| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| |
| #ifndef _SOC_BLOCK_GPIO_DEFS_H_ |
| #define _SOC_BLOCK_GPIO_DEFS_H_ |
| |
| #define PAD_CFG0_TX_STATE_BIT 0 |
| #define PAD_CFG0_TX_STATE (1 << PAD_CFG0_TX_STATE_BIT) |
| #define PAD_CFG0_RX_STATE_BIT 1 |
| #define PAD_CFG0_RX_STATE (1 << PAD_CFG0_RX_STATE_BIT) |
| #define PAD_CFG0_TX_DISABLE (1 << 8) |
| #define PAD_CFG0_RX_DISABLE (1 << 9) |
| #define PAD_CFG0_MODE_SHIFT 10 |
| #define PAD_CFG0_MODE_MASK (7 << 10) |
| #define PAD_CFG0_MODE_GPIO (0 << 10) |
| #define PAD_CFG0_MODE_FUNC(x) ((x) << 10) |
| #define PAD_CFG0_MODE_NF1 (1 << 10) |
| #define PAD_CFG0_MODE_NF2 (2 << 10) |
| #define PAD_CFG0_MODE_NF3 (3 << 10) |
| #define PAD_CFG0_MODE_NF4 (4 << 10) |
| #define PAD_CFG0_MODE_NF5 (5 << 10) |
| #define PAD_CFG0_MODE_NF6 (6 << 10) |
| #define PAD_CFG0_MODE_NF7 (7 << 10) |
| #define PAD_CFG0_ROUTE_MASK (0xF << 17) |
| #define PAD_CFG0_ROUTE_NMI (1 << 17) |
| #define PAD_CFG0_ROUTE_SMI (1 << 18) |
| #define PAD_CFG0_ROUTE_SCI (1 << 19) |
| #define PAD_CFG0_ROUTE_IOAPIC (1 << 20) |
| #define PAD_CFG0_RXTENCFG_MASK (3 << 21) |
| #define PAD_CFG0_RXINV_MASK (1 << 23) |
| #define PAD_CFG0_RX_POL_INVERT (1 << 23) |
| #define PAD_CFG0_RX_POL_NONE (0 << 23) |
| #define PAD_CFG0_PREGFRXSEL (1 << 24) |
| #define PAD_CFG0_TRIG_MASK (3 << 25) |
| #define PAD_CFG0_TRIG_LEVEL (0 << 25) |
| #define PAD_CFG0_TRIG_EDGE_SINGLE (1 << 25) /* controlled by RX_INVERT*/ |
| #define PAD_CFG0_TRIG_OFF (2 << 25) |
| #define PAD_CFG0_TRIG_EDGE_BOTH (3 << 25) |
| #define PAD_CFG0_RXRAW1_MASK (1 << 28) |
| #define PAD_CFG0_RXPADSTSEL_MASK (1 << 29) |
| #define PAD_CFG0_RESET_MASK (3 << 30) |
| #define PAD_CFG0_LOGICAL_RESET_PWROK (0U << 30) |
| #define PAD_CFG0_LOGICAL_RESET_DEEP (1U << 30) |
| #define PAD_CFG0_LOGICAL_RESET_PLTRST (2U << 30) |
| #define PAD_CFG0_LOGICAL_RESET_RSMRST (3U << 30) |
| |
| /* |
| * Use the fourth bit in IntSel field to indicate gpio |
| * ownership. This field is RO and hence not used during |
| * gpio configuration. |
| */ |
| #define PAD_CFG_OWN_GPIO_DRIVER (1 << 4) |
| #define PAD_CFG_OWN_GPIO_ACPI (0 << 4) |
| #define PAD_CFG_OWN_GPIO(own) PAD_CFG_OWN_GPIO_##own |
| |
| #define PAD_CFG1_IRQ_MASK (0xff << 0) |
| #define PAD_CFG1_IOSTERM_MASK (0x3 << 8) |
| #define PAD_CFG1_IOSTERM_SAME (0x0 << 8) |
| #define PAD_CFG1_IOSTERM_DISPUPD (0x1 << 8) |
| #define PAD_CFG1_IOSTERM_ENPD (0x2 << 8) |
| #define PAD_CFG1_IOSTERM_ENPU (0x3 << 8) |
| #define PAD_CFG1_PULL_MASK (0xf << 10) |
| #define PAD_CFG1_PULL_NONE (0x0 << 10) |
| #define PAD_CFG1_PULL_DN_5K (0x2 << 10) |
| #define PAD_CFG1_PULL_DN_20K (0x4 << 10) |
| #define PAD_CFG1_PULL_UP_1K (0x9 << 10) |
| #define PAD_CFG1_PULL_UP_5K (0xa << 10) |
| #define PAD_CFG1_PULL_UP_2K (0xb << 10) |
| #define PAD_CFG1_PULL_UP_20K (0xc << 10) |
| #define PAD_CFG1_PULL_UP_667 (0xd << 10) |
| #define PAD_CFG1_PULL_NATIVE (0xf << 10) |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_IOSTANDBY) |
| /* Tx enabled driving last value driven, Rx enabled */ |
| #define PAD_CFG1_IOSSTATE_TxLASTRxE (0x0 << 14) |
| /* Tx enabled driving 0, Rx disabled and Rx driving 0 back to its controller |
| * internally */ |
| #define PAD_CFG1_IOSSTATE_Tx0RxDCRx0 (0x1 << 14) |
| /* Tx enabled driving 0, Rx disabled and Rx driving 1 back to its controller |
| * internally */ |
| #define PAD_CFG1_IOSSTATE_Tx0RxDCRx1 (0x2 << 14) |
| /* Tx enabled driving 1, Rx disabled and Rx driving 0 back to its controller |
| * internally */ |
| #define PAD_CFG1_IOSSTATE_Tx1RxDCRx0 (0x3 << 14) |
| /* Tx enabled driving 1, Rx disabled and Rx driving 1 back to its controller |
| * internally */ |
| #define PAD_CFG1_IOSSTATE_Tx1RxDCRx1 (0x4 << 14) |
| /* Tx enabled driving 0, Rx enabled */ |
| #define PAD_CFG1_IOSSTATE_Tx0RxE (0x5 << 14) |
| /* Tx enabled driving 1, Rx enabled */ |
| #define PAD_CFG1_IOSSTATE_Tx1RxE (0x6 << 14) |
| /* Hi-Z, Rx driving 0 back to its controller internally */ |
| #define PAD_CFG1_IOSSTATE_HIZCRx0 (0x7 << 14) |
| /* Hi-Z, Rx driving 1 back to its controller internally */ |
| #define PAD_CFG1_IOSSTATE_HIZCRx1 (0x8 << 14) |
| #define PAD_CFG1_IOSSTATE_TxDRxE (0x9 << 14) /* Tx disabled, Rx enabled */ |
| #define PAD_CFG1_IOSSTATE_IGNORE (0xf << 14) /* Ignore Iostandby */ |
| #define PAD_CFG1_IOSSTATE_MASK (0xf << 14) /* mask to extract Iostandby bits */ |
| #define PAD_CFG1_IOSSTATE_SHIFT 14 /* set Iostandby bits [17:14] */ |
| #else /* CONFIG_SOC_INTEL_COMMON_BLOCK_GPIO_IOSTANDBY */ |
| #define PAD_CFG1_IOSSTATE_MASK 0 |
| #endif /* CONFIG_SOC_INTEL_COMMON_BLOCK_GPIO_IOSTANDBY */ |
| |
| #define PAD_CFG2_DEBEN 1 |
| /* Debounce Duration = (2 ^ PAD_CFG2_DEBOUNCE_x_RTC) * RTC clock duration */ |
| #define PAD_CFG2_DEBOUNCE_8_RTC (0x3 << 1) |
| #define PAD_CFG2_DEBOUNCE_16_RTC (0x4 << 1) |
| #define PAD_CFG2_DEBOUNCE_32_RTC (0x5 << 1) |
| #define PAD_CFG2_DEBOUNCE_64_RTC (0x6 << 1) |
| #define PAD_CFG2_DEBOUNCE_128_RTC (0x7 << 1) |
| #define PAD_CFG2_DEBOUNCE_256_RTC (0x8 << 1) |
| #define PAD_CFG2_DEBOUNCE_512_RTC (0x9 << 1) |
| #define PAD_CFG2_DEBOUNCE_1K_RTC (0xa << 1) |
| #define PAD_CFG2_DEBOUNCE_2K_RTC (0xb << 1) |
| #define PAD_CFG2_DEBOUNCE_4K_RTC (0xc << 1) |
| #define PAD_CFG2_DEBOUNCE_8K_RTC (0xd << 1) |
| #define PAD_CFG2_DEBOUNCE_16K_RTC (0xe << 1) |
| #define PAD_CFG2_DEBOUNCE_32K_RTC (0xf << 1) |
| #define PAD_CFG2_DEBOUNCE_MASK 0x1f |
| |
| /* voltage tolerance 0=3.3V default 1=1.8V tolerant */ |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_PADCFG_PADTOL) |
| #define PAD_CFG1_TOL_MASK (0x1 << 25) |
| #define PAD_CFG1_TOL_1V8 (0x1 << 25) |
| #endif /* CONFIG_SOC_INTEL_COMMON_BLOCK_GPIO_PADCFG_PADTOL */ |
| |
| #define PAD_FUNC(value) PAD_CFG0_MODE_##value |
| #define PAD_RESET(value) PAD_CFG0_LOGICAL_RESET_##value |
| #define PAD_RX_POL(value) PAD_CFG0_RX_POL_##value |
| #define PAD_IRQ_ROUTE(value) PAD_CFG0_ROUTE_##value |
| #define PAD_TRIG(value) PAD_CFG0_TRIG_##value |
| #define PAD_PULL(value) PAD_CFG1_PULL_##value |
| |
| /* Disable the input/output buffer of the pad */ |
| #define PAD_CFG0_BUF_NO_DISABLE (0) |
| #define PAD_CFG0_BUF_TX_DISABLE PAD_CFG0_TX_DISABLE |
| #define PAD_CFG0_BUF_RX_DISABLE PAD_CFG0_RX_DISABLE |
| #define PAD_CFG0_BUF_TX_RX_DISABLE \ |
| (PAD_CFG0_TX_DISABLE | PAD_CFG0_RX_DISABLE) |
| |
| #define PAD_BUF(value) PAD_CFG0_BUF_##value |
| |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_IOSTANDBY) |
| #define PAD_IOSSTATE(value) PAD_CFG1_IOSSTATE_##value |
| #define PAD_IOSTERM(value) PAD_CFG1_IOSTERM_##value |
| #else |
| #define PAD_IOSSTATE(value) 0 |
| #define PAD_IOSTERM(value) 0 |
| #endif |
| |
| #define PAD_IRQ_CFG(route, trig, inv) \ |
| (PAD_IRQ_ROUTE(route) | \ |
| PAD_TRIG(trig) | \ |
| PAD_RX_POL(inv)) |
| |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT) |
| #define PAD_IRQ_CFG_DUAL_ROUTE(route1, route2, trig, inv) \ |
| (PAD_IRQ_ROUTE(route1) | \ |
| PAD_IRQ_ROUTE(route2) | \ |
| PAD_TRIG(trig) | \ |
| PAD_RX_POL(inv)) |
| #endif /* CONFIG_SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT */ |
| |
| #define _PAD_CFG_STRUCT(__pad, __config0, __config1) \ |
| { \ |
| .pad = __pad, \ |
| .pad_config[0] = __config0, \ |
| .pad_config[1] = __config1, \ |
| } |
| |
| #if GPIO_NUM_PAD_CFG_REGS > 2 |
| #define _PAD_CFG_STRUCT_3(__pad, __config0, __config1, __config2) \ |
| { \ |
| .pad = __pad, \ |
| .pad_config[0] = __config0, \ |
| .pad_config[1] = __config1, \ |
| .pad_config[2] = __config2, \ |
| } |
| #else |
| #define _PAD_CFG_STRUCT_3(__pad, __config0, __config1, __config2) \ |
| _PAD_CFG_STRUCT(__pad, __config0, __config1) |
| #endif |
| |
| /* Native function configuration */ |
| #define PAD_CFG_NF(pad, pull, rst, func) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_RESET(rst) | PAD_FUNC(func), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxLASTRxE)) |
| |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_PADCFG_PADTOL) |
| /* Native 1.8V tolerant pad, only applies to some pads like I2C/I2S |
| Not applicable to all SOCs. Refer EDS |
| */ |
| #define PAD_CFG_NF_1V8(pad, pull, rst, func) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_RESET(rst) | PAD_FUNC(func), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxLASTRxE) | PAD_CFG1_TOL_1V8) |
| #endif |
| |
| /* Native function configuration for standby state */ |
| #define PAD_CFG_NF_IOSSTATE(pad, pull, rst, func, iosstate) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_RESET(rst) | PAD_FUNC(func), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(iosstate)) |
| |
| /* Native function configuration for standby state, also configuring |
| iostandby as masked */ |
| #define PAD_CFG_NF_IOSTANDBY_IGNORE(pad, pull, rst, func) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_RESET(rst) | PAD_FUNC(func), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(IGNORE)) |
| |
| /* Native function configuration for standby state, also configuring |
| iosstate and iosterm */ |
| #define PAD_CFG_NF_IOSSTATE_IOSTERM(pad, pull, rst, func, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_RESET(rst) | PAD_FUNC(func), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| /* General purpose output, no pullup/down. */ |
| #define PAD_CFG_GPO(pad, val, rst) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | \ |
| PAD_TRIG(OFF) | PAD_BUF(RX_DISABLE) | !!val, \ |
| PAD_PULL(NONE) | PAD_IOSSTATE(TxLASTRxE)) |
| |
| /* General purpose output, with termination specified */ |
| #define PAD_CFG_TERM_GPO(pad, val, pull, rst) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | \ |
| PAD_TRIG(OFF) | PAD_BUF(RX_DISABLE) | !!val, \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxLASTRxE)) |
| |
| /* General purpose output, no pullup/down. */ |
| #define PAD_CFG_GPO_GPIO_DRIVER(pad, val, rst, pull) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | \ |
| PAD_TRIG(OFF) | PAD_BUF(RX_DISABLE) | !!val, \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxLASTRxE) | \ |
| PAD_CFG_OWN_GPIO(DRIVER)) |
| |
| /* General purpose output. */ |
| #define PAD_CFG_GPO_IOSSTATE_IOSTERM(pad, val, rst, pull, iosstate, ioterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | \ |
| PAD_TRIG(OFF) | PAD_BUF(RX_DISABLE) | !!val, \ |
| PAD_PULL(pull) | PAD_IOSSTATE(iosstate) | PAD_IOSTERM(ioterm)) |
| |
| /* General purpose input */ |
| #define PAD_CFG_GPI(pad, pull, rst) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxDRxE)) |
| |
| #define PAD_CFG_GPI_TRIG_IOSSTATE_OWN(pad, pull, rst, trig, iosstate, own) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_TRIG(trig) | PAD_BUF(TX_DISABLE), \ |
| PAD_PULL(pull) | PAD_CFG_OWN_GPIO(own) | PAD_IOSSTATE(iosstate)) |
| |
| #define PAD_CFG_GPI_TRIG_IOS_OWN(pad, pull, rst, trig, iosstate, iosterm, own) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_TRIG(trig) | PAD_BUF(TX_DISABLE), \ |
| PAD_PULL(pull) | PAD_CFG_OWN_GPIO(own) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| /* |
| * General purpose input. The following macro sets the |
| * Host Software Pad Ownership to GPIO Driver mode. |
| */ |
| #define PAD_CFG_GPI_TRIG_OWN(pad, pull, rst, trig, own) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | \ |
| PAD_TRIG(trig) | PAD_RX_POL(NONE) | PAD_BUF(TX_DISABLE), \ |
| PAD_PULL(pull) | PAD_CFG_OWN_GPIO(own)) |
| |
| #define PAD_CFG_GPI_GPIO_DRIVER(pad, pull, rst) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE), \ |
| PAD_PULL(pull) | PAD_CFG_OWN_GPIO(DRIVER) | PAD_IOSSTATE(TxDRxE)) |
| |
| #define PAD_CFG_GPIO_DRIVER_HI_Z(pad, pull, rst, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_RX_DISABLE), \ |
| PAD_PULL(pull) | PAD_CFG_OWN_GPIO(DRIVER) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| #define PAD_CFG_GPIO_HI_Z(pad, pull, rst, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_RX_DISABLE), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| /* GPIO Interrupt */ |
| #define PAD_CFG_GPI_INT(pad, pull, rst, trig) \ |
| PAD_CFG_GPI_TRIG_OWN(pad, pull, rst, trig, DRIVER) |
| |
| /* |
| * No Connect configuration for unused pad. |
| * Both TX and RX are disabled. RX disabling is done to avoid unnecessary |
| * setting of GPI_STS. RX Level/Edge Trig Configuration set to disable |
| */ |
| #define PAD_NC(pad, pull) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(DEEP) | \ |
| PAD_TRIG(OFF) | PAD_BUF(TX_RX_DISABLE), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxDRxE)) |
| |
| /* General purpose input, routed to APIC */ |
| #define PAD_CFG_GPI_APIC(pad, pull, rst, trig, inv) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(IOAPIC, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(TxDRxE)) |
| |
| /* General purpose input, routed to APIC - with IOStandby Config*/ |
| #define PAD_CFG_GPI_APIC_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(IOAPIC, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| /* |
| * The following APIC macros assume the APIC will handle the filtering |
| * on its own end. One just needs to pass an active high message into the |
| * ITSS. |
| */ |
| #define PAD_CFG_GPI_APIC_LOW(pad, pull, rst) \ |
| PAD_CFG_GPI_APIC(pad, pull, rst, LEVEL, INVERT) |
| |
| #define PAD_CFG_GPI_APIC_HIGH(pad, pull, rst) \ |
| PAD_CFG_GPI_APIC(pad, pull, rst, LEVEL, NONE) |
| |
| #define PAD_CFG_GPI_APIC_EDGE_LOW(pad, pull, rst) \ |
| PAD_CFG_GPI_APIC(pad, pull, rst, EDGE_SINGLE, INVERT) |
| |
| /* General purpose input, routed to SMI */ |
| #define PAD_CFG_GPI_SMI(pad, pull, rst, trig, inv) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(SMI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(TxDRxE)) |
| |
| /* General purpose input, routed to SMI */ |
| #define PAD_CFG_GPI_SMI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(SMI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| #define PAD_CFG_GPI_SMI_LOW(pad, pull, rst, trig) \ |
| PAD_CFG_GPI_SMI(pad, pull, rst, trig, INVERT) |
| |
| #define PAD_CFG_GPI_SMI_HIGH(pad, pull, rst, trig) \ |
| PAD_CFG_GPI_SMI(pad, pull, rst, trig, NONE) |
| |
| /* General purpose input, routed to SCI */ |
| #define PAD_CFG_GPI_SCI(pad, pull, rst, trig, inv) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(TxDRxE)) |
| |
| /* General purpose input, routed to SCI */ |
| #define PAD_CFG_GPI_SCI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(iosstate) | PAD_IOSTERM(iosterm)) |
| |
| #define PAD_CFG_GPI_SCI_LOW(pad, pull, rst, trig) \ |
| PAD_CFG_GPI_SCI(pad, pull, rst, trig, INVERT) |
| |
| #define PAD_CFG_GPI_SCI_HIGH(pad, pull, rst, trig) \ |
| PAD_CFG_GPI_SCI(pad, pull, rst, trig, NONE) |
| |
| #define PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, inv, dur) \ |
| _PAD_CFG_STRUCT_3(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(TxDRxE), PAD_CFG2_DEBEN | PAD_CFG2_##dur) |
| |
| #define PAD_CFG_GPI_SCI_LOW_DEBEN(pad, pull, rst, trig, dur) \ |
| PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, INVERT, dur) |
| |
| #define PAD_CFG_GPI_SCI_HIGH_DEBEN(pad, pull, rst, trig, dur) \ |
| PAD_CFG_GPI_SCI_DEBEN(pad, pull, rst, trig, NONE, dur) |
| |
| /* General purpose input, routed to NMI */ |
| #define PAD_CFG_GPI_NMI(pad, pull, rst, trig, inv) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG(NMI, trig, inv), PAD_PULL(pull) | \ |
| PAD_IOSSTATE(TxDRxE)) |
| |
| #if CONFIG(SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT) |
| #define PAD_CFG_GPI_DUAL_ROUTE(pad, pull, rst, trig, inv, route1, route2) \ |
| _PAD_CFG_STRUCT(pad, \ |
| PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_BUF(TX_DISABLE) | \ |
| PAD_IRQ_CFG_DUAL_ROUTE(route1, route2, trig, inv), \ |
| PAD_PULL(pull) | PAD_IOSSTATE(TxDRxE)) |
| |
| #define PAD_CFG_GPI_IRQ_WAKE(pad, pull, rst, trig, inv) \ |
| PAD_CFG_GPI_DUAL_ROUTE(pad, pull, rst, trig, inv, IOAPIC, SCI) |
| |
| #endif /* CONFIG_SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT */ |
| |
| #endif /* _SOC_BLOCK_GPIO_DEFS_H_ */ |