| /* |
| * Copyright (c) 2012 The Linux Foundation. All rights reserved.* |
| * |
| * Copyright (c) 2010, Code Aurora Forum. All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are |
| * met: |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above |
| * copyright notice, this list of conditions and the following |
| * disclaimer in the documentation and/or other materials provided |
| * with the distribution. |
| * * Neither the name of Code Aurora Forum, Inc. nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS |
| * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
| * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
| * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR |
| * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, |
| * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE |
| * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN |
| * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| #ifndef __UART_DM_H__ |
| #define __UART_DM_H__ |
| |
| #define PERIPH_BLK_BLSP 0 |
| |
| #define MSM_BOOT_UART_DM_EXTR_BITS(value, start_pos, end_pos) \ |
| ((value << (32 - end_pos))\ |
| >> (32 - (end_pos - start_pos))) |
| |
| extern void __udelay(unsigned long usec); |
| |
| |
| enum MSM_BOOT_UART_DM_PARITY_MODE { |
| MSM_BOOT_UART_DM_NO_PARITY, |
| MSM_BOOT_UART_DM_ODD_PARITY, |
| MSM_BOOT_UART_DM_EVEN_PARITY, |
| MSM_BOOT_UART_DM_SPACE_PARITY |
| }; |
| |
| /* UART Stop Bit Length */ |
| enum MSM_BOOT_UART_DM_STOP_BIT_LEN { |
| MSM_BOOT_UART_DM_SBL_9_16, |
| MSM_BOOT_UART_DM_SBL_1, |
| MSM_BOOT_UART_DM_SBL_1_9_16, |
| MSM_BOOT_UART_DM_SBL_2 |
| }; |
| |
| /* UART Bits per Char */ |
| enum MSM_BOOT_UART_DM_BITS_PER_CHAR { |
| MSM_BOOT_UART_DM_5_BPS, |
| MSM_BOOT_UART_DM_6_BPS, |
| MSM_BOOT_UART_DM_7_BPS, |
| MSM_BOOT_UART_DM_8_BPS |
| }; |
| |
| /* 8-N-1 Configuration */ |
| #define MSM_BOOT_UART_DM_8_N_1_MODE (MSM_BOOT_UART_DM_NO_PARITY | \ |
| (MSM_BOOT_UART_DM_SBL_1 << 2) | \ |
| (MSM_BOOT_UART_DM_8_BPS << 4)) |
| |
| /* UART_DM Registers */ |
| |
| /* UART Operational Mode Register */ |
| #define MSM_BOOT_UART_DM_MR1(base) ((base) + 0x00) |
| #define MSM_BOOT_UART_DM_MR2(base) ((base) + 0x04) |
| #define MSM_BOOT_UART_DM_RXBRK_ZERO_CHAR_OFF (1 << 8) |
| #define MSM_BOOT_UART_DM_LOOPBACK (1 << 7) |
| |
| /* UART Clock Selection Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_CSR(base) ((base) + 0xA0) |
| #else |
| #define MSM_BOOT_UART_DM_CSR(base) ((base) + 0x08) |
| #endif |
| |
| /* UART DM TX FIFO Registers - 4 */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x100+(4*(x))) |
| #else |
| #define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x70+(4*(x))) |
| #endif |
| |
| /* UART Command Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_CR(base) ((base) + 0xA8) |
| #else |
| #define MSM_BOOT_UART_DM_CR(base) ((base) + 0x10) |
| #endif |
| #define MSM_BOOT_UART_DM_CR_RX_ENABLE (1 << 0) |
| #define MSM_BOOT_UART_DM_CR_RX_DISABLE (1 << 1) |
| #define MSM_BOOT_UART_DM_CR_TX_ENABLE (1 << 2) |
| #define MSM_BOOT_UART_DM_CR_TX_DISABLE (1 << 3) |
| |
| /* UART Channel Command */ |
| #define MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x) ((x & 0x0f) << 4) |
| #define MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x) ((x >> 4 ) << 11 ) |
| #define MSM_BOOT_UART_DM_CR_CH_CMD(x) (MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x)\ |
| | MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x)) |
| #define MSM_BOOT_UART_DM_CMD_NULL MSM_BOOT_UART_DM_CR_CH_CMD(0) |
| #define MSM_BOOT_UART_DM_CMD_RESET_RX MSM_BOOT_UART_DM_CR_CH_CMD(1) |
| #define MSM_BOOT_UART_DM_CMD_RESET_TX MSM_BOOT_UART_DM_CR_CH_CMD(2) |
| #define MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT MSM_BOOT_UART_DM_CR_CH_CMD(3) |
| #define MSM_BOOT_UART_DM_CMD_RES_BRK_CHG_INT MSM_BOOT_UART_DM_CR_CH_CMD(4) |
| #define MSM_BOOT_UART_DM_CMD_START_BRK MSM_BOOT_UART_DM_CR_CH_CMD(5) |
| #define MSM_BOOT_UART_DM_CMD_STOP_BRK MSM_BOOT_UART_DM_CR_CH_CMD(6) |
| #define MSM_BOOT_UART_DM_CMD_RES_CTS_N MSM_BOOT_UART_DM_CR_CH_CMD(7) |
| #define MSM_BOOT_UART_DM_CMD_RES_STALE_INT MSM_BOOT_UART_DM_CR_CH_CMD(8) |
| #define MSM_BOOT_UART_DM_CMD_PACKET_MODE MSM_BOOT_UART_DM_CR_CH_CMD(9) |
| #define MSM_BOOT_UART_DM_CMD_MODE_RESET MSM_BOOT_UART_DM_CR_CH_CMD(C) |
| #define MSM_BOOT_UART_DM_CMD_SET_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(D) |
| #define MSM_BOOT_UART_DM_CMD_RES_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(E) |
| #define MSM_BOOT_UART_DM_CMD_RES_TX_ERR MSM_BOOT_UART_DM_CR_CH_CMD(10) |
| #define MSM_BOOT_UART_DM_CMD_CLR_TX_DONE MSM_BOOT_UART_DM_CR_CH_CMD(11) |
| #define MSM_BOOT_UART_DM_CMD_RES_BRKSTRT_INT MSM_BOOT_UART_DM_CR_CH_CMD(12) |
| #define MSM_BOOT_UART_DM_CMD_RES_BRKEND_INT MSM_BOOT_UART_DM_CR_CH_CMD(13) |
| #define MSM_BOOT_UART_DM_CMD_RES_PER_FRM_INT MSM_BOOT_UART_DM_CR_CH_CMD(14) |
| |
| /*UART General Command */ |
| #define MSM_BOOT_UART_DM_CR_GENERAL_CMD(x) ((x) << 8) |
| |
| #define MSM_BOOT_UART_DM_GCMD_NULL MSM_BOOT_UART_DM_CR_GENERAL_CMD(0) |
| #define MSM_BOOT_UART_DM_GCMD_CR_PROT_EN MSM_BOOT_UART_DM_CR_GENERAL_CMD(1) |
| #define MSM_BOOT_UART_DM_GCMD_CR_PROT_DIS MSM_BOOT_UART_DM_CR_GENERAL_CMD(2) |
| #define MSM_BOOT_UART_DM_GCMD_RES_TX_RDY_INT MSM_BOOT_UART_DM_CR_GENERAL_CMD(3) |
| #define MSM_BOOT_UART_DM_GCMD_SW_FORCE_STALE MSM_BOOT_UART_DM_CR_GENERAL_CMD(4) |
| #define MSM_BOOT_UART_DM_GCMD_ENA_STALE_EVT MSM_BOOT_UART_DM_CR_GENERAL_CMD(5) |
| #define MSM_BOOT_UART_DM_GCMD_DIS_STALE_EVT MSM_BOOT_UART_DM_CR_GENERAL_CMD(6) |
| |
| /* UART Interrupt Mask Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_IMR(base) ((base) + 0xB0) |
| #else |
| #define MSM_BOOT_UART_DM_IMR(base) ((base) + 0x14) |
| #endif |
| |
| #define MSM_BOOT_UART_DM_TXLEV (1 << 0) |
| #define MSM_BOOT_UART_DM_RXHUNT (1 << 1) |
| #define MSM_BOOT_UART_DM_RXBRK_CHNG (1 << 2) |
| #define MSM_BOOT_UART_DM_RXSTALE (1 << 3) |
| #define MSM_BOOT_UART_DM_RXLEV (1 << 4) |
| #define MSM_BOOT_UART_DM_DELTA_CTS (1 << 5) |
| #define MSM_BOOT_UART_DM_CURRENT_CTS (1 << 6) |
| #define MSM_BOOT_UART_DM_TX_READY (1 << 7) |
| #define MSM_BOOT_UART_DM_TX_ERROR (1 << 8) |
| #define MSM_BOOT_UART_DM_TX_DONE (1 << 9) |
| #define MSM_BOOT_UART_DM_RXBREAK_START (1 << 10) |
| #define MSM_BOOT_UART_DM_RXBREAK_END (1 << 11) |
| #define MSM_BOOT_UART_DM_PAR_FRAME_ERR_IRQ (1 << 12) |
| |
| #define MSM_BOOT_UART_DM_IMR_ENABLED (MSM_BOOT_UART_DM_TX_READY | \ |
| MSM_BOOT_UART_DM_TXLEV | \ |
| MSM_BOOT_UART_DM_RXSTALE) |
| |
| /* UART Interrupt Programming Register */ |
| #define MSM_BOOT_UART_DM_IPR(base) ((base) + 0x18) |
| #define MSM_BOOT_UART_DM_STALE_TIMEOUT_LSB 0x0f |
| #define MSM_BOOT_UART_DM_STALE_TIMEOUT_MSB 0 /* Not used currently */ |
| |
| /* UART Transmit/Receive FIFO Watermark Register */ |
| #define MSM_BOOT_UART_DM_TFWR(base) ((base) + 0x1C) |
| /* Interrupt is generated when FIFO level is less than or equal to this value */ |
| #define MSM_BOOT_UART_DM_TFW_VALUE 0 |
| |
| #define MSM_BOOT_UART_DM_RFWR(base) ((base) + 0x20) |
| /*Interrupt generated when no of words in RX FIFO is greater than this value */ |
| #define MSM_BOOT_UART_DM_RFW_VALUE 0 |
| |
| /* UART Hunt Character Register */ |
| #define MSM_BOOT_UART_DM_HCR(base) ((base) + 0x24) |
| |
| /* Used for RX transfer initialization */ |
| #define MSM_BOOT_UART_DM_DMRX(base) ((base) + 0x34) |
| |
| /* Default DMRX value - any value bigger than FIFO size would be fine */ |
| #define MSM_BOOT_UART_DM_DMRX_DEF_VALUE 0x220 |
| |
| /* Register to enable IRDA function */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0xB8) |
| #else |
| #define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0x38) |
| #endif |
| |
| /* UART Data Mover Enable Register */ |
| #define MSM_BOOT_UART_DM_DMEN(base) ((base) + 0x3C) |
| |
| /* Number of characters for Transmission */ |
| #define MSM_BOOT_UART_DM_NO_CHARS_FOR_TX(base) ((base) + 0x040) |
| |
| /* UART RX FIFO Base Address */ |
| #define MSM_BOOT_UART_DM_BADR(base) ((base) + 0x44) |
| |
| /* UART Status Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_SR(base) ((base) + 0x0A4) |
| #else |
| #define MSM_BOOT_UART_DM_SR(base) ((base) + 0x008) |
| #endif |
| #define MSM_BOOT_UART_DM_SR_RXRDY (1 << 0) |
| #define MSM_BOOT_UART_DM_SR_RXFULL (1 << 1) |
| #define MSM_BOOT_UART_DM_SR_TXRDY (1 << 2) |
| #define MSM_BOOT_UART_DM_SR_TXEMT (1 << 3) |
| #define MSM_BOOT_UART_DM_SR_UART_OVERRUN (1 << 4) |
| #define MSM_BOOT_UART_DM_SR_PAR_FRAME_ERR (1 << 5) |
| #define MSM_BOOT_UART_DM_RX_BREAK (1 << 6) |
| #define MSM_BOOT_UART_DM_HUNT_CHAR (1 << 7) |
| #define MSM_BOOT_UART_DM_RX_BRK_START_LAST (1 << 8) |
| |
| /* UART Receive FIFO Registers - 4 in numbers */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x140 + (4*(x))) |
| #else |
| #define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x70 + (4*(x))) |
| #endif |
| |
| /* UART Masked Interrupt Status Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_MISR(base) ((base) + 0xAC) |
| #else |
| #define MSM_BOOT_UART_DM_MISR(base) ((base) + 0x10) |
| #endif |
| |
| /* UART Interrupt Status Register */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_ISR(base) ((base) + 0xB4) |
| #else |
| #define MSM_BOOT_UART_DM_ISR(base) ((base) + 0x14) |
| #endif |
| |
| /* Number of characters received since the end of last RX transfer */ |
| #if PERIPH_BLK_BLSP |
| #define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0xBC) |
| #else |
| #define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0x38) |
| #endif |
| |
| /* UART TX FIFO Status Register */ |
| #define MSM_BOOT_UART_DM_TXFS(base) ((base) + 0x4C) |
| #define MSM_BOOT_UART_DM_TXFS_STATE_LSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x,0,6) |
| #define MSM_BOOT_UART_DM_TXFS_STATE_MSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x,14,31) |
| #define MSM_BOOT_UART_DM_TXFS_BUF_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x,7,9) |
| #define MSM_BOOT_UART_DM_TXFS_ASYNC_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x,10,13) |
| |
| /* UART RX FIFO Status Register */ |
| #define MSM_BOOT_UART_DM_RXFS(base) ((base) + 0x50) |
| #define MSM_BOOT_UART_DM_RXFS_STATE_LSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x,0,6) |
| #define MSM_BOOT_UART_DM_RXFS_STATE_MSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x,14,31) |
| #define MSM_BOOT_UART_DM_RXFS_BUF_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x,7,9) |
| #define MSM_BOOT_UART_DM_RXFS_ASYNC_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x,10,13) |
| |
| /* Macros for Common Errors */ |
| #define MSM_BOOT_UART_DM_E_SUCCESS 0 |
| #define MSM_BOOT_UART_DM_E_FAILURE 1 |
| #define MSM_BOOT_UART_DM_E_TIMEOUT 2 |
| #define MSM_BOOT_UART_DM_E_INVAL 3 |
| #define MSM_BOOT_UART_DM_E_MALLOC_FAIL 4 |
| #define MSM_BOOT_UART_DM_E_RX_NOT_READY 5 |
| |
| #endif /* __UART_DM_H__ */ |
| |