| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2012 Advanced Micro Devices, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| |
| #include <arch/io.h> |
| #include <arch/romcc_io.h> |
| |
| |
| #if CONFIG_CONSOLE_POST == 1 |
| |
| /* Data */ |
| #define UART_RBR 0x00 |
| #define UART_TBR 0x00 |
| |
| /* Control */ |
| #define UART_IER 0x01 |
| #define UART_IIR 0x02 |
| #define UART_FCR 0x02 |
| #define UART_LCR 0x03 |
| #define UART_MCR 0x04 |
| #define UART_DLL 0x00 |
| #define UART_DLM 0x01 |
| |
| /* Status */ |
| #define UART_LSR 0x05 |
| #define UART_MSR 0x06 |
| #define UART_SCR 0x07 |
| |
| #ifndef CONFIG_TTYS0_DIV |
| #if ((115200%CONFIG_TTYS0_BAUD) != 0) |
| #error Bad ttys0 baud rate |
| #endif |
| #define CONFIG_TTYS0_DIV (115200/CONFIG_TTYS0_BAUD) |
| #endif // CONFIG_TTYS0_DIV |
| |
| #define UART_LCS CONFIG_TTYS0_LCS |
| |
| #endif // CONFIG_CONSOLE_POST == 1 |
| |
| |
| static void sb700_enable_rom(void) |
| { |
| u32 word; |
| u32 dword; |
| device_t dev; |
| |
| dev = PCI_DEV(0, 0x14, 0x03); |
| /* SB700 LPC Bridge 0:20:3:44h. |
| * BIT6: Port Enable for serial port 0x3f8-0x3ff |
| * BIT29: Port Enable for KBC port 0x60 and 0x64 |
| * BIT30: Port Enable for ACPI Micro-Controller port 0x66 and 0x62 |
| */ |
| dword = pci_io_read_config32(dev, 0x44); |
| //dword |= (1<<6) | (1<<29) | (1<<30) ; |
| /*Turn on all of LPC IO Port decode enable */ |
| dword = 0xffffffff; |
| pci_io_write_config32(dev, 0x44, dword); |
| |
| /* SB700 LPC Bridge 0:20:3:48h. |
| * BIT0: Port Enable for SuperIO 0x2E-0x2F |
| * BIT1: Port Enable for SuperIO 0x4E-0x4F |
| * BIT4: Port Enable for LPC ROM Address Arrage2 (0x68-0x6C) |
| * BIT6: Port Enable for RTC IO 0x70-0x73 |
| * BIT21: Port Enable for Port 0x80 |
| */ |
| dword = pci_io_read_config32(dev, 0x48); |
| dword |= (1<<0) | (1<<1) | (1<<4) | (1<<6) | (1<<21) ; |
| pci_io_write_config32(dev, 0x48, dword); |
| |
| /* Enable 4MB rom access at 0xFFE00000 - 0xFFFFFFFF */ |
| /* Set the 4MB enable bits */ |
| word = pci_io_read_config16(dev, 0x6c); |
| word = 0xFFC0; |
| pci_io_write_config16(dev, 0x6c, word); |
| } |
| |
| static void bootblock_southbridge_init(void) |
| { |
| /* Setup the rom access for 2M */ |
| sb700_enable_rom(); |
| } |