| chip soc/intel/alderlake |
| |
| register "usb2_ports[2]" = "USB2_PORT_EMPTY" |
| register "usb2_ports[3]" = "USB2_PORT_EMPTY" |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # UFCamera |
| |
| register "usb3_ports[2]" = "USB3_PORT_EMPTY" |
| register "usb3_ports[3]" = "USB3_PORT_EMPTY" |
| |
| register "tcss_ports[2]" = "TCSS_PORT_EMPTY" |
| |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| }" |
| |
| register "serial_io_gspi_mode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| }" |
| |
| # Enable eDP in Port A |
| register "ddi_portA_config" = "1" |
| |
| register "ddi_ports_config" = "{ |
| [DDI_PORT_A] = DDI_ENABLE_HPD, |
| [DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, |
| }" |
| |
| register "sagv" = "SaGv_Enabled" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C3 | TouchScreen | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 600, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 600, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| }" |
| |
| device domain 0 on |
| device ref pcie4_0 on |
| # Enable CPU PCIE RP 1 using CLK 0 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 0, |
| .clk_src = 0, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, CENTER, ACPI_PLD_GROUP(1, 1))" |
| register "usb_lpm_incapable" = "true" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(FRONT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| register "usb_lpm_incapable" = "true" |
| device ref tcss_usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, CENTER, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(FRONT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""UFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A17)" |
| register "enable_delay_ms" = "20" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A3 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(5, 1))" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A2 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(6, 1))" |
| device ref usb2_port7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/nau8825 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" |
| register "jkdet_enable" = "1" |
| register "jkdet_pull_enable" = "0" |
| register "jkdet_pull_up" = "0" |
| register "jkdet_polarity" = "1" # ActiveLow |
| register "vref_impedance" = "2" # 125kOhm |
| register "micbias_voltage" = "6" # 2.754 |
| register "sar_threshold_num" = "4" |
| register "sar_threshold[0]" = "0x0C" |
| register "sar_threshold[1]" = "0x1C" |
| register "sar_threshold[2]" = "0x38" |
| register "sar_threshold[3]" = "0x60" |
| register "sar_hysteresis" = "1" |
| register "sar_voltage" = "6" |
| register "sar_compare_time" = "0" # 500ns |
| register "sar_sampling_time" = "0" # 2us |
| register "short_key_debounce" = "2" # 100ms |
| register "jack_insert_debounce" = "7" # 512ms |
| register "jack_eject_debounce" = "7" # 512ms |
| device i2c 1a on end |
| end # Audio Nau8825 |
| end # I2C0 |
| device ref i2c3 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""LM230001"" |
| register "generic.desc" = ""LM238 Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C6)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.has_power_resource" = "1" |
| device i2c 34 on end |
| end |
| end # I2C3 |
| device ref pcie_rp5 on |
| # Enable PCIE 5 using clk 2 |
| register "pch_pcie_rp[PCH_RP(5)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" |
| register "srcclk_pin" = "2" |
| device generic 0 on end |
| end |
| end #PCIE5 WLAN |
| device ref pcie_rp7 on |
| # Enable PCIE 7 using clk 6 |
| register "pch_pcie_rp[PCH_RP(7)]" = "{ |
| .clk_src = 6, |
| .clk_req = 6, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/net |
| register "customized_leds" = "0x0843" |
| register "wake" = "GPE0_DW0_07" #GPP_A7 |
| register "device_index" = "0" |
| device generic 0 on end |
| end |
| end #PCIE7 RTL8111K Ethernet NIC |
| device ref pcie_rp8 off end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/alc1015 |
| register "hid" = ""RTL1015"" |
| device generic 0 on end |
| end # RT1015 Amplifier |
| end # Intel HDA |
| end |
| end |