| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| |
| #ifndef _SOC_APOLLOLAKE_CHIP_H_ |
| #define _SOC_APOLLOLAKE_CHIP_H_ |
| |
| #include <commonlib/helpers.h> |
| #include <drivers/intel/gma/gma.h> |
| #include <intelblocks/cfg.h> |
| #include <intelblocks/gspi.h> |
| #include <gpio.h> |
| #include <soc/gpe.h> |
| #include <intelblocks/lpc_lib.h> |
| #include <intelblocks/power_limit.h> |
| #include <device/i2c_simple.h> |
| #include <drivers/i2c/designware/dw_i2c.h> |
| #include <soc/pm.h> |
| #include <soc/usb.h> |
| |
| #define MAX_PCIE_PORTS 6 |
| #define CLKREQ_DISABLED 0xf |
| |
| enum pnp_settings { |
| PNP_PERF, |
| PNP_POWER, |
| PNP_PERF_POWER, |
| }; |
| |
| enum sata_speed_limit { |
| SATA_DEFAULT = 0, |
| SATA_GEN1, |
| SATA_GEN2, |
| SATA_GEN3 |
| }; |
| |
| struct soc_intel_apollolake_config { |
| |
| /* Common structure containing soc config data required by common code*/ |
| struct soc_intel_common_config common_soc_config; |
| |
| /* Common struct containing power limits configuration info */ |
| struct soc_power_limits_config power_limits_config; |
| |
| /* |
| * IGD panel configuration |
| * |
| * Second backlight control shares logic with other pins (aka. display utility pin). |
| * Be sure it's used for PWM before setting any secondary backlight value. |
| */ |
| struct i915_gpu_panel_config panel_cfg[2]; |
| |
| /* i915 struct for GMA backlight control */ |
| struct i915_gpu_controller_info gfx; |
| |
| /* |
| * Mapping from PCIe root port to CLKREQ input on the SOC. The SOC has |
| * four CLKREQ inputs, but six root ports. Root ports without an |
| * associated CLKREQ signal must be marked with "CLKREQ_DISABLED" |
| */ |
| uint8_t pcie_rp_clkreq_pin[MAX_PCIE_PORTS]; |
| |
| /* Enable/disable hot-plug for root ports (0 = disable, 1 = enable). */ |
| uint8_t pcie_rp_hotplug_enable[MAX_PCIE_PORTS]; |
| |
| /* De-emphasis enable configuration for each PCIe root port */ |
| uint8_t pcie_rp_deemphasis_enable[MAX_PCIE_PORTS]; |
| |
| /* [14:8] DDR mode Number of dealy elements.Each = 125pSec. |
| * [6:0] SDR mode Number of dealy elements.Each = 125pSec. |
| */ |
| uint32_t emmc_tx_cmd_cntl; |
| |
| /* [14:8] HS400 mode Number of dealy elements.Each = 125pSec. |
| * [6:0] SDR104/HS200 mode Number of dealy elements.Each = 125pSec. |
| */ |
| uint32_t emmc_tx_data_cntl1; |
| |
| /* [30:24] SDR50 mode Number of dealy elements.Each = 125pSec. |
| * [22:16] DDR50 mode Number of dealy elements.Each = 125pSec. |
| * [14:8] SDR25/HS50 mode Number of dealy elements.Each = 125pSec. |
| * [6:0] SDR12/Compatibility mode Number of dealy elements. |
| * Each = 125pSec. |
| */ |
| uint32_t emmc_tx_data_cntl2; |
| |
| /* [30:24] SDR50 mode Number of dealy elements.Each = 125pSec. |
| * [22:16] DDR50 mode Number of dealy elements.Each = 125pSec. |
| * [14:8] SDR25/HS50 mode Number of dealy elements.Each = 125pSec. |
| * [6:0] SDR12/Compatibility mode Number of dealy elements. |
| * Each = 125pSec. |
| */ |
| uint32_t emmc_rx_cmd_data_cntl1; |
| |
| /* [14:8] HS400 mode 1 Number of dealy elements.Each = 125pSec. |
| * [6:0] HS400 mode 2 Number of dealy elements.Each = 125pSec. |
| */ |
| uint32_t emmc_rx_strobe_cntl; |
| |
| /* [13:8] Auto Tuning mode Number of dealy elements.Each = 125pSec. |
| * [6:0] SDR104/HS200 Number of dealy elements.Each = 125pSec. |
| */ |
| uint32_t emmc_rx_cmd_data_cntl2; |
| |
| /* Select the eMMC max speed allowed. */ |
| uint8_t emmc_host_max_speed; |
| |
| /* Sata Ports Hot Plug */ |
| uint8_t SataPortsHotPlug[2]; |
| |
| /* Sata Ports Enable */ |
| uint8_t SataPortsEnable[2]; |
| |
| /* Specifies on which IRQ the SCI will internally appear. */ |
| uint8_t sci_irq; |
| |
| /* Configure serial IRQ (SERIRQ) line. */ |
| enum serirq_mode serirq_mode; |
| |
| uint8_t gpe0_dw1; /* GPE0_63_32 STS/EN */ |
| uint8_t gpe0_dw2; /* GPE0_95_64 STS/EN */ |
| uint8_t gpe0_dw3; /* GPE0_127_96 STS/EN */ |
| |
| /* LPC fixed enables and ranges */ |
| uint16_t lpc_iod; |
| uint16_t lpc_ioe; |
| |
| /* Generic IO decode ranges */ |
| uint32_t gen1_dec; |
| uint32_t gen2_dec; |
| uint32_t gen3_dec; |
| uint32_t gen4_dec; |
| |
| /* Configure LPSS S0ix Enable */ |
| uint8_t lpss_s0ix_enable; |
| |
| /* Enable DPTF support */ |
| int dptf_enable; |
| |
| /* TCC activation offset value in degrees Celsius */ |
| uint32_t tcc_offset; |
| |
| /* Configure Audio clk gate and power gate |
| * IOSF-SB port ID 92 offset 0x530 [5] and [3] |
| */ |
| uint8_t hdaudio_clk_gate_enable; |
| uint8_t hdaudio_pwr_gate_enable; |
| uint8_t hdaudio_bios_config_lockdown; |
| |
| /* Enhanced C-states */ |
| int enhanced_cstates; |
| |
| /* SLP S3 minimum assertion width. */ |
| int slp_s3_assertion_width_usecs; |
| |
| /* GPIO pin for PERST_0 */ |
| uint16_t prt0_gpio; |
| |
| /* USB2 eye diagram settings per port */ |
| struct usb2_eye_per_port usb2eye[APOLLOLAKE_USB2_PORT_MAX]; |
| |
| /* Override USB port configuration */ |
| uint8_t usb_config_override; |
| struct usb_port_config usb2_port[APOLLOLAKE_USB2_PORT_MAX]; |
| struct usb_port_config usb3_port[APOLLOLAKE_USB3_PORT_MAX]; |
| |
| /* GPIO SD card detect pin */ |
| unsigned int sdcard_cd_gpio; |
| |
| /* Select PNP Settings. |
| * (0) Performance, |
| * (1) Power |
| * (2) Power & Performance */ |
| enum pnp_settings pnp_settings; |
| |
| /* PMIC PCH_PWROK delay configuration - IPC Configuration |
| * Upd for changing PCH_PWROK delay configuration : I2C_Slave_Address |
| * (31:24) + Register_Offset (23:16) + OR Value (15:8) + AND Value (7:0) |
| */ |
| uint32_t PmicPmcIpcCtrl; |
| |
| /* Options to disable XHCI Link Compliance Mode. Default is FALSE to not |
| * disable Compliance Mode. Set TRUE to disable Compliance Mode. |
| * 0:FALSE(Default), 1:True. |
| */ |
| uint8_t DisableComplianceMode; |
| |
| /* Options to change USB3 ModPhy setting for the Integrated Filter (IF) |
| * value. Default is 0 to not changing default IF value (0x12). Set |
| * value with the range from 0x01 to 0xff to change IF value. |
| */ |
| uint8_t ModPhyIfValue; |
| |
| /* Options to bump USB3 LDO voltage. Default is FALSE to not increasing |
| * LDO voltage. Set TRUE to increase LDO voltage with 40mV. |
| * 0:FALSE (default), 1:True. |
| */ |
| uint8_t ModPhyVoltageBump; |
| |
| /* Options to adjust PMIC Vdd2 voltage. Default is 0 to not adjusting |
| * the PMIC Vdd2 default voltage 1.20v. Upd for changing Vdd2 Voltage |
| * configuration: I2C_Slave_Address (31:23) + Register_Offset (23:16) |
| * + OR Value (15:8) + AND Value (7:0) through BUCK5_VID[3:2]: |
| * 00=1.10v, 01=1.15v, 10=1.24v, 11=1.20v (default). |
| */ |
| uint32_t PmicVdd2Voltage; |
| |
| /* Option to enable VTD feature. Default is 0 which disables VTD |
| * capability in FSP. Setting this option to 1 in devicetree will enable |
| * the Upd parameter VtdEnable. |
| */ |
| uint8_t enable_vtd; |
| |
| /* Options to disable the LFPS periodic sampling for USB3 Ports. |
| * Default value of PMCTRL_REG bits[7:4] is 9 which means periodic sampling |
| * interval is 9ms. |
| * Set 1 to update XHCI host MMIO BAR + PMCTRL_REG (0x80A4 bits[7:4]) to 0 |
| * 0:Enable (default), 1:Disable. |
| */ |
| uint8_t disable_xhci_lfps_pm; |
| |
| /* SATA Aggressive Link Power Management */ |
| uint8_t DisableSataSalpSupport; |
| |
| /* Sata Power Optimisation */ |
| uint8_t SataPwrOptimizeDisable; |
| |
| /* SATA speed limit */ |
| enum sata_speed_limit sata_speed; |
| }; |
| |
| typedef struct soc_intel_apollolake_config config_t; |
| |
| #endif /* _SOC_APOLLOLAKE_CHIP_H_ */ |