| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2003 Eric Biederman |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #ifndef UART8250_H |
| #define UART8250_H |
| |
| #if CONFIG_CONSOLE_SERIAL8250 || CONFIG_CONSOLE_SERIAL8250MEM |
| |
| /* Data */ |
| #define UART_RBR 0x00 |
| #define UART_TBR 0x00 |
| |
| /* Control */ |
| #define UART_IER 0x01 |
| #define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ |
| #define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ |
| #define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ |
| #define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ |
| |
| #define UART_IIR 0x02 |
| #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ |
| #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ |
| |
| #define UART_IIR_MSI 0x00 /* Modem status interrupt */ |
| #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ |
| #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ |
| #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ |
| |
| #define UART_FCR 0x02 |
| #define UART_FCR_FIFO_EN 0x01 /* Fifo enable */ |
| #define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ |
| #define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ |
| #define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ |
| #define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ |
| #define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ |
| #define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ |
| #define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ |
| #define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ |
| |
| #define UART_FCR_RXSR 0x02 /* Receiver soft reset */ |
| #define UART_FCR_TXSR 0x04 /* Transmitter soft reset */ |
| |
| #define UART_LCR 0x03 |
| #define UART_LCR_WLS_MSK 0x03 /* character length select mask */ |
| #define UART_LCR_WLS_5 0x00 /* 5 bit character length */ |
| #define UART_LCR_WLS_6 0x01 /* 6 bit character length */ |
| #define UART_LCR_WLS_7 0x02 /* 7 bit character length */ |
| #define UART_LCR_WLS_8 0x03 /* 8 bit character length */ |
| #define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */ |
| #define UART_LCR_PEN 0x08 /* Parity eneble */ |
| #define UART_LCR_EPS 0x10 /* Even Parity Select */ |
| #define UART_LCR_STKP 0x20 /* Stick Parity */ |
| #define UART_LCR_SBRK 0x40 /* Set Break */ |
| #define UART_LCR_BKSE 0x80 /* Bank select enable */ |
| #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ |
| |
| #define UART_MCR 0x04 |
| #define UART_MCR_DTR 0x01 /* DTR */ |
| #define UART_MCR_RTS 0x02 /* RTS */ |
| #define UART_MCR_OUT1 0x04 /* Out 1 */ |
| #define UART_MCR_OUT2 0x08 /* Out 2 */ |
| #define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ |
| |
| #define UART_MCR_DMA_EN 0x04 |
| #define UART_MCR_TX_DFR 0x08 |
| |
| #define UART_DLL 0x00 |
| #define UART_DLM 0x01 |
| |
| /* Status */ |
| #define UART_LSR 0x05 |
| #define UART_LSR_DR 0x01 /* Data ready */ |
| #define UART_LSR_OE 0x02 /* Overrun */ |
| #define UART_LSR_PE 0x04 /* Parity error */ |
| #define UART_LSR_FE 0x08 /* Framing error */ |
| #define UART_LSR_BI 0x10 /* Break */ |
| #define UART_LSR_THRE 0x20 /* Xmit holding register empty */ |
| #define UART_LSR_TEMT 0x40 /* Xmitter empty */ |
| #define UART_LSR_ERR 0x80 /* Error */ |
| |
| #define UART_MSR 0x06 |
| #define UART_MSR_DCD 0x80 /* Data Carrier Detect */ |
| #define UART_MSR_RI 0x40 /* Ring Indicator */ |
| #define UART_MSR_DSR 0x20 /* Data Set Ready */ |
| #define UART_MSR_CTS 0x10 /* Clear to Send */ |
| #define UART_MSR_DDCD 0x08 /* Delta DCD */ |
| #define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ |
| #define UART_MSR_DDSR 0x02 /* Delta DSR */ |
| #define UART_MSR_DCTS 0x01 /* Delta CTS */ |
| |
| #define UART_SCR 0x07 |
| #define UART_SPR 0x07 |
| |
| #if ((115200 % CONFIG_TTYS0_BAUD) != 0) |
| #error Bad ttyS0 baud rate |
| #endif |
| |
| /* Line Control Settings */ |
| #define UART_LCS CONFIG_TTYS0_LCS |
| |
| #ifndef __ROMCC__ |
| #if CONFIG_CONSOLE_SERIAL8250 |
| unsigned char uart8250_rx_byte(unsigned base_port); |
| int uart8250_can_rx_byte(unsigned base_port); |
| void uart8250_tx_byte(unsigned base_port, unsigned char data); |
| void uart8250_tx_flush(unsigned base_port); |
| /* Yes it is silly to have three different uart init functions. But we used to |
| * have three different sets of uart code, so it's an improvement. |
| */ |
| void uart8250_init(unsigned base_port, unsigned divisor); |
| void uart_init(void); |
| #endif |
| #if CONFIG_CONSOLE_SERIAL8250MEM |
| void uartmem_init(void); |
| |
| /* and the same for memory mapped uarts */ |
| unsigned char uart8250_mem_rx_byte(unsigned base_port); |
| int uart8250_mem_can_rx_byte(unsigned base_port); |
| void uart8250_mem_tx_byte(unsigned base_port, unsigned char data); |
| void uart8250_mem_tx_flush(unsigned base_port); |
| void uart8250_mem_init(unsigned base_port, unsigned divisor); |
| u32 uart_mem_init(void); |
| |
| #if defined(__PRE_RAM__) && CONFIG_DRIVERS_OXFORD_OXPCIE |
| /* and special init for OXPCIe based cards */ |
| extern int oxford_oxpcie_present; |
| |
| void oxford_init(void); |
| #endif |
| #endif |
| |
| #endif /* __ROMCC__ */ |
| |
| #endif /* CONFIG_CONSOLE_SERIAL8250 || CONFIG_CONSOLE_SERIAL8250MEM */ |
| |
| #endif /* UART8250_H */ |