| /* |
| * This file is part of the coreboot project. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <device/pci_ops.h> |
| #include <device/pnp_ops.h> |
| #include <console/console.h> |
| #include <southbridge/intel/i82801jx/i82801jx.h> |
| #include <southbridge/intel/common/pmclib.h> |
| #include <northbridge/intel/x4x/x4x.h> |
| #include <cpu/x86/msr.h> |
| #include <cpu/intel/speedstep.h> |
| #include <arch/romstage.h> |
| #include <cf9_reset.h> |
| #include <superio/winbond/w83627dhg/w83627dhg.h> |
| #include <superio/winbond/common/winbond.h> |
| |
| #define SERIAL_DEV PNP_DEV(0x2e, W83627DHG_SP1) |
| #define GPIO_DEV PNP_DEV(0x2e, W83627DHG_GPIO2345_V) |
| #define LPC_DEV PCI_DEV(0, 0x1f, 0) |
| |
| static u8 msr_get_fsb(void) |
| { |
| u8 fsbcfg; |
| msr_t msr; |
| const u32 eax = cpuid_eax(1); |
| |
| /* Netburst */ |
| if (((eax >> 8) & 0xf) == 0xf) { |
| msr = rdmsr(MSR_EBC_FREQUENCY_ID); |
| fsbcfg = (msr.lo >> 16) & 0x7; |
| } else { /* Intel Core 2 */ |
| msr = rdmsr(MSR_FSB_FREQ); |
| fsbcfg = msr.lo & 0x7; |
| } |
| |
| return fsbcfg; |
| } |
| |
| /* BSEL MCH straps are not hooked up to the CPU as usual but to the SIO */ |
| static int setup_sio_gpio(void) |
| { |
| int need_reset = 0; |
| u8 reg, old_reg; |
| |
| u8 bsel = msr_get_fsb(); |
| switch (bsel) { |
| case 0: |
| case 2: |
| case 4: |
| break; |
| default: |
| printk(BIOS_WARNING, |
| "BSEL: Unsupported FSB frequency, using 800MHz\n"); |
| bsel = 2; /* 800MHz */ |
| break; |
| } |
| |
| pnp_enter_ext_func_mode(GPIO_DEV); |
| pnp_set_logical_device(GPIO_DEV); |
| |
| /* |
| * P5QL-EM: |
| * BSEL0 -> not hooked up (not supported anyways) |
| * BSEL1 -> GPIO33 (inverted) |
| * BSEL2 -> GPIO40 |
| */ |
| reg = 0x92; |
| /* Multi-function Pin Selection */ |
| old_reg = pnp_read_config(GPIO_DEV, 0x2c); |
| pnp_write_config(GPIO_DEV, 0x2c, reg); |
| need_reset = (reg != old_reg); |
| |
| pnp_write_config(GPIO_DEV, 0x30, 0x0e); /* Enable GPIO3x,4x,5x */ |
| pnp_write_config(GPIO_DEV, 0xf0, 0xf3); /* GPIO3x direction */ |
| pnp_write_config(GPIO_DEV, 0xf2, 0x08); /* GPIO3x inversion */ |
| pnp_write_config(GPIO_DEV, 0xf4, 0x06); /* GPIO4x direction */ |
| |
| const int gpio33 = (bsel & 2) >> 1; |
| const int gpio40 = (bsel & 4) >> 2; |
| reg = (gpio33 << 3); |
| old_reg = pnp_read_config(GPIO_DEV, 0xf1); /* GPIO3x data */ |
| /* Set GPIO32 high like vendor firmware */ |
| pnp_write_config(GPIO_DEV, 0xf1, old_reg | reg | 4); |
| need_reset += ((reg & 0x8) != (old_reg & 0x8)); |
| |
| reg = gpio40; |
| old_reg = pnp_read_config(GPIO_DEV, 0xf5); /* GPIO4x data */ |
| pnp_write_config(GPIO_DEV, 0xf5, old_reg | reg); |
| need_reset += ((reg & 0x1) != (old_reg & 0x1)); |
| pnp_exit_ext_func_mode(GPIO_DEV); |
| |
| return need_reset; |
| } |
| |
| void mainboard_romstage_entry(void) |
| { |
| /* This board has first dimm slot of each channel hooked up to |
| rank0 and rank1, while the second dimm slot is only connected |
| to rank1. The raminit does not support such setups |
| const u8 spd_addrmap[4] = { 0x50, 0x51, 0x52, 0x53 }; */ |
| const u8 spd_addrmap[4] = { 0x50, 0, 0x52, 0 }; |
| u8 boot_path = 0; |
| u8 s3_resume; |
| |
| /* Set southbridge and Super I/O GPIOs. */ |
| i82801jx_lpc_setup(); |
| winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); |
| |
| console_init(); |
| |
| enable_smbus(); |
| |
| i82801jx_early_init(); |
| x4x_early_init(); |
| |
| s3_resume = southbridge_detect_s3_resume(); |
| if (s3_resume) |
| boot_path = BOOT_PATH_RESUME; |
| if (MCHBAR32(PMSTS_MCHBAR) & PMSTS_WARM_RESET) |
| boot_path = BOOT_PATH_WARM_RESET; |
| |
| if (!s3_resume && setup_sio_gpio()) { |
| printk(BIOS_DEBUG, "Needs reset to configure CPU BSEL straps\n"); |
| full_reset(); |
| } |
| |
| sdram_initialize(boot_path, spd_addrmap); |
| |
| x4x_late_init(s3_resume); |
| |
| printk(BIOS_DEBUG, "x4x late init complete\n"); |
| } |