REQ" # SSD
	register "gpp_clk_config[4]" = "GPP_CLK_OFF" # SOC_FP_BOOT0 GPIO
	register "gpp_clk_config[5]" = "GPP_CLK_OFF" # WLAN_AUX_RST_L GPIO
	register "gpp_clk_config[6]" = "GPP_CLK_OFF" # WWAN_AUX_RST_L GPIO

	register "pspp_policy" = "DXIO_PSPP_DISABLED" # TODO(b/277214353): reenable when PSPP works
	register "s0ix_enable" = "true"

	register "usb_phy_custom" = "1"
	register "usb_phy" = "{
		.Usb2PhyPort[0] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[1] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[2] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[3] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[4] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[5] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[6] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb2PhyPort[7] = {
			.compdistune = 0x3,
			.pllbtune = 0x1,
			.pllitune = 0x0,
			.pllptune = 0xe,
			.sqrxtune = 0x3,
			.txfslstune = 0x3,
			.txpreempamptune = 0x2,
			.txpreemppulsetune = 0x0,
			.txrisetune = 0x1,
			.txvreftune = 0x3,
			.txhsxvtune = 0x3,
			.txrestune = 0x2,
		},
		.Usb3PhyPort[0] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.Usb3PhyPort[1] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.Usb3PhyPort[2] = {
			.tx_term_ctrl = 0x2,
			.rx_term_ctrl = 0x2,
			.tx_vboost_lvl_en = 0x0,
			.tx_vboost_lvl = 0x5,
		},
		.ComboPhyStaticConfig[0] = USB_COMBO_PHY_MODE_USB_C,
		.ComboPhyStaticConfig[1] = USB_COMBO_PHY_MODE_USB_C,
		.ComboPhyStaticConfig[2] = USB_COMBO_PHY_MODE_USB_C,
		.BatteryChargerEnable = 0,
		.PhyP3CpmP4Support = 0,
	}"

	device domain 0 on
		device ref gpp_bridge_2_1 on end # WWAN
		device ref gpp_bridge_2_2 on # WLAN
			chip drivers/wifi/generic
				register "wake" = "GEVENT_8"
				device pci 00.0 on end
			end
		end
		device ref gpp_bridge_2_3 on end # SD
		device ref gpp_bridge_2_4 on end # NVMe
		device ref gpp_bridge_a on  # Internal GPP Bridge 0 to Bus A
			device ref gfx on end # Internal GPU (GFX)
			device ref gfx_hda on end # Display HD Audio Controller (GFXAZ)
			device ref crypto on end # Crypto Coprocessor
			device ref xhci_0 on # USB 3.1 (USB0)
				chip drivers/usb/acpi
					device ref xhci_0_root_hub on
						chip drivers/usb/acpi
							register "desc" = ""USB3 Type-A Port A0 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
							device ref usb3_port2 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB3 Type-A Port A1 (DB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
							register "group" = "ACPI_PLD_GROUP(1, 2)"
							device ref usb3_port3 on
								probe DAUGHTERBOARD DB_B
							end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB3 WWAN""
							register "type" = "UPC_TYPE_INTERNAL"
							register "has_power_resource" = "1"
							register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_6)"
							register "enable_delay_ms" = "20"
							register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_11)"
							register "reset_off_delay_ms" = "20"
							device ref usb3_port3 on
								probe WWAN WWAN_FM101GL
							end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB2 Type-A Port A0 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
							device ref usb2_port2 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB2 Type-A Port A1 (DB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
							device ref usb2_port3 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""User-Facing Camera""
							register "type" = "UPC_TYPE_INTERNAL"
							device ref usb2_port4 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""World-Facing Camera""
							register "type" = "UPC_TYPE_INTERNAL"
							device ref usb2_port5 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""Bluetooth""
							register "type" = "UPC_TYPE_INTERNAL"
							register "has_power_resource" = "true"
							register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_154)"
							register "enable_delay_ms" = "500"
							register "enable_off_delay_ms" = "200"
							register "use_gpio_for_status" = "true"
							device ref usb2_port6 on end
						end
					end
				end
			end
			device ref acp on end # Audio Processor (ACP)
			device ref mp2 on end # Sensor Fusion Hub (MP2)
		end
		device ref gpp_bridge_c on  # Internal GPP Bridge 2 to Bus C
			device ref usb4_xhci_0 on
				chip drivers/usb/acpi
					register "type" = "UPC_TYPE_HUB"
					device ref usb4_xhci_0_root_hub on
						chip drivers/usb/acpi
							register "desc" = ""USB4 Type-C Port C0 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
							device ref usb3_port0 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB4 Type-C Port C0 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
							device ref usb2_port0 on end
						end
					end
				end
			end
			device ref usb4_xhci_1 on
				chip drivers/usb/acpi
					register "type" = "UPC_TYPE_HUB"
					device ref usb4_xhci_1_root_hub on
						chip drivers/usb/acpi
							register "desc" = ""USB4 Type-C Port C1 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(4, 1))"
							device ref usb3_port1 on end
						end
						chip drivers/usb/acpi
							register "desc" = ""USB2 Type-C Port C1 (MLB)""
							register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
							register "use_custom_pld" = "true"
							register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(4, 1))"
							device ref usb2_port1 on end
						end
					end
				end
			end
		end
		device ref iommu on end
		device ref lpc_bridge on
			chip ec/google/chromeec
				device pnp 0c09.0 alias chrome_ec on end
			end
		end
	end # domain
	device ref uart_0 on end # UART0
	device ref i2c_0 on end
	device ref i2c_1 on end
	device ref i2c_2 on
		chip drivers/i2c/tpm
			register "hid" = ""GOOG0005""
			register "desc" = ""Ti50 TPM""
			register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_84)"
			device i2c 50 alias ti50 on end
		end
	end
	device ref i2c_3 on end
end	# chip soc/amd/phoenix