| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2009 coresystems GmbH |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, |
| * MA 02110-1301 USA |
| */ |
| |
| #include <types.h> |
| #include <device/device.h> |
| #include <console/console.h> |
| #include <boot/tables.h> |
| #include <x86emu/x86emu.h> |
| #include <pc80/mc146818rtc.h> |
| #include <arch/io.h> |
| #include <arch/coreboot_tables.h> |
| #include "chip.h" |
| |
| int add_mainboard_resources(struct lb_memory *mem) |
| { |
| return add_northbridge_resources(mem); |
| } |
| |
| #if CONFIG_PCI_OPTION_ROM_RUN_YABEL |
| static int int15_handler(void) |
| { |
| #define BOOT_DISPLAY_DEFAULT 0 |
| #define BOOT_DISPLAY_CRT (1 << 0) |
| #define BOOT_DISPLAY_TV (1 << 1) |
| #define BOOT_DISPLAY_EFP (1 << 2) |
| #define BOOT_DISPLAY_LCD (1 << 3) |
| #define BOOT_DISPLAY_CRT2 (1 << 4) |
| #define BOOT_DISPLAY_TV2 (1 << 5) |
| #define BOOT_DISPLAY_EFP2 (1 << 6) |
| #define BOOT_DISPLAY_LCD2 (1 << 7) |
| |
| printk_debug("%s: AX=%04x BX=%04x CX=%04x DX=%04x\n", |
| __func__, M.x86.R_AX, M.x86.R_BX, M.x86.R_CX, M.x86.R_DX); |
| |
| switch (M.x86.R_AX) { |
| case 0x5f35: /* Boot Display */ |
| M.x86.R_AX = 0x005f; // Success |
| M.x86.R_CL = BOOT_DISPLAY_DEFAULT; |
| break; |
| case 0x5f40: /* Boot Panel Type */ |
| // M.x86.R_AX = 0x015f; // Supported but failed |
| M.x86.R_AX = 0x005f; // Success |
| M.x86.R_CL = 3; // Display ID |
| break; |
| default: |
| /* Interrupt was not handled */ |
| return 0; |
| } |
| |
| /* Interrupt handled */ |
| return 1; |
| } |
| |
| static void int15_install(void) |
| { |
| typedef int (* yabel_handleIntFunc)(void); |
| extern yabel_handleIntFunc yabel_intFuncArray[256]; |
| yabel_intFuncArray[0x15] = int15_handler; |
| } |
| #endif |
| |
| /* Hardware Monitor */ |
| |
| static u16 hwm_base = 0xa00; |
| |
| static void hwm_write(u8 reg, u8 value) |
| { |
| outb(reg, hwm_base + 0x05); |
| outb(value, hwm_base + 0x06); |
| } |
| |
| static void hwm_bank(u8 bank) |
| { |
| hwm_write(0x4e, bank); |
| } |
| |
| #define FAN_CRUISE_CONTROL_DISABLED 0 |
| #define FAN_CRUISE_CONTROL_SPEED 1 |
| #define FAN_CRUISE_CONTROL_THERMAL 2 |
| |
| #define FAN_SPEED_5625 0 |
| //#define FAN_TEMPERATURE_30DEGC 0 |
| |
| struct fan_speed { |
| u8 fan_in; |
| u16 fan_speed; |
| }; |
| |
| // FANIN Target Speed Register |
| // FANIN = 337500 / RPM |
| struct fan_speed fan_speeds[] = { |
| { 0x3c, 5625 }, { 0x41, 5192 }, { 0x47, 4753 }, { 0x4e, 4326 }, |
| { 0x56, 3924 }, { 0x5f, 3552 }, { 0x69, 3214 }, { 0x74, 2909 }, |
| { 0x80, 2636 }, { 0x8d, 2393 }, { 0x9b, 2177 }, { 0xaa, 1985 }, |
| { 0xba, 1814 }, { 0xcb, 1662 }, { 0xdd, 1527 }, { 0xf0, 1406 } |
| }; |
| |
| struct temperature { |
| u8 deg_celsius; |
| u8 deg_fahrenheit; |
| }; |
| |
| struct temperature temperatures[] = { |
| { 30, 86 }, { 33, 91 }, { 36, 96 }, { 39, 102 }, |
| { 42, 107 }, { 45, 113 }, { 48, 118 }, { 51, 123 }, |
| { 54, 129 }, { 57, 134 }, { 60, 140 }, { 63, 145 }, |
| { 66, 150 }, { 69, 156 }, { 72, 161 }, { 75, 167 } |
| }; |
| |
| static void hwm_setup(void) |
| { |
| int cpufan_control = 0, sysfan_control = 0; |
| int cpufan_speed = 0, sysfan_speed = 0; |
| int cpufan_temperature = 0, sysfan_temperature = 0; |
| |
| if (get_option(&cpufan_control, "cpufan_cruise_control") < 0) |
| cpufan_control = FAN_CRUISE_CONTROL_DISABLED; |
| if (get_option(&cpufan_speed, "cpufan_speed") < 0) |
| cpufan_speed = FAN_SPEED_5625; |
| //if (get_option(&cpufan_temperature, "cpufan_temperature") < 0) |
| // cpufan_temperature = FAN_TEMPERATURE_30DEGC; |
| |
| if (get_option(&sysfan_control, "sysfan_cruise_control") < 0) |
| sysfan_control = FAN_CRUISE_CONTROL_DISABLED; |
| if (get_option(&sysfan_speed, "sysfan_speed") < 0) |
| sysfan_speed = FAN_SPEED_5625; |
| //if (get_option(&sysfan_temperature, "sysfan_temperature") < 0) |
| // sysfan_temperature = FAN_TEMPERATURE_30DEGC; |
| |
| // hwm_write(0x31, 0x20); // AVCC high limit |
| // hwm_write(0x34, 0x06); // VIN2 low limit |
| |
| hwm_bank(0); |
| hwm_write(0x59, 0x20); // Diode Selection |
| hwm_write(0x5d, 0x0f); // All Sensors Diode, not Thermistor |
| |
| hwm_bank(4); |
| hwm_write(0x54, 0xf1); // SYSTIN temperature offset |
| hwm_write(0x55, 0x19); // CPUTIN temperature offset |
| hwm_write(0x56, 0xfc); // AUXTIN temperature offset |
| |
| hwm_bank(0x80); // Default |
| |
| u8 fan_config = 0; |
| // 00 FANOUT is Manual Mode |
| // 01 FANOUT is Thermal Cruise Mode |
| // 10 FANOUT is Fan Speed Cruise Mode |
| switch (cpufan_control) { |
| case FAN_CRUISE_CONTROL_SPEED: fan_config |= (2 << 4); break; |
| case FAN_CRUISE_CONTROL_THERMAL: fan_config |= (1 << 4); break; |
| } |
| switch (sysfan_control) { |
| case FAN_CRUISE_CONTROL_SPEED: fan_config |= (2 << 2); break; |
| case FAN_CRUISE_CONTROL_THERMAL: fan_config |= (1 << 2); break; |
| } |
| // This register must be written first |
| hwm_write(0x04, fan_config); |
| |
| switch (cpufan_control) { |
| case FAN_CRUISE_CONTROL_SPEED: |
| printk_debug("Fan Cruise Control setting CPU fan to %d RPM\n", |
| fan_speeds[cpufan_speed].fan_speed); |
| hwm_write(0x06, fan_speeds[cpufan_speed].fan_in); // CPUFANIN target speed |
| break; |
| case FAN_CRUISE_CONTROL_THERMAL: |
| printk_debug("Fan Cruise Control setting CPU fan to activation at %d deg C/%d deg F\n", |
| temperatures[cpufan_temperature].deg_celsius, |
| temperatures[cpufan_temperature].deg_fahrenheit); |
| hwm_write(0x06, temperatures[cpufan_temperature].deg_celsius); // CPUFANIN target temperature |
| break; |
| } |
| |
| switch (sysfan_control) { |
| case FAN_CRUISE_CONTROL_SPEED: |
| printk_debug("Fan Cruise Control setting system fan to %d RPM\n", |
| fan_speeds[sysfan_speed].fan_speed); |
| hwm_write(0x05, fan_speeds[sysfan_speed].fan_in); // SYSFANIN target speed |
| break; |
| case FAN_CRUISE_CONTROL_THERMAL: |
| printk_debug("Fan Cruise Control setting system fan to activation at %d deg C/%d deg F\n", |
| temperatures[sysfan_temperature].deg_celsius, |
| temperatures[sysfan_temperature].deg_fahrenheit); |
| hwm_write(0x05, temperatures[sysfan_temperature].deg_celsius); // SYSFANIN target temperature |
| break; |
| } |
| |
| hwm_write(0x0e, 0x02); // Fan Output Step Down Time |
| hwm_write(0x0f, 0x02); // Fan Output Step Up Time |
| |
| hwm_write(0x47, 0xaf); // FAN divisor register |
| hwm_write(0x4b, 0x84); // AUXFANIN speed divisor |
| |
| hwm_write(0x40, 0x01); // Init, but no SMI# |
| } |
| |
| /* Audio Setup */ |
| |
| extern u32 * cim_verb_data; |
| extern u32 cim_verb_data_size; |
| |
| static void verb_setup(void) |
| { |
| // Default VERB is fine on this mainboard. |
| cim_verb_data = NULL; |
| cim_verb_data_size = 0; |
| } |
| |
| // mainboard_enable is executed as first thing after |
| // enumerate_buses(). |
| |
| static void mainboard_enable(device_t dev) |
| { |
| #if CONFIG_PCI_OPTION_ROM_RUN_YABEL |
| /* Install custom int15 handler for VGA OPROM */ |
| int15_install(); |
| #endif |
| verb_setup(); |
| hwm_setup(); |
| } |
| |
| struct chip_operations mainboard_ops = { |
| CHIP_NAME("Kontron 986LCD-M Mainboard") |
| .enable_dev = mainboard_enable, |
| }; |
| |