| chip soc/intel/jasperlake |
| |
| # USB Port Configuration |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # User Facing Camera |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | Digitizer | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | Camera | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| device domain 0 on |
| device pci 05.0 on # IPU - MIPI Camera |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "2" |
| register "cio2_lanes_used" = "{1,4}" |
| register "cio2_lane_endpoint[1]" = ""^I2C3.CAM1"" |
| register "cio2_prt[0]" = "0" |
| register "cio2_prt[1]" = "2" |
| device generic 0 on end |
| end |
| end |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""User Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D15)" |
| register "enable_delay_ms" = "20" |
| device usb 2.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end #I2C 0 |
| device pci 15.2 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "7" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end # I2C 2 |
| device pci 15.3 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM1"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "4" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "360000000" |
| register "link_freq[1]" = "180000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D13" #power_enable_2p8 |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D14" #power_enable_1p2 |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D12" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C3.CAM1.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0c on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "nvm_size" = "0x0400" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x08" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on end |
| end |
| end # I2C 3 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "0" |
| device i2c 28 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on end |
| end |
| end # I2C 4 |
| device pci 1f.3 on end # Intel HDA |
| end |
| end |