| /* $NoKeywords:$ */ |
| /** |
| * @file |
| * |
| * mnphy.c |
| * |
| * Common Northbridge Phy support |
| * |
| * @xrefitem bom "File Content Label" "Release Content" |
| * @e project: AGESA |
| * @e sub-project: (Mem/NB) |
| * @e \$Revision: 38306 $ @e \$Date: 2010-09-22 01:51:51 +0800 (Wed, 22 Sep 2010) $ |
| * |
| **/ |
| /* |
| ***************************************************************************** |
| * |
| * Copyright (c) 2011, Advanced Micro Devices, Inc. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are met: |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * * Neither the name of Advanced Micro Devices, Inc. nor the names of |
| * its contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND |
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED |
| * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL ADVANCED MICRO DEVICES, INC. BE LIABLE FOR ANY |
| * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES |
| * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; |
| * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND |
| * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS |
| * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| * *************************************************************************** |
| * |
| */ |
| |
| |
| /* |
| *---------------------------------------------------------------------------- |
| * MODULES USED |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| |
| |
| |
| #include "AGESA.h" |
| #include "amdlib.h" |
| #include "Ids.h" |
| #include "mport.h" |
| #include "mm.h" |
| #include "mn.h" |
| #include "mt.h" |
| #include "mu.h" |
| #include "PlatformMemoryConfiguration.h" |
| #include "heapManager.h" |
| #include "merrhdl.h" |
| #include "Filecode.h" |
| CODE_GROUP (G1_PEICC) |
| RDATA_GROUP (G1_PEICC) |
| #define FILECODE PROC_MEM_NB_MNPHY_FILECODE |
| /*---------------------------------------------------------------------------- |
| * DEFINITIONS AND MACROS |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| #define UNUSED_CLK 4 |
| |
| /*---------------------------------------------------------------------------- |
| * TYPEDEFS AND STRUCTURES |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| /// Type of an entry for processing phy init compensation for client NB |
| typedef struct { |
| BIT_FIELD_NAME IndexBitField; ///< Bit field on which the value is decided |
| BIT_FIELD_NAME StartTargetBitField; ///< First bit field to be modified |
| BIT_FIELD_NAME EndTargetBitField; ///< Last bit field to be modified |
| UINT16 ExtraValue; ///< Extra value needed to be written to bit field |
| CONST UINT16 (*TxPrePN)[3][5]; ///< Pointer to slew rate table |
| } PHY_COMP_INIT_CLIENTNB; |
| |
| /*---------------------------------------------------------------------------- |
| * PROTOTYPES OF LOCAL FUNCTIONS |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| |
| |
| |
| /*---------------------------------------------------------------------------- |
| * EXPORTED FUNCTIONS |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function gets a delay value a PCI register during training |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - type of delay to be set |
| * @param[in] DrbnVar - encoding of Dimm-Rank-Byte-Nibble to be accessed |
| * (use either DIMM_BYTE_ACCESS(dimm,byte) or CS_NBBL_ACCESS(cs,nibble) to use this encoding |
| * |
| * @return Value read |
| */ |
| |
| UINT32 |
| MemNGetTrainDlyNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN TRN_DLY_TYPE TrnDly, |
| IN DRBN DrbnVar |
| ) |
| { |
| return NBPtr->MemNcmnGetSetTrainDly (NBPtr, 0, TrnDly, DrbnVar, 0); |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function sets a delay value a PCI register during training |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - type of delay to be set |
| * @param[in] DrbnVar - encoding of Dimm-Rank-Byte-Nibble to be accessed |
| * (use either DIMM_BYTE_ACCESS(dimm,byte) or CS_NBBL_ACCESS(cs,nibble) to use this encoding |
| * @param[in] Field - Value to be programmed |
| * |
| */ |
| |
| VOID |
| MemNSetTrainDlyNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN TRN_DLY_TYPE TrnDly, |
| IN DRBN DrbnVar, |
| IN UINT16 Field |
| ) |
| { |
| NBPtr->MemNcmnGetSetTrainDly (NBPtr, 1, TrnDly, DrbnVar, Field); |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function executes prototypical Phy fence training function. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNPhyFenceTrainingNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| NBPtr->MemPPhyFenceTrainingNb (NBPtr); |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function executes prototypical Phy fence training function. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNPhyFenceTrainingUnb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| UINT8 FenceThresholdTxDll; |
| UINT8 FenceThresholdRxDll; |
| UINT8 FenceThresholdTxPad; |
| UINT16 Fence2Data; |
| |
| // 1. Program D18F2x[1,0]9C_x0000_0008[FenceTrSel]=10b. |
| // 2. Perform phy fence training. |
| // 3. Write the calculated fence value to D18F2x[1,0]9C_x0000_000C[FenceThresholdTxDll]. |
| MemNSetBitFieldNb (NBPtr, BFFenceTrSel, 2); |
| MAKE_TSEFO (NBPtr->NBRegTable, DCT_PHY_ACCESS, 0x0C, 30, 26, BFPhyFence); |
| IDS_HDT_CONSOLE (MEM_FLOW, "\t\tFenceThresholdTxDll\n"); |
| MemNTrainPhyFenceNb (NBPtr); |
| FenceThresholdTxDll = (UINT8) MemNGetBitFieldNb (NBPtr, BFPhyFence); |
| NBPtr->FamilySpecificHook[DetectMemPllError] (NBPtr, &FenceThresholdTxDll); |
| |
| // 4. Program D18F2x[1,0]9C_x0D0F_0[F,7:0]0F[AlwaysEnDllClks]=001b. |
| MemNSetBitFieldNb (NBPtr, BFAlwaysEnDllClks, 0x1000); |
| |
| // 5. Program D18F2x[1,0]9C_x0000_0008[FenceTrSel]=01b. |
| // 6. Perform phy fence training. |
| // 7. Write the calculated fence value to D18F2x[1,0]9C_x0000_000C[FenceThresholdRxDll]. |
| MemNSetBitFieldNb (NBPtr, BFFenceTrSel, 1); |
| MAKE_TSEFO (NBPtr->NBRegTable, DCT_PHY_ACCESS, 0x0C, 25, 21, BFPhyFence); |
| IDS_HDT_CONSOLE (MEM_FLOW, "\n\t\tFenceThresholdRxDll\n"); |
| MemNTrainPhyFenceNb (NBPtr); |
| FenceThresholdRxDll = (UINT8) MemNGetBitFieldNb (NBPtr, BFPhyFence); |
| NBPtr->FamilySpecificHook[DetectMemPllError] (NBPtr, &FenceThresholdRxDll); |
| |
| // 8. Program D18F2x[1,0]9C_x0D0F_0[F,7:0]0F[AlwaysEnDllClks]=000b. |
| MemNSetBitFieldNb (NBPtr, BFAlwaysEnDllClks, 0x0000); |
| |
| // 9. Program D18F2x[1,0]9C_x0000_0008[FenceTrSel]=11b. |
| // 10. Perform phy fence training. |
| // 11. Write the calculated fence value to D18F2x[1,0]9C_x0000_000C[FenceThresholdTxPad]. |
| MemNSetBitFieldNb (NBPtr, BFFenceTrSel, 3); |
| MAKE_TSEFO (NBPtr->NBRegTable, DCT_PHY_ACCESS, 0x0C, 20, 16, BFPhyFence); |
| IDS_HDT_CONSOLE (MEM_FLOW, "\n\t\tFenceThresholdTxPad\n"); |
| MemNTrainPhyFenceNb (NBPtr); |
| FenceThresholdTxPad = (UINT8) MemNGetBitFieldNb (NBPtr, BFPhyFence); |
| NBPtr->FamilySpecificHook[DetectMemPllError] (NBPtr, &FenceThresholdTxPad); |
| |
| // Program Fence2 threshold for Clk, Cmd, and Addr |
| if (FenceThresholdTxPad < 16) { |
| MemNSetBitFieldNb (NBPtr, BFClkFence2, FenceThresholdTxPad | 0x10); |
| MemNSetBitFieldNb (NBPtr, BFCmdFence2, FenceThresholdTxPad | 0x10); |
| MemNSetBitFieldNb (NBPtr, BFAddrFence2, FenceThresholdTxPad | 0x10); |
| } else { |
| MemNSetBitFieldNb (NBPtr, BFClkFence2, 0); |
| MemNSetBitFieldNb (NBPtr, BFCmdFence2, 0); |
| MemNSetBitFieldNb (NBPtr, BFAddrFence2, 0); |
| } |
| |
| // Program Fence2 threshold for data |
| Fence2Data = 0; |
| if (FenceThresholdTxPad < 16) { |
| Fence2Data |= FenceThresholdTxPad | 0x10; |
| } |
| if (FenceThresholdRxDll < 16) { |
| Fence2Data |= (FenceThresholdRxDll | 0x10) << 10; |
| } |
| if (FenceThresholdTxDll < 16) { |
| Fence2Data |= (FenceThresholdTxDll | 0x10) << 5; |
| } |
| MemNSetBitFieldNb (NBPtr, BFDataFence2, Fence2Data); |
| |
| if (NBPtr->MCTPtr->Status[SbLrdimms]) { |
| // 18. If motherboard routing requires CS[7:6] to adopt address timings, e.g. 3 LRDIMMs/ch with CS[7:6] |
| // routed across all DIMM sockets, BIOS performs the following: |
| if (FindPSOverrideEntry (NBPtr->RefPtr->PlatformMemoryConfiguration, PSO_NO_LRDIMM_CS67_ROUTING, NBPtr->MCTPtr->SocketId, NBPtr->ChannelPtr->ChannelID) != NULL) { |
| // A. Program D18F2xA8_dct[1:0][CSTimingMux67] = 1. |
| MemNSetBitFieldNb (NBPtr, BFCSTimingMux67, 1); |
| // B. Program D18F2x9C_x0D0F_8021_dct[1:0]: |
| // - DiffTimingEn = 1. |
| // - IF (D18F2x9C_x0000_0004_dct[1:0][AddrCmdFineDelay] >= |
| // D18F2x9C_x0D0F_E008_dct[1:0][FenceValue]) THEN Fence = 1 ELSE Fence = 0. |
| // - Delay = D18F2x9C_x0000_0004_dct[1:0][AddrCmdFineDelay]. |
| // |
| MemNSetBitFieldNb (NBPtr, BFDiffTimingEn, 1); |
| MemNSetBitFieldNb (NBPtr, BFFence, (MemNGetBitFieldNb (NBPtr, BFAddrCmdFineDelay) >= MemNGetBitFieldNb (NBPtr, BFFenceValue)) ? 1 : 0); |
| MemNSetBitFieldNb (NBPtr, BFDelay, (MemNGetBitFieldNb (NBPtr, BFAddrCmdFineDelay))); |
| } |
| } |
| |
| // 19. Reprogram F2x9C_04. |
| MemNSetBitFieldNb (NBPtr, BFAddrTmgControl, MemNGetBitFieldNb (NBPtr, BFAddrTmgControl)); |
| |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function executes Phy fence training |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNTrainPhyFenceNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| UINT8 Byte; |
| UINT16 Avg; |
| UINT8 PREvalue; |
| |
| if (MemNGetBitFieldNb (NBPtr, BFDisDramInterface)) { |
| return; |
| } |
| |
| // 1. BIOS first programs a seed value to the phase recovery |
| // engine registers. |
| // |
| IDS_HDT_CONSOLE (MEM_FLOW, "\t\tSeeds: "); |
| for (Byte = 0; Byte < MAX_BYTELANES_PER_CHANNEL; Byte++) { |
| // This includes ECC as byte 8 |
| MemNSetTrainDlyNb (NBPtr, AccessPhRecDly, DIMM_BYTE_ACCESS (0, Byte), 19); |
| IDS_HDT_CONSOLE (MEM_FLOW, "%02x ", 19); |
| } |
| |
| IDS_HDT_CONSOLE (MEM_FLOW, "\n\t\tPhyFenceTrEn = 1"); |
| // 2. Set F2x[1, 0]9C_x08[PhyFenceTrEn]=1. |
| MemNSetBitFieldNb (NBPtr, BFPhyFenceTrEn, 1); |
| |
| if (!NBPtr->IsSupported[UnifiedNbFence]) { |
| // 3. Wait 200 MEMCLKs. |
| MemNWaitXMemClksNb (NBPtr, 200); |
| } else { |
| // 3. Wait 2000 MEMCLKs. |
| MemNWaitXMemClksNb (NBPtr, 2000); |
| } |
| |
| // 4. Clear F2x[1, 0]9C_x08[PhyFenceTrEn]=0. |
| MemNSetBitFieldNb (NBPtr, BFPhyFenceTrEn, 0); |
| |
| // 5. BIOS reads the phase recovery engine registers |
| // F2x[1, 0]9C_x[51:50] and F2x[1, 0]9C_x52. |
| // 6. Calculate the average value of the fine delay and subtract 8. |
| // |
| Avg = 0; |
| IDS_HDT_CONSOLE (MEM_FLOW, "\n\t\t PRE: "); |
| for (Byte = 0; Byte < MAX_BYTELANES_PER_CHANNEL; Byte++) { |
| // |
| // This includes ECC as byte 8. ECC Byte lane (8) is ignored by MemNGetTrainDlyNb function where |
| // ECC is not supported. |
| // |
| PREvalue = (UINT8) (0x1F & MemNGetTrainDlyNb (NBPtr, AccessPhRecDly, DIMM_BYTE_ACCESS (0, Byte))); |
| Avg = Avg + ((UINT16) PREvalue); |
| IDS_HDT_CONSOLE (MEM_FLOW, "%02x ", PREvalue); |
| } |
| Avg = ((Avg + 8) / 9); // round up |
| |
| Avg -= 8; |
| NBPtr->MemNPFenceAdjustNb (NBPtr, &Avg); |
| |
| IDS_HDT_CONSOLE (MEM_FLOW, "\n\t\tFence: %02x\n", Avg); |
| |
| // 7. Write the value to F2x[1, 0]9C_x0C[PhyFence]. |
| MemNSetBitFieldNb (NBPtr, BFPhyFence, Avg); |
| |
| // 8. BIOS rewrites F2x[1, 0]9C_x04, DRAM Address/Command Timing Control |
| // Register delays for both channels. This forces the phy to recompute |
| // the fence. |
| // |
| MemNSetBitFieldNb (NBPtr, BFAddrTmgControl, MemNGetBitFieldNb (NBPtr, BFAddrTmgControl)); |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function initializes the DDR phy compensation logic |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNInitPhyCompNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| CONST UINT8 TableCompRiseSlew20x[] = {7, 3, 2, 2}; |
| CONST UINT8 TableCompRiseSlew15x[] = {7, 7, 3, 2}; |
| CONST UINT8 TableCompFallSlew20x[] = {7, 5, 3, 2}; |
| CONST UINT8 TableCompFallSlew15x[] = {7, 7, 5, 3}; |
| UINT8 i; |
| UINT8 j; |
| UINT8 CurrDct; |
| UINT8 CurrChannel; |
| BOOLEAN MarginImprv; |
| MarginImprv = FALSE; |
| CurrDct = NBPtr->Dct; |
| CurrChannel = NBPtr->Channel; |
| if (NBPtr->IsSupported[CheckSlewWithMarginImprv]) { |
| if (NBPtr->MCTPtr->GangedMode == FALSE) { |
| for (i = 0; i < NBPtr->DctCount; i++) { |
| MemNSwitchDCTNb (NBPtr, i); |
| for (j = 0; j < NBPtr->ChannelCount; j++) { |
| NBPtr->SwitchChannel (NBPtr, j); |
| if ((NBPtr->ChannelPtr->Dimms == 4) && ((NBPtr->DCTPtr->Timings.Speed == DDR533_FREQUENCY) || (NBPtr->DCTPtr->Timings.Speed == DDR667_FREQUENCY))) { |
| MarginImprv = TRUE; |
| } |
| } |
| } |
| MemNSwitchDCTNb (NBPtr, CurrDct); |
| NBPtr->SwitchChannel (NBPtr, CurrChannel); |
| } |
| } |
| |
| // 1. BIOS disables the phy compensation register by programming F2x9C_x08[DisAutoComp]=1 |
| // 2. BIOS waits 5 us for the disabling of the compensation engine to complete. |
| // DisAutoComp will be cleared after Dram init has completed |
| // |
| MemNSwitchDCTNb (NBPtr, 0); |
| MemNSetBitFieldNb (NBPtr, BFDisAutoComp, 1); |
| MemUWait10ns (500, NBPtr->MemPtr); |
| MemNSwitchDCTNb (NBPtr, CurrDct); |
| |
| // 3. For each normalized driver strength code read from |
| // F2x[1, 0]9C_x00[AddrCmdDrvStren], program the |
| // corresponding 3 bit predriver code in F2x9C_x0A[D3Cmp1NCal, D3Cmp1PCal]. |
| // |
| // 4. For each normalized driver strength code read from |
| // F2x[1, 0]9C_x00[DataDrvStren], program the corresponding |
| // 3 bit predriver code in F2x9C_x0A[D3Cmp0NCal, D3Cmp0PCal, D3Cmp2NCal, |
| // D3Cmp2PCal]. |
| // |
| j = (UINT8) MemNGetBitFieldNb (NBPtr, BFAddrCmdDrvStren); |
| i = (UINT8) MemNGetBitFieldNb (NBPtr, BFDataDrvStren); |
| |
| MemNSwitchDCTNb (NBPtr, 0); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp1NCal, TableCompRiseSlew20x[j]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp1PCal, TableCompFallSlew20x[j]); |
| |
| if (NBPtr->IsSupported[CheckSlewWithMarginImprv]) { |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp0NCal, (MarginImprv) ? 0 : TableCompRiseSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp0PCal, (MarginImprv) ? 0 : TableCompFallSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp2NCal, (MarginImprv) ? 0 : TableCompRiseSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp2PCal, (MarginImprv) ? 0 : TableCompFallSlew15x[i]); |
| } |
| if (NBPtr->IsSupported[CheckSlewWithoutMarginImprv]) { |
| ASSERT (i <= 3); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp0NCal, TableCompRiseSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp0PCal, TableCompFallSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp2NCal, TableCompRiseSlew15x[i]); |
| MemNSetBitFieldNb (NBPtr, BFD3Cmp2PCal, TableCompFallSlew15x[i]); |
| } |
| MemNSwitchDCTNb (NBPtr, CurrDct); |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This is a general purpose function that executes before DRAM training |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNBeforeDQSTrainingNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| UINT8 Dct; |
| UINT8 ChipSel; |
| UINT32 TestAddrRJ16; |
| UINT32 RealAddr; |
| |
| MemTBeginTraining (NBPtr->TechPtr); |
| |
| for (Dct = 0; Dct < NBPtr->DctCount; Dct++) { |
| MemNSwitchDCTNb (NBPtr, Dct); |
| if (NBPtr->DCTPtr->Timings.DctMemSize != 0) { |
| for (ChipSel = 0; ChipSel < MAX_CS_PER_CHANNEL; ChipSel += 2) { |
| if (MemNGetMCTSysAddrNb (NBPtr, ChipSel, &TestAddrRJ16)) { |
| |
| RealAddr = MemUSetUpperFSbase (TestAddrRJ16, NBPtr->MemPtr); |
| |
| MemUDummyCLRead (RealAddr); |
| |
| MemNSetBitFieldNb (NBPtr, BFErr350, 0x8000); |
| MemUWait10ns (60, NBPtr->MemPtr); // Wait 300ns |
| MemNSetBitFieldNb (NBPtr, BFErr350, 0x0000); |
| MemUWait10ns (400, NBPtr->MemPtr); // Wait 2us |
| MemUProcIOClFlush (TestAddrRJ16, 1, NBPtr->MemPtr); |
| break; |
| } |
| } |
| } |
| if (NBPtr->IsSupported[CheckEccDLLPwrDnConfig]) { |
| if (!NBPtr->MCTPtr->Status[SbEccDimms]) { |
| MemNSetBitFieldNb (NBPtr, BFEccDLLPwrDnConf, 0x0010); |
| } |
| if (NBPtr->DCTPtr->Timings.Dimmx4Present == 0) { |
| MemNSetBitFieldNb (NBPtr, BFEccDLLConf, 0x0080); |
| } |
| } |
| } |
| |
| MemTEndTraining (NBPtr->TechPtr); |
| } |
| |
| /*-----------------------------------------------------------------------------*/ |
| /** |
| * |
| * Returns the parameters for a requested delay value to be used in training |
| * The correct Min, Max and Mask are determined based on the type of Delay, |
| * and the frequency |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - Type of delay |
| * @param[in,out] *Parms - Pointer to the TRN_DLY-PARMS struct |
| * |
| */ |
| |
| VOID |
| MemNGetTrainDlyParmsNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN TRN_DLY_TYPE TrnDly, |
| IN OUT TRN_DLY_PARMS *Parms |
| ) |
| { |
| Parms->Min = 0; |
| |
| if (TrnDly == AccessWrDatDly) { |
| Parms->Max = 0x1F; |
| Parms->Mask = 0x01F; |
| } else if (TrnDly == AccessRdDqsDly) { |
| if ( (NBPtr->IsSupported[CheckMaxRdDqsDlyPtr]) && (NBPtr->DCTPtr->Timings.Speed > DDR667_FREQUENCY) ) { |
| Parms->Max = 0x3E; |
| Parms->Mask = 0x03E; |
| } else { |
| Parms->Max = 0x1F; |
| Parms->Mask = 0x01F; |
| } |
| } |
| } |
| |
| /*-----------------------------------------------------------------------------*/ |
| /** |
| * |
| * Returns the parameters for a requested delay value to be used in training |
| * The correct Min, Max and Mask are determined based on the type of Delay, |
| * and the frequency |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - Type of delay |
| * @param[in,out] *Parms - Pointer to the TRN_DLY-PARMS struct |
| * |
| */ |
| |
| VOID |
| MemNGetTrainDlyParmsClientNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN TRN_DLY_TYPE TrnDly, |
| IN OUT TRN_DLY_PARMS *Parms |
| ) |
| { |
| Parms->Min = 0; |
| |
| if (TrnDly == AccessWrDatDly) { |
| Parms->Max = 0x1F; |
| Parms->Mask = 0x01F; |
| } else if (TrnDly == AccessRdDqsDly) { |
| Parms->Max = 0x3E; |
| Parms->Mask = 0x03E; |
| } |
| } |
| /*-----------------------------------------------------------------------------*/ |
| /** |
| * |
| * Returns the parameters for a requested delay value to be used in training |
| * The correct Min, Max and Mask are determined based on the type of Delay, |
| * and the frequency |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - Type of delay |
| * @param[in,out] *Parms - Pointer to the TRN_DLY-PARMS struct |
| * |
| */ |
| |
| VOID |
| MemNGetTrainDlyParmsUnb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN TRN_DLY_TYPE TrnDly, |
| IN OUT TRN_DLY_PARMS *Parms |
| ) |
| { |
| Parms->Min = 0; |
| |
| if (TrnDly == AccessWrDatDly) { |
| Parms->Max = 0x1F; |
| Parms->Mask = 0x01F; |
| } else if (TrnDly == AccessRdDqsDly) { |
| Parms->Max = 0x1F; |
| Parms->Mask = 0x01F; |
| } |
| } |
| /*---------------------------------------------------------------------------- |
| * LOCAL FUNCTIONS |
| * |
| *---------------------------------------------------------------------------- |
| */ |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function gets or set DQS timing during training. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] TrnDly - type of delay to be set |
| * @param[in] DrbnVar - encoding of Dimm-Rank-Byte-Nibble to be accessed |
| * (use either DIMM_BYTE_ACCESS(dimm,byte) or CS_NBBL_ACCESS(cs,nibble) to use this encoding |
| * @param[in] Field - Value to be programmed |
| * @param[in] IsSet - Indicates if the function will set or get |
| * |
| * @return value read, if the function is used as a "get" |
| */ |
| |
| UINT32 |
| MemNcmnGetSetTrainDlyNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN UINT8 IsSet, |
| IN TRN_DLY_TYPE TrnDly, |
| IN DRBN DrbnVar, |
| IN UINT16 Field |
| ) |
| { |
| UINT16 Index; |
| UINT16 Offset; |
| UINT32 Value; |
| UINT32 Address; |
| UINT8 Dimm; |
| UINT8 Rank; |
| UINT8 Byte; |
| UINT8 Nibble; |
| |
| Dimm = DRBN_DIMM (DrbnVar); |
| Rank = DRBN_RANK (DrbnVar); |
| Byte = DRBN_BYTE (DrbnVar); |
| Nibble = DRBN_NBBL (DrbnVar); |
| |
| ASSERT (Dimm < 4); |
| ASSERT (Byte <= ECC_DLY); |
| |
| switch (TrnDly) { |
| case AccessRcvEnDly: |
| Index = 0x10; |
| break; |
| case AccessWrDqsDly: |
| Index = 0x30; |
| break; |
| case AccessWrDatDly: |
| Index = 0x01; |
| break; |
| case AccessRdDqsDly: |
| Index = 0x05; |
| break; |
| case AccessPhRecDly: |
| Index = 0x50; |
| break; |
| default: |
| Index = 0; |
| IDS_ERROR_TRAP; |
| } |
| |
| switch (TrnDly) { |
| case AccessRcvEnDly: |
| case AccessWrDqsDly: |
| Index += (Dimm * 3); |
| if (Byte & 0x04) { |
| // if byte 4,5,6,7 |
| Index += 0x10; |
| } |
| if (Byte & 0x02) { |
| // if byte 2,3,6,7 |
| Index++; |
| } |
| if (Byte > 7) { |
| Index += 2; |
| } |
| Offset = 16 * (Byte % 2); |
| Index |= (Rank << 8); |
| Index |= (Nibble << 9); |
| break; |
| |
| case AccessRdDqsDly: |
| case AccessWrDatDly: |
| |
| if (NBPtr->IsSupported[DimmBasedOnSpeed]) { |
| if (NBPtr->DCTPtr->Timings.Speed < DDR800_FREQUENCY) { |
| // if DDR speed is below 800, use DIMM 0 delays for all DIMMs. |
| Dimm = 0; |
| } |
| } |
| |
| Index += (Dimm * 0x100); |
| if (Nibble) { |
| if (Rank) { |
| Index += 0xA0; |
| } else { |
| Index += 0x70; |
| } |
| } else if (Rank) { |
| Index += 0x60; |
| } |
| // fall through - AccessRdDqsDly and AccessWrDatDly also need to run AccessPhRecDly sequence |
| case AccessPhRecDly: |
| Index += (Byte / 4); |
| Offset = 8 * (Byte % 4); |
| break; |
| default: |
| Offset = 0; |
| IDS_ERROR_TRAP; |
| } |
| |
| Address = Index; |
| MemNSetBitFieldNb (NBPtr, BFDctAddlOffsetReg, Address); |
| MemNPollBitFieldNb (NBPtr, BFDctAccessDone, 1, PCI_ACCESS_TIMEOUT, FALSE); |
| Value = MemNGetBitFieldNb (NBPtr, BFDctAddlDataReg); |
| |
| if (TrnDly == AccessRdDqsDly) { |
| NBPtr->FamilySpecificHook[AdjustRdDqsDlyOffset] (NBPtr, &Offset); |
| } |
| |
| if (IsSet) { |
| if (TrnDly == AccessPhRecDly) { |
| Value = NBPtr->DctCachePtr->PhRecReg[Index & 0x03]; |
| } |
| |
| Value = ((UINT32)Field << Offset) | (Value & (~((UINT32) ((TrnDly == AccessRcvEnDly) ? 0x1FF : 0xFF) << Offset))); |
| MemNSetBitFieldNb (NBPtr, BFDctAddlDataReg, Value); |
| Address |= DCT_ACCESS_WRITE; |
| MemNSetBitFieldNb (NBPtr, BFDctAddlOffsetReg, Address); |
| MemNPollBitFieldNb (NBPtr, BFDctAccessDone, 1, PCI_ACCESS_TIMEOUT, FALSE); |
| |
| if (TrnDly == AccessPhRecDly) { |
| NBPtr->DctCachePtr->PhRecReg[Index & 0x03] = Value; |
| } |
| } else { |
| Value = (Value >> Offset) & (UINT32) ((TrnDly == AccessRcvEnDly) ? 0x1FF : 0xFF); |
| } |
| |
| return Value; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function gets or set DQS timing during training. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] IsSet - Indicates if the function will set or get |
| * @param[in] TrnDly - type of delay to be set |
| * @param[in] DrbnVar - encoding of Dimm-Rank-Byte-Nibble to be accessed |
| * (use either DIMM_BYTE_ACCESS(dimm,byte) or CS_NBBL_ACCESS(cs,nibble) to use this encoding |
| * @param[in] Field - Value to be programmed |
| * |
| * @return value read, if the function is used as a "get" |
| */ |
| UINT32 |
| MemNcmnGetSetTrainDlyClientNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN UINT8 IsSet, |
| IN TRN_DLY_TYPE TrnDly, |
| IN DRBN DrbnVar, |
| IN UINT16 Field |
| ) |
| { |
| UINT16 Index; |
| UINT16 Offset; |
| UINT32 Value; |
| UINT32 Address; |
| UINT8 Dimm; |
| UINT8 Byte; |
| |
| Dimm = DRBN_DIMM (DrbnVar); |
| Byte = DRBN_BYTE (DrbnVar); |
| |
| ASSERT (Dimm < 2); |
| ASSERT (Byte <= ECC_DLY); |
| |
| if ((Byte > 7)) { |
| // Llano does not support ECC delay, so: |
| if (IsSet) { |
| // On write, ignore |
| return 0; |
| } else { |
| // On read, redirect to byte 0 to correct fence averaging |
| Byte = 0; |
| } |
| } |
| |
| switch (TrnDly) { |
| case AccessRcvEnDly: |
| Index = 0x10; |
| break; |
| case AccessWrDqsDly: |
| Index = 0x30; |
| break; |
| case AccessWrDatDly: |
| Index = 0x01; |
| break; |
| case AccessRdDqsDly: |
| Index = 0x05; |
| break; |
| case AccessPhRecDly: |
| Index = 0x50; |
| break; |
| default: |
| Index = 0; |
| IDS_ERROR_TRAP; |
| } |
| |
| switch (TrnDly) { |
| case AccessRcvEnDly: |
| case AccessWrDqsDly: |
| Index += (Dimm * 3); |
| if (Byte & 0x04) { |
| // if byte 4,5,6,7 |
| Index += 0x10; |
| } |
| if (Byte & 0x02) { |
| // if byte 2,3,6,7 |
| Index++; |
| } |
| Offset = 16 * (Byte % 2); |
| break; |
| |
| case AccessRdDqsDly: |
| case AccessWrDatDly: |
| Index += (Dimm * 0x100); |
| // fall through - AccessRdDqsDly and AccessWrDatDly also need to run AccessPhRecDly sequence |
| case AccessPhRecDly: |
| Index += (Byte / 4); |
| Offset = 8 * (Byte % 4); |
| break; |
| default: |
| Offset = 0; |
| IDS_ERROR_TRAP; |
| } |
| |
| Address = Index; |
| MemNSetBitFieldNb (NBPtr, BFDctAddlOffsetReg, Address); |
| Value = MemNGetBitFieldNb (NBPtr, BFDctAddlDataReg); |
| |
| if (IsSet) { |
| if (TrnDly == AccessPhRecDly) { |
| Value = NBPtr->DctCachePtr->PhRecReg[Index & 0x03]; |
| } |
| |
| Value = ((UINT32)Field << Offset) | (Value & (~((UINT32) ((TrnDly == AccessRcvEnDly) ? 0x1FF : 0xFF) << Offset))); |
| MemNSetBitFieldNb (NBPtr, BFDctAddlDataReg, Value); |
| Address |= DCT_ACCESS_WRITE; |
| MemNSetBitFieldNb (NBPtr, BFDctAddlOffsetReg, Address); |
| |
| if (TrnDly == AccessPhRecDly) { |
| NBPtr->DctCachePtr->PhRecReg[Index & 0x03] = Value; |
| } |
| // Gross WrDatDly and WrDqsDly cannot be larger than 4 |
| ASSERT (((TrnDly == AccessWrDatDly) || (TrnDly == AccessWrDqsDly)) ? (Field < 0xA0) : TRUE); |
| } else { |
| Value = (Value >> Offset) & (UINT32) ((TrnDly == AccessRcvEnDly) ? 0x1FF : 0xFF); |
| } |
| |
| return Value; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function initializes the training pattern. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| * @return AGESA_STATUS - Result |
| * AGESA_SUCCESS - Training pattern is ready to use |
| * AGESA_ERROR - Unable to initialize the pattern. |
| */ |
| |
| AGESA_STATUS |
| MemNTrainingPatternInitNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| MEM_TECH_BLOCK *TechPtr; |
| ALLOCATE_HEAP_PARAMS AllocHeapParams; |
| TRAIN_PATTERN TrainPattern; |
| AGESA_STATUS Status; |
| |
| TechPtr = NBPtr->TechPtr; |
| TrainPattern = 0; |
| // |
| // Check the training type |
| // |
| if (TechPtr->TrainingType == TRN_DQS_POSITION) { |
| // |
| // DQS Position Training |
| // |
| if (NBPtr->PosTrnPattern == POS_PATTERN_256B) { |
| // |
| // 256 Bit pattern |
| // |
| if (NBPtr->MCTPtr->Status[Sb128bitmode]) { |
| TrainPattern = TestPatternJD256B; |
| TechPtr->PatternLength = 64; |
| } else { |
| TrainPattern = TestPatternJD256A; |
| TechPtr->PatternLength = 32; |
| } |
| } else { |
| // |
| // 72 bit pattern will be used if PosTrnPattern is not specified |
| // |
| if (NBPtr->MCTPtr->Status[Sb128bitmode]) { |
| TrainPattern = TestPatternJD1B; |
| TechPtr->PatternLength = 18; |
| } else { |
| TrainPattern = TestPatternJD1A; |
| TechPtr->PatternLength = 9; |
| } |
| } |
| } else if (TechPtr->TrainingType == TRN_MAX_READ_LATENCY) { |
| // |
| // Max Read Latency Training |
| // |
| TrainPattern = TestPatternML; |
| TechPtr->PatternLength = (NBPtr->MCTPtr->Status[Sb128bitmode]) ? 6 : 3; |
| } else { |
| // |
| // Error - TechPtr->Training Type must be set to one of the types handled in this function |
| // |
| ASSERT (FALSE); |
| } |
| // |
| // Allocate training buffer |
| // |
| AllocHeapParams.RequestedBufferSize = (TechPtr->PatternLength * 64 * 2) + 16; |
| AllocHeapParams.BufferHandle = AMD_MEM_TRAIN_BUFFER_HANDLE; |
| AllocHeapParams.Persist = HEAP_LOCAL_CACHE; |
| Status = HeapAllocateBuffer (&AllocHeapParams, &NBPtr->MemPtr->StdHeader); |
| ASSERT (Status == AGESA_SUCCESS); |
| if (Status != AGESA_SUCCESS) { |
| return Status; |
| } |
| TechPtr->PatternBufPtr = AllocHeapParams.BufferPtr; |
| AlignPointerTo16Byte (&TechPtr->PatternBufPtr); |
| TechPtr->TestBufPtr = TechPtr->PatternBufPtr + (TechPtr->PatternLength * 64); |
| |
| // Prepare training pattern |
| MemUFillTrainPattern (TrainPattern, TechPtr->PatternBufPtr, TechPtr->PatternLength * 64); |
| |
| return Status; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function determined the settings for the Reliable Read/Write engine |
| * for each specific type of training |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] *OptParam - Pointer to an Enum of TRAINING_TYPE |
| * |
| * @return TRUE |
| */ |
| |
| BOOLEAN |
| MemNSetupHwTrainingEngineUnb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN VOID *OptParam |
| ) |
| { |
| TRAINING_TYPE TrnType; |
| RRW_SETTINGS *Rrw; |
| |
| TrnType = *(TRAINING_TYPE*) OptParam; |
| Rrw = &NBPtr->RrwSettings; |
| // |
| // Common Settings |
| // |
| Rrw->TgtBankAddressA = CPG_BANK_ADDRESS_A; |
| Rrw->TgtRowAddressA = CPG_ROW_ADDRESS_A; |
| Rrw->TgtColAddressA = CPG_COL_ADDRESS_A; |
| Rrw->TgtBankAddressB = CPG_BANK_ADDRESS_B; |
| Rrw->TgtRowAddressB = CPG_ROW_ADDRESS_B; |
| Rrw->TgtColAddressB = CPG_COL_ADDRESS_B; |
| Rrw->CompareMaskHigh = CPG_COMPARE_MASK_HI; |
| Rrw->CompareMaskLow = CPG_COMPARE_MASK_LOW; |
| Rrw->CompareMaskEcc = CPG_COMPARE_MASK_ECC; |
| |
| switch (TrnType) { |
| case TRN_RCVR_ENABLE: |
| // |
| // Receiver Enable Training |
| // |
| NBPtr->TechPtr->PatternLength = 192; |
| break; |
| case TRN_MAX_READ_LATENCY: |
| // |
| // Max Read Latency Training |
| // |
| Rrw->CmdTgt = CMD_TGT_A; |
| NBPtr->TechPtr->PatternLength = 32; |
| Rrw->DataPrbsSeed = PRBS_SEED_32; |
| break; |
| case TRN_DQS_POSITION: |
| // |
| // Read/Write DQS Position training |
| // |
| Rrw->CmdTgt = CMD_TGT_AB; |
| NBPtr->TechPtr->PatternLength = 256; |
| Rrw->DataPrbsSeed = PRBS_SEED_256; |
| break; |
| default: |
| ASSERT (FALSE); |
| } |
| return TRUE; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function finalizes the training pattern. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in] Index - Index of Write Data Delay Value |
| * @param[in,out] *Value - Write Data Delay Value |
| * @return BOOLEAN - TRUE - Use the value returned. |
| * FALSE - No more values in table. |
| */ |
| |
| BOOLEAN |
| MemNGetApproximateWriteDatDelayNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN UINT8 Index, |
| IN OUT UINT8 *Value |
| ) |
| { |
| CONST UINT8 WriteDatDelayValue[] = {0x10, 0x4, 0x8, 0xC, 0x14, 0x18, 0x1C, 0x1F}; |
| if (Index < GET_SIZE_OF (WriteDatDelayValue)) { |
| *Value = WriteDatDelayValue[Index]; |
| return TRUE; |
| } |
| return FALSE; |
| } |
| |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function finalizes the training pattern. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| * @return AGESA_STATUS - Result |
| * AGESA_SUCCESS - Training pattern has been finalized. |
| * AGESA_ERROR - Unable to initialize the pattern. |
| */ |
| |
| AGESA_STATUS |
| MemNTrainingPatternFinalizeNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| AGESA_STATUS Status; |
| // |
| // Deallocate training buffer |
| // |
| Status = HeapDeallocateBuffer (AMD_MEM_TRAIN_BUFFER_HANDLE, &NBPtr->MemPtr->StdHeader); |
| ASSERT (Status == AGESA_SUCCESS); |
| return Status; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function returns the number of chipselects per channel. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| * @return |
| */ |
| |
| UINT8 |
| MemNCSPerChannelNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| return MAX_CS_PER_CHANNEL; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function returns the number of Chipselects controlled by each set |
| * of Delay registers under current conditions. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| * @return |
| */ |
| |
| UINT8 |
| MemNCSPerDelayNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| return MAX_CS_PER_DELAY; |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function returns the minimum data eye width in 32nds of a UI for |
| * the type of data eye(Rd/Wr) that is being trained. This value will |
| * be the minimum number of consecutive delays that yield valid data. |
| * Uses TechPtr->Direction to determine read or write. |
| * |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| * @return |
| */ |
| |
| UINT8 |
| MemNMinDataEyeWidthNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| if (NBPtr->TechPtr->Direction == DQS_READ_DIR) { |
| return MIN_RD_DATAEYE_WIDTH_NB; |
| } else { |
| return MIN_WR_DATAEYE_WIDTH_NB; |
| } |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * This function programs the phy registers according to the desired phy VDDIO voltage level |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNPhyVoltageLevelNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| BIT_FIELD_NAME BitField; |
| UINT16 Value; |
| |
| Value = (UINT16) NBPtr->RefPtr->DDR3Voltage << 3; |
| |
| for (BitField = BFDataRxVioLvl; BitField <= BFCmpVioLvl; BitField++) { |
| if (BitField == BFCmpVioLvl) { |
| Value <<= (14 - 3); |
| } |
| MemNBrdcstSetNb (NBPtr, BitField, Value); |
| } |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function adjusts Avg PRE value of Phy fence training according to specific CPU family. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in,out] *Value16 - Pointer to the value that we want to adjust |
| * |
| */ |
| VOID |
| MemNPFenceAdjustUnb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN OUT UINT16 *Value16 |
| ) |
| { |
| *Value16 += 2; //for LN,ON,and OR, the Avg PRE value is subtracted by 6 only. |
| } |
| |
| /* -----------------------------------------------------------------------------*/ |
| /** |
| * |
| * |
| * This function initializes the DDR phy compensation logic |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * |
| */ |
| |
| VOID |
| MemNInitPhyCompClientNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr |
| ) |
| { |
| // Slew rate table array [x][y][z] |
| // array[0]: slew rate for VDDIO 1.5V |
| // array[1]: slew rate for VDDIO 1.35V |
| // array[x][y]: slew rate for a certain frequency |
| // array[x][y][0]: frequency mask for current entry |
| CONST STATIC UINT16 TxPrePNDataDqs[2][3][5] = { |
| {{ (UINT16) DDR800, 0x924, 0x924, 0x924, 0x924}, |
| { (UINT16) (DDR1066 + DDR1333), 0xFF6, 0xFF6, 0xFF6, 0xFF6}, |
| { (UINT16) (DDR1600 + DDR1866), 0xFF6, 0xFF6, 0xFF6, 0xFF6}}, |
| {{ (UINT16) DDR800, 0xFF6, 0xB6D, 0xB6D, 0x924}, |
| { (UINT16) (DDR1066 + DDR1333), 0xFF6, 0xFF6, 0xFF6, 0xFF6}, |
| { (UINT16) (DDR1600 + DDR1866), 0xFF6, 0xFF6, 0xFF6, 0xFF6}} |
| }; |
| CONST STATIC UINT16 TxPrePNCmdAddr[2][3][5] = { |
| {{ (UINT16) DDR800, 0x492, 0x492, 0x492, 0x492}, |
| { (UINT16) (DDR1066 + DDR1333), 0x6DB, 0x6DB, 0x6DB, 0x6DB}, |
| { (UINT16) (DDR1600 + DDR1866), 0xB6D, 0xB6D, 0xB6D, 0xB6D}}, |
| {{ (UINT16) DDR800, 0x492, 0x492, 0x492, 0x492}, |
| { (UINT16) (DDR1066 + DDR1333), 0x924, 0x6DB, 0x6DB, 0x6DB}, |
| { (UINT16) (DDR1600 + DDR1866), 0xB6D, 0xB6D, 0x924, 0x924}} |
| }; |
| CONST STATIC UINT16 TxPrePNClock[2][3][5] = { |
| {{ (UINT16) DDR800, 0x924, 0x924, 0x924, 0x924}, |
| { (UINT16) (DDR1066 + DDR1333), 0xFF6, 0xFF6, 0xFF6, 0xB6D}, |
| { (UINT16) (DDR1600 + DDR1866), 0xFF6, 0xFF6, 0xFF6, 0xFF6}}, |
| {{ (UINT16) DDR800, 0xDAD, 0xDAD, 0x924, 0x924}, |
| { (UINT16) (DDR1066 + DDR1333), 0xFF6, 0xFF6, 0xFF6, 0xDAD}, |
| { (UINT16) (DDR1600 + DDR1866), 0xFF6, 0xFF6, 0xFF6, 0xDAD}} |
| }; |
| |
| CONST PHY_COMP_INIT_CLIENTNB PhyCompInitBitField[] = { |
| // 3. Program TxPreP/TxPreN for Data and DQS according toTable 14 if VDDIO is 1.5V or Table 15 if 1.35V. |
| // A. Program D18F2x[1,0]9C_x0D0F_0[F,7:0]0[A,6]={0000b, TxPreP, TxPreN}. |
| // B. Program D18F2x[1,0]9C_x0D0F_0[F,7:0]02={1000b, TxPreP, TxPreN}. |
| {BFDqsDrvStren, BFDataByteTxPreDriverCal2Pad1, BFDataByteTxPreDriverCal2Pad1, 0, TxPrePNDataDqs}, |
| {BFDataDrvStren, BFDataByteTxPreDriverCal2Pad2, BFDataByteTxPreDriverCal2Pad2, 0, TxPrePNDataDqs}, |
| {BFDataDrvStren, BFDataByteTxPreDriverCal, BFDataByteTxPreDriverCal, 8, TxPrePNDataDqs}, |
| // 4. Program TxPreP/TxPreN for Cmd/Addr according toTable 16 if VDDIO is 1.5V or Table 17 if 1.35V. |
| // A. Program D18F2x[1,0]9C_x0D0F_[C,8][1:0][12,0E,0A,06]={0000b, TxPreP, TxPreN}. |
| // B. Program D18F2x[1,0]9C_x0D0F_[C,8][1:0]02={1000b, TxPreP, TxPreN}. |
| {BFCsOdtDrvStren, BFCmdAddr0TxPreDriverCal2Pad1, BFCmdAddr0TxPreDriverCal2Pad2, 0, TxPrePNCmdAddr}, |
| {BFAddrCmdDrvStren, BFCmdAddr1TxPreDriverCal2Pad1, BFAddrTxPreDriverCal2Pad4, 0, TxPrePNCmdAddr}, |
| {BFCsOdtDrvStren, BFCmdAddr0TxPreDriverCalPad0, BFCmdAddr0TxPreDriverCalPad0, 8, TxPrePNCmdAddr}, |
| {BFCkeDrvStren, BFAddrTxPreDriverCalPad0, BFAddrTxPreDriverCalPad0, 8, TxPrePNCmdAddr}, |
| {BFAddrCmdDrvStren, BFCmdAddr1TxPreDriverCalPad0, BFCmdAddr1TxPreDriverCalPad0, 8, TxPrePNCmdAddr}, |
| // 5. Program TxPreP/TxPreN for Clock according toTable 18 if VDDIO is 1.5V or Table 19 if 1.35V. |
| // A. Program D18F2x[1,0]9C_x0D0F_2[1:0]02={1000b, TxPreP, TxPreN}. |
| {BFClkDrvStren, BFClock0TxPreDriverCalPad0, BFClock1TxPreDriverCalPad0, 8, TxPrePNClock} |
| }; |
| |
| BIT_FIELD_NAME CurrentBitField; |
| UINT16 SpeedMask; |
| CONST UINT16 (*TxPrePNArray)[5]; |
| UINT8 Voltage; |
| UINT8 i; |
| UINT8 j; |
| UINT8 k; |
| UINT8 Dct; |
| |
| Dct = NBPtr->Dct; |
| NBPtr->SwitchDCT (NBPtr, 0); |
| // 1. Program D18F2x[1,0]9C_x0D0F_E003[DisAutoComp, DisablePreDriverCal] = {1b, 1b}. |
| MemNSetBitFieldNb (NBPtr, BFDisablePredriverCal, 0x6000); |
| NBPtr->SwitchDCT (NBPtr, Dct); |
| |
| SpeedMask = (UINT16) 1 << (NBPtr->DCTPtr->Timings.Speed / 66); |
| Voltage = (UINT8) NBPtr->RefPtr->DDR3Voltage; |
| |
| for (j = 0; j < GET_SIZE_OF (PhyCompInitBitField); j ++) { |
| i = (UINT8) MemNGetBitFieldNb (NBPtr, PhyCompInitBitField[j].IndexBitField); |
| TxPrePNArray = PhyCompInitBitField[j].TxPrePN[Voltage]; |
| for (k = 0; k < 3; k ++) { |
| if ((TxPrePNArray[k][0] & SpeedMask) != 0) { |
| for (CurrentBitField = PhyCompInitBitField[j].StartTargetBitField; CurrentBitField <= PhyCompInitBitField[j].EndTargetBitField; CurrentBitField ++) { |
| MemNSetBitFieldNb (NBPtr, CurrentBitField, ((PhyCompInitBitField[j].ExtraValue << 12) | TxPrePNArray[k][i + 1])); |
| } |
| break; |
| } |
| } |
| ASSERT (k < 3); |
| } |
| |
| NBPtr->FamilySpecificHook[ForceAutoComp] (NBPtr, NBPtr); |
| } |
| |
| /*----------------------------------------------------------------------------- |
| * |
| * |
| * This function re-enable phy compensation. |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in,out] OptParam - Optional parameter |
| * |
| * @return TRUE |
| * ---------------------------------------------------------------------------- |
| */ |
| BOOLEAN |
| MemNReEnablePhyCompNb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN OUT VOID *OptParam |
| ) |
| { |
| UINT8 Dct; |
| |
| Dct = NBPtr->Dct; |
| |
| NBPtr->SwitchDCT (NBPtr, 0); |
| // Clear DisableCal and set DisablePredriverCal |
| MemNSetBitFieldNb (NBPtr, BFDisablePredriverCal, 0x2000); |
| NBPtr->SwitchDCT (NBPtr, Dct); |
| |
| return TRUE; |
| } |
| |
| /*----------------------------------------------------------------------------- |
| * |
| * |
| * This function calculates the value of WrDqDqsEarly and programs it into |
| * the DCT and adds it to the WrDqsGrossDelay of each byte lane on each |
| * DIMM of the channel. |
| * |
| * |
| * @param[in,out] *NBPtr - Pointer to the MEM_NB_BLOCK |
| * @param[in,out] OptParam - Optional parameter |
| * |
| * @return TRUE |
| * ---------------------------------------------------------------------------- |
| */ |
| BOOLEAN |
| MemNCalcWrDqDqsEarlyUnb ( |
| IN OUT MEM_NB_BLOCK *NBPtr, |
| IN OUT VOID *OptParam |
| ) |
| { |
| MEM_TECH_BLOCK *TechPtr; |
| DCT_STRUCT *DCTPtr; |
| CH_DEF_STRUCT *ChannelPtr; |
| UINT8 Dimm; |
| UINT8 ByteLane; |
| UINT8 *WrDqsDlysPtr; |
| UINT8 WrDqDqsEarly; |
| |
| ASSERT ((NBPtr->IsSupported[WLSeedAdjust]) && (NBPtr->IsSupported[WLNegativeDelay])); |
| |
| TechPtr = NBPtr->TechPtr; |
| ChannelPtr = NBPtr->ChannelPtr; |
| DCTPtr = NBPtr->DCTPtr; |
| |
| ASSERT (NBPtr != NULL); |
| ASSERT (ChannelPtr != NULL); |
| ASSERT (DCTPtr != NULL); |
| // |
| // For each DIMM: |
| // - The Critical Gross Delay (CGD) is the minimum GrossDly of all byte lanes and all DIMMs. |
| // - If (CGD < 0) Then |
| // - D18F2xA8_dct[1:0][WrDqDqsEarly] = ABS(CGD) |
| // - WrDqsGrossDly = GrossDly + WrDqDqsEarly |
| // - Else |
| // - D18F2xA8_dct[1:0][WrDqDqsEarly] = 0. |
| // - WrDqsGrossDly = GrossDly |
| // |
| WrDqDqsEarly = 0; |
| if (TechPtr->WLCriticalDelay < 0) { |
| IDS_HDT_CONSOLE(MEM_FLOW, "\t\tCalculating WrDqDqsEarly, adjusting WrDqs.\n"); |
| // We've saved the entire negative delay value, so take the ABS and convert to GrossDly. |
| WrDqDqsEarly = (UINT8) (0x00FF &((((ABS (TechPtr->WLCriticalDelay)) + 0x1F) / 0x20))); |
| // |
| // Loop through All WrDqsDlys on all DIMMs |
| // |
| for (Dimm = 0; Dimm < MAX_DIMMS_PER_CHANNEL; Dimm++) { |
| if ((DCTPtr->Timings.CsEnabled & ((UINT16)3 << (Dimm << 1))) != 0) { |
| IDS_HDT_CONSOLE(MEM_FLOW, "\t\t\tDimm %x:",Dimm); |
| WrDqsDlysPtr = &(ChannelPtr->WrDqsDlys[(Dimm * TechPtr->DlyTableWidth ())]); |
| for (ByteLane = 0; ByteLane < TechPtr->DlyTableWidth (); ByteLane++) { |
| WrDqsDlysPtr[ByteLane] += (WrDqDqsEarly << 5); |
| NBPtr->SetTrainDly (NBPtr, AccessWrDqsDly, DIMM_BYTE_ACCESS (Dimm, ByteLane), WrDqsDlysPtr[ByteLane]); |
| IDS_HDT_CONSOLE(MEM_FLOW, " %02x",WrDqsDlysPtr[ByteLane]); |
| } |
| IDS_HDT_CONSOLE(MEM_FLOW, "\n"); |
| } |
| } |
| } |
| MemNSetBitFieldNb (NBPtr, BFWrDqDqsEarly, WrDqDqsEarly); |
| IDS_HDT_CONSOLE(MEM_FLOW, "\t\tWrDqDqsEarly : %02x\n",WrDqDqsEarly); |
| return TRUE; |
| } |