| fw_config |
| field DB_PORTS 0 3 |
| option DB_PORTS_NONE 0 |
| option DB_PORTS_2C_2A 1 |
| option DB_PORTS_1C_LTE 2 |
| option DB_PORTS_1A_HDMI 3 |
| option DB_PORTS_1C_1A 4 |
| option DB_PORTS_LTE_HDMI 5 |
| option DB_PORTS_1C_1A_LTE 6 |
| option DB_PORTS_1C 7 |
| option DB_PORTS_1A_HDMI_LTE 8 |
| end |
| field STYLUS 4 |
| option STYLUS_ABSENT 0 |
| option STYLUS_PRESENT 1 |
| end |
| field TABLETMODE 10 |
| option TABLETMODE_DISABLED 0 |
| option TABLETMODE_ENABLED 1 |
| end |
| field AUDIO_AMP 14 16 |
| option UNPROVISIONED 0 |
| option MAX98360 1 |
| option RT1015_I2C 2 |
| option RT1015P_AUTO 3 |
| option ALC5650 4 |
| end |
| field LTE 11 |
| option LTE_ABSENT 0 |
| option LTE_PRESENT 1 |
| end |
| field EXT_VR 18 |
| option EXT_VR_PRESENT 0 |
| option EXT_VR_ABSENT 1 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| device cpu_cluster 0 on end |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route, i.e., if this route changes then the affected GPE |
| # offset bits also need to be changed. |
| # DW0 is used by: |
| # - GPP_B3 - TRACKPAD_INT_ODL |
| # - GPP_B4 - H1_AP_INT_ODL |
| # DW1 is used by: |
| # - GPP_C12 - AP_PEN_DET_ODL |
| # DW2 is used by: |
| # - GPP_D0 - WWAN_HOST_WAKE |
| # - GPP_D3 - WLAN_PCIE_WAKE_ODL |
| # EC_AP_WAKE_ODL is routed to LAN_WAKE#/GPD02 & is part of DW3. |
| register "pmc_gpe0_dw0" = "PMC_GPP_B" |
| register "pmc_gpe0_dw1" = "PMC_GPP_C" |
| register "pmc_gpe0_dw2" = "PMC_GPP_D" |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| # EC memory map range is 0x900-0x9ff |
| register "gen3_dec" = "0x00fc0901" |
| |
| # USB Port Configuration |
| register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port C0 |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port C1 |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port A0 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port A1 |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # Discrete Bluetooth |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Integrated Bluetooth |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type-C Port C0 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type-C Port C1 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/1 Type-A Port A0 |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/1 Type-A Port A1 |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| }" |
| |
| register "SerialIoGSpiMode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoPci, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI2] = PchSerialIoDisabled, |
| }" |
| |
| register "SerialIoGSpiCsMode" = "{ |
| [PchSerialIoIndexGSPI0] = 1, |
| [PchSerialIoIndexGSPI1] = 0, |
| [PchSerialIoIndexGSPI2] = 0, |
| }" |
| |
| register "SerialIoGSpiCsState" = "{ |
| [PchSerialIoIndexGSPI0] = 0, |
| [PchSerialIoIndexGSPI1] = 0, |
| [PchSerialIoIndexGSPI2] = 0, |
| }" |
| |
| register "SerialIoUartMode" = "{ |
| [PchSerialIoIndexUART0] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART2] = PchSerialIoSkipInit, |
| }" |
| |
| # PCIE Root Port Configuration |
| register "PcieRpEnable[0]" = "0" |
| register "PcieRpEnable[1]" = "0" |
| register "PcieRpEnable[2]" = "0" |
| register "PcieRpEnable[3]" = "0" |
| register "PcieRpEnable[4]" = "0" |
| register "PcieRpEnable[5]" = "0" |
| register "PcieRpEnable[6]" = "0" |
| # PCIe Root Port 8 (index 7) hosts M.2 E-key WLAN. |
| register "PcieRpEnable[7]" = "1" |
| |
| register "PcieClkSrcUsage[0]" = "0xff" |
| register "PcieClkSrcUsage[1]" = "0xff" |
| register "PcieClkSrcUsage[2]" = "0xff" |
| # PCIe Clock Source 4 (index 3) is used by WLAN on PCIe Root Port 8 (index 7) |
| register "PcieClkSrcUsage[3]" = "7" |
| register "PcieClkSrcUsage[4]" = "0xff" |
| register "PcieClkSrcUsage[5]" = "0xff" |
| |
| # PCIE Clock Request to Clock Source Mapping |
| register "PcieClkSrcClkReq[0]" = "0" |
| register "PcieClkSrcClkReq[1]" = "1" |
| register "PcieClkSrcClkReq[2]" = "2" |
| register "PcieClkSrcClkReq[3]" = "3" |
| register "PcieClkSrcClkReq[4]" = "4" |
| register "PcieClkSrcClkReq[5]" = "5" |
| |
| # Audio related configurations |
| register "PchHdaDspEnable" = "1" |
| register "PchHdaAudioLinkHdaEnable" = "1" |
| register "PchHdaAudioLinkSspEnable[0]" = "1" |
| register "PchHdaAudioLinkSspEnable[1]" = "1" |
| register "PchHdaAudioLinkDmicEnable[0]" = "1" |
| register "PchHdaAudioLinkDmicEnable[1]" = "1" |
| |
| # Enable EMMC HS400 mode |
| register "ScsEmmcHs400Enabled" = "1" |
| |
| # GPIO for SD card detect |
| register "sdcard_cd_gpio" = "VGPIO_39" |
| # SD card power enable polarity |
| register "SdCardPowerEnableActiveHigh" = "1" |
| |
| # Enable S0ix support |
| register "s0ix_enable" = "1" |
| |
| # Display related UPDs |
| # Select eDP for port A |
| register "DdiPortAConfig" = "1" |
| |
| # Enable HPD for DDI ports B/C |
| register "DdiPortBHpd" = "1" |
| register "DdiPortCHpd" = "1" |
| # Enable DDC for DDI ports B/C |
| register "DdiPortBDdc" = "1" |
| register "DdiPortCDdc" = "1" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # Power limit config |
| register "power_limits_config[JSL_N4500_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "power_limits_config[JSL_N6000_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "power_limits_config[JSL_N5100_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "power_limits_config[JSL_N4505_10W_CORE]" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 25, |
| }" |
| |
| register "power_limits_config[JSL_N5105_10W_CORE]" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 25, |
| }" |
| |
| register "power_limits_config[JSL_N6005_10W_CORE]" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 25, |
| }" |
| |
| register "tcc_offset" = "10" # TCC of 90C |
| |
| # VR config settings |
| # Imon Slope correction specified in 1/100 increment values. Range is 0-200. |
| # Eg: 125 = 1.25 |
| register "ImonSlope" = "100" |
| |
| # Imon offset correction. Value is a 2's complement signed integer. |
| # Units 1/1000, Range 0-63999. |
| # For an offset = 12.580, use 12580 |
| register "ImonOffset" = "0" |
| |
| # Skip the CPU replacement check |
| register "SkipCpuReplacementCheck" = "1" |
| |
| # Sagv Configuration |
| register "SaGv" = "SaGv_Enabled" |
| |
| # Set the minimum assertion width |
| register "PchPmSlpS3MinAssert" = "3" # 50ms |
| register "PchPmSlpS4MinAssert" = "1" # 1s |
| register "PchPmSlpSusMinAssert" = "3" # 1s |
| register "PchPmSlpAMinAssert" = "3" # 98ms |
| |
| # NOTE: Duration programmed in the below register should never be smaller than the |
| # stretch duration programmed in the following registers - |
| # - GEN_PMCON_A.SLP_S3_MIN_ASST_WDTH (PchPmSlpS3MinAssert) |
| # - GEN_PMCON_A.S4MAW (PchPmSlpS4MinAssert) |
| # - PM_CFG.SLP_A_MIN_ASST_WDTH (PchPmSlpAMinAssert) |
| # - PM_CFG.SLP_LAN_MIN_ASST_WDTH |
| register "PchPmPwrCycDur" = "1" # 1s |
| |
| # Set xHCI LFPS period sampling off time, the default is 9ms. |
| register "xhci_lfps_sampling_offtime_ms" = "9" |
| |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on |
| register "gfx" = "GMA_DEFAULT_PANEL(0)" |
| end # Integrated Graphics Device |
| device pci 04.0 on |
| # Default DPTF Policy for all Dedede boards if not overridden |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 90, 10000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 80, 60000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 55, 15000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 15000) |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 80, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN) |
| }" |
| |
| ## Power Limits Control |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 6000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Ambient"" |
| register "options.tsr[2].desc" = ""Charger"" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 05.0 off end # IPU |
| device pci 09.0 off end # Intel Trace Hub |
| device pci 12.6 off end # GSPI 2 |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 2.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 2.3 on end |
| end |
| chip drivers/usb/acpi |
| device usb 2.4 off end |
| end |
| chip drivers/usb/acpi |
| device usb 2.5 off end |
| end |
| chip drivers/usb/acpi |
| device usb 2.6 off end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H19)" |
| device usb 2.7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 3.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.3 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.2 off end # PMC SRAM |
| device pci 14.3 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end # CNVi wifi |
| device pci 14.5 on end # SDCard |
| device pci 15.0 on end # I2C 0 |
| device pci 15.1 on end # I2C 1 |
| device pci 15.2 on end # I2C 2 |
| device pci 15.3 on end # I2C 3 |
| device pci 16.0 on end # HECI 1 |
| device pci 16.1 off end # HECI 2 |
| device pci 16.4 off end # HECI 3 |
| device pci 16.5 off end # HECI 4 |
| device pci 17.0 off end # SATA |
| device pci 19.0 on end # I2C 4 |
| device pci 19.1 off end # I2C 5 |
| device pci 19.2 on end # UART 2 |
| device pci 1a.0 on end # eMMC |
| device pci 1c.0 off end # PCI Express Root Port 1 |
| device pci 1c.1 off end # PCI Express Root Port 2 |
| device pci 1c.2 off end # PCI Express Root Port 3 |
| device pci 1c.3 off end # PCI Express Root Port 4 |
| device pci 1c.4 off end # PCI Express Root Port 5 |
| device pci 1c.5 off end # PCI Express Root Port 6 |
| device pci 1c.6 off end # PCI Express Root Port 7 |
| # External PCIe port 4 is mapped to PCIe Root port 8 |
| device pci 1c.7 on end # PCI Express Root Port 8 - WLAN |
| device pci 1e.0 off end # UART 0 |
| device pci 1e.1 off end # UART 1 |
| device pci 1e.2 on |
| chip drivers/spi/acpi |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cr50"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B4_IRQ)" |
| device spi 0 on end |
| end |
| end # GSPI 0 |
| device pci 1e.3 off end # GSPI 1 |
| device pci 1f.0 on |
| chip ec/google/chromeec |
| device pnp 0c09.0 on end |
| end |
| end # eSPI Interface |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 hidden end # Power Management Controller |
| device pci 1f.3 on |
| chip drivers/sof |
| register "spkr_tplg" = "rt1015" |
| register "jack_tplg" = "rt5682" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on |
| probe AUDIO_AMP RT1015_I2C |
| probe AUDIO_AMP RT1015P_AUTO |
| probe AUDIO_AMP UNPROVISIONED |
| end |
| end |
| chip drivers/sof |
| register "spkr_tplg" = "max98360a" |
| register "jack_tplg" = "rt5682" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on |
| probe AUDIO_AMP MAX98360 |
| end |
| end |
| end # Intel HDA/cAVS |
| device pci 1f.4 off end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.7 off end # Intel Trace Hub |
| end |
| end |