| fw_config |
| field USBC0_RETIMER 2 3 |
| option USBC0_RETIMER_ABSENT 0 |
| option USBC0_RETIMER_PRESENT 1 |
| end |
| field STORAGE 4 5 |
| option STORAGE_UNKNOWN 0 |
| option STORAGE_NVME 1 |
| option STORAGE_EMMC 2 |
| end |
| field AUDIO 6 |
| option AUDIO_UNKNOWN 0 |
| option NAU88L25B_I2S 1 |
| end |
| end |
| chip soc/intel/alderlake |
| # As per Intel Advisory doc#723158, the change is required to prevent possible |
| # display flickering issue. |
| register "usb2_phy_sus_pg_disable" = "1" |
| # Enable HDMI2 in PortA, HDMI1 in PortB, HDMI/DP in Port2 |
| register "ddi_ports_config" = "{ |
| [DDI_PORT_A] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| [DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| [DDI_PORT_1] = DDI_ENABLE_HPD, |
| [DDI_PORT_2] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| [DDI_PORT_3] = DDI_ENABLE_HPD, |
| }" |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2 Port2 |
| register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC2)" # USB2 Port3 |
| register "usb2_ports[3]" = "USB2_PORT_SHORT(OC_SKIP)" # Enable USB2 Port4 |
| register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Disable USB2 Port9 |
| register "usb3_ports[2]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_de_emp = 0x2B, |
| .tx_downscale_amp = 0x00, |
| }" # Type-A port A2 |
| register "tcss_ports[3]" = "TCSS_PORT_EMPTY" # Disable TCP3 |
| |
| # Bitmap for Wake Enable on USB attach/detach |
| register "usb2_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(4) | |
| USB_PORT_WAKE_ENABLE(6) | |
| USB_PORT_WAKE_ENABLE(7) | |
| USB_PORT_WAKE_ENABLE(8)" |
| register "usb3_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(1) | |
| USB_PORT_WAKE_ENABLE(2) | |
| USB_PORT_WAKE_ENABLE(3) | |
| USB_PORT_WAKE_ENABLE(4)" |
| |
| register "tcc_offset" = "0" # TCC of 100C |
| register "power_limits_config[ADL_P_142_242_282_15W_CORE]" = "{ |
| .tdp_pl1_override = 55, |
| }" |
| register "power_limits_config[ADL_P_282_442_482_28W_CORE]" = "{ |
| .tdp_pl1_override = 64, |
| }" |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""SSD"" |
| register "options.tsr[1].desc" = ""CPU_VR"" |
| register "options.tsr[2].desc" = ""DIMM"" |
| |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 15000, |
| .max_power = 55000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 55000, |
| .max_power = 55000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| register "oem_data.oem_variables" = "{ |
| [0] = 0x1 |
| }" |
| |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port1 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port3 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end # USB4 Port |
| device ref pcie4_0 on |
| # Enable CPU PCIE RP 1 using CLK 0 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 0, |
| .clk_src = 0, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| probe STORAGE STORAGE_NVME |
| probe STORAGE STORAGE_UNKNOWN |
| end # SSD |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end # WiFi |
| device ref i2c0 on |
| chip drivers/i2c/nau8825 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" |
| register "jkdet_enable" = "1" |
| register "jkdet_pull_enable" = "0" |
| register "jkdet_pull_up" = "0" |
| register "jkdet_polarity" = "1" # ActiveLow |
| register "vref_impedance" = "2" # 125kOhm |
| register "micbias_voltage" = "6" # 2.754 |
| register "sar_threshold_num" = "4" |
| register "sar_threshold[0]" = "0x0C" |
| register "sar_threshold[1]" = "0x1C" |
| register "sar_threshold[2]" = "0x38" |
| register "sar_threshold[3]" = "0x60" |
| register "sar_hysteresis" = "1" |
| register "sar_voltage" = "6" |
| register "sar_compare_time" = "0" # 500ns |
| register "sar_sampling_time" = "0" # 2us |
| register "short_key_debounce" = "2" # 100ms |
| register "jack_insert_debounce" = "7" # 512ms |
| register "jack_eject_debounce" = "7" # 512ms |
| device i2c 1a on end |
| end |
| end # Audio Nau8825 |
| device ref pcie_rp6 on |
| # Enable PCIe-to-i225 bridge PCIe 6 using clk 4 |
| register "pch_pcie_rp[PCH_RP(6)]" = "{ |
| .clk_src = 4, |
| .clk_req = 4, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| device generic 0 on end |
| end # IntelI225V Ethernet NIC |
| device ref pcie_rp7 on |
| chip drivers/net |
| register "customized_leds" = "0x0482" |
| register "wake" = "GPE0_DW0_07" |
| register "device_index" = "0" |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end # RTL8111K Ethernet NIC |
| device ref pcie_rp8 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end # SD card |
| device ref pcie_rp9 off end #pcie_rp 9 Empty |
| device ref pcie_rp10 off end #pcie_rp 10 Empty |
| device ref pcie_rp11 off end #pcie_rp 11 Empty |
| device ref pcie_rp12 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E20)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B3)" |
| register "srcclk_pin" = "1" |
| register "reset_delay_ms" = "50" |
| register "enable_delay_ms" = "20" |
| device generic 0 alias emmc_rtd3 on |
| probe STORAGE STORAGE_EMMC |
| probe STORAGE STORAGE_UNKNOWN |
| end |
| end # Enable PCIe-to-eMMC bridge PCIE 12 using clk 1 |
| register "pch_pcie_rp[PCH_RP(12)]" = "{ |
| .clk_src = 1, |
| .clk_req = 1, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| probe STORAGE STORAGE_EMMC |
| probe STORAGE STORAGE_UNKNOWN |
| end # BH799BB |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(FRONT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A4 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 NFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A3 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(5, 1))" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A2 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(6, 1))" |
| device ref usb2_port7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(7, 1))" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(7, 2))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A2 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(6, 1))" |
| device ref usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A3 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(5, 1))" |
| device ref usb3_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A4 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end # USB2 and USB3 Port |
| end |
| |
| end |