| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #ifndef __PICASSO_CHIP_H__ |
| #define __PICASSO_CHIP_H__ |
| |
| #include <stddef.h> |
| #include <stdint.h> |
| #include <amdblocks/chip.h> |
| #include <commonlib/helpers.h> |
| #include <drivers/i2c/designware/dw_i2c.h> |
| #include <soc/i2c.h> |
| #include <soc/iomap.h> |
| #include <soc/southbridge.h> |
| #include <acpi/acpi_device.h> |
| |
| struct soc_amd_picasso_config { |
| struct soc_amd_common_config common_config; |
| /* |
| * If sb_reset_i2c_slaves() is called, this devicetree register |
| * defines which I2C SCL will be toggled 9 times at 100 KHz. |
| * For example, should we need I2C0 and I2C3 have their slave |
| * devices reseted by toggling SCL, use: |
| * |
| * register i2c_scl_reset = (GPIO_I2C0_SCL | GPIO_I2C3_SCL) |
| */ |
| u8 i2c_scl_reset; |
| struct dw_i2c_bus_config i2c[I2C_MASTER_DEV_COUNT]; |
| enum { |
| I2S_PINS_MAX_HDA = 0, /* HDA w/reset 3xSDI, SW w/Data0 */ |
| I2S_PINS_MAX_MHDA = 1, /* HDA no reset 3xSDI, SW w/Data0-1 */ |
| I2S_PINS_MIN_HDA = 2, /* HDA w/reset 1xSDI, SW w/Data0-2 */ |
| I2S_PINS_MIN_MHDA = 3, /* HDA no reset 1xSDI, SW w/Data0-3 */ |
| I2S_PINS_I2S_TDM = 4, |
| I2S_PINS_UNCONF = 7, /* All pads will be input mode */ |
| } acp_pin_cfg; |
| |
| /* Options for these are in src/arch/x86/include/acpi/acpi.h */ |
| uint8_t fadt_pm_profile; |
| uint16_t fadt_boot_arch; |
| uint32_t fadt_flags; |
| |
| /* System config index */ |
| uint8_t system_config; |
| |
| /* STAPM Configuration */ |
| uint32_t fast_ppt_limit; |
| uint32_t slow_ppt_limit; |
| uint32_t slow_ppt_time_constant; |
| uint32_t stapm_time_constant; |
| uint32_t sustained_power_limit; |
| |
| /* PROCHOT_L de-assertion Ramp Time */ |
| uint32_t prochot_l_deassertion_ramp_time; |
| |
| /* Lower die temperature limit */ |
| uint32_t thermctl_limit; |
| |
| /* FP5 Processor Voltage Supply PSI Currents. 0 indicates use SOC default */ |
| uint32_t psi0_current_limit; |
| uint32_t psi0_soc_current_limit; |
| uint32_t vddcr_soc_voltage_margin; |
| uint32_t vddcr_vdd_voltage_margin; |
| |
| /* VRM Limits. 0 indicates use SOC default */ |
| uint32_t vrm_maximum_current_limit; |
| uint32_t vrm_soc_maximum_current_limit; |
| uint32_t vrm_current_limit; |
| uint32_t vrm_soc_current_limit; |
| |
| /* Misc SMU settings */ |
| uint8_t sb_tsi_alert_comparator_mode_en; |
| uint8_t core_dldo_bypass; |
| uint8_t min_soc_vid_offset; |
| uint8_t aclk_dpm0_freq_400MHz; |
| uint32_t telemetry_vddcr_vdd_slope; |
| uint32_t telemetry_vddcr_vdd_offset; |
| uint32_t telemetry_vddcr_soc_slope; |
| uint32_t telemetry_vddcr_soc_offset; |
| |
| enum { |
| SD_EMMC_DISABLE, |
| SD_EMMC_SD_LOW_SPEED, |
| SD_EMMC_SD_HIGH_SPEED, |
| SD_EMMC_SD_UHS_I_SDR_50, |
| SD_EMMC_SD_UHS_I_DDR_50, |
| SD_EMMC_SD_UHS_I_SDR_104, |
| SD_EMMC_EMMC_SDR_26, |
| SD_EMMC_EMMC_SDR_52, |
| SD_EMMC_EMMC_DDR_52, |
| SD_EMMC_EMMC_HS200, |
| SD_EMMC_EMMC_HS400, |
| SD_EMMC_EMMC_HS300, |
| } sd_emmc_config; |
| }; |
| |
| typedef struct soc_amd_picasso_config config_t; |
| |
| extern struct device_operations pci_domain_ops; |
| |
| #endif /* __PICASSO_CHIP_H__ */ |