| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <device/device.h> |
| #include <amdblocks/agesawrapper.h> |
| #include <amdblocks/amd_pci_util.h> |
| #include <gpio.h> |
| #include <soc/acpi.h> |
| #include <soc/pci_devs.h> |
| #include <soc/southbridge.h> |
| |
| #include "gpio.h" |
| |
| /* The IRQ mapping in fch_irq_map ends up getting written to the indirect address space that is |
| accessed via I/O ports 0xc00/0xc01. */ |
| static const struct fch_irq_routing fch_irq_map[] = { |
| { PIRQ_A, 3, 16 }, |
| { PIRQ_B, 4, 17 }, |
| { PIRQ_C, 5, 18 }, |
| { PIRQ_D, 7, 19 }, |
| { PIRQ_E, 11, 20 }, |
| { PIRQ_F, 10, 21 }, |
| { PIRQ_G, PIRQ_NC, 22 }, |
| { PIRQ_H, PIRQ_NC, 23 }, |
| { PIRQ_SCI, ACPI_SCI_IRQ, ACPI_SCI_IRQ }, |
| { PIRQ_SMBUS, PIRQ_NC, PIRQ_NC }, |
| { PIRQ_HDA, 3, 16 }, |
| { PIRQ_SD, PIRQ_NC, 16 }, |
| { PIRQ_SDIO, PIRQ_NC, PIRQ_NC }, |
| { PIRQ_EHCI, 5, 18 }, |
| { PIRQ_XHCI, 4, 18 }, |
| { PIRQ_SATA, PIRQ_NC, 19 }, |
| { PIRQ_GPIO, 7, 7 }, |
| { PIRQ_I2C0, 3, 3 }, |
| { PIRQ_I2C1, 15, 15 }, |
| { PIRQ_I2C2, 6, 6 }, |
| { PIRQ_I2C3, 14, 14 }, |
| { PIRQ_UART0, 10, 10 }, |
| { PIRQ_UART1, 11, 11 }, |
| |
| /* The MISC registers are not interrupt numbers */ |
| { PIRQ_MISC, 0xfa, 0x00 }, |
| { PIRQ_MISC0, 0xf1, 0x00 }, |
| { PIRQ_MISC1, 0x00, 0x00 }, |
| { PIRQ_MISC2, 0x00, 0x00 }, |
| }; |
| |
| const struct fch_irq_routing *mb_get_fch_irq_mapping(size_t *length) |
| { |
| *length = ARRAY_SIZE(fch_irq_map); |
| return fch_irq_map; |
| } |
| |
| /* |
| * This table defines the index into the picr/intr_data tables for each |
| * device. Any enabled device and slot that uses hardware interrupts should |
| * have an entry in this table to define its index into the FCH PCI_INTR |
| * register 0xC00/0xC01. This index will define the interrupt that it should |
| * use. Putting PIRQ_A into the PIN A index for a device will tell that |
| * device to use PIC IRQ 10 if it uses PIN A for its hardware INT. |
| */ |
| static const struct pirq_struct mainboard_pirq_data[] = { |
| { GFX_DEVFN, { PIRQ_A, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { HDA0_DEVFN, { PIRQ_NC, PIRQ_HDA, PIRQ_NC, PIRQ_NC } }, |
| { PCIE0_DEVFN, { PIRQ_A, PIRQ_B, PIRQ_C, PIRQ_D } }, |
| { PCIE1_DEVFN, { PIRQ_B, PIRQ_C, PIRQ_D, PIRQ_A } }, |
| { PCIE2_DEVFN, { PIRQ_C, PIRQ_D, PIRQ_A, PIRQ_B } }, |
| { PCIE3_DEVFN, { PIRQ_D, PIRQ_A, PIRQ_B, PIRQ_C } }, |
| { PCIE4_DEVFN, { PIRQ_A, PIRQ_B, PIRQ_C, PIRQ_D } }, |
| { PSP_DEVFN, { PIRQ_A, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { HDA1_DEVFN, { PIRQ_HDA, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { SD_DEVFN, { PIRQ_SD, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { SMBUS_DEVFN, { PIRQ_SMBUS, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { SATA_DEVFN, { PIRQ_SATA, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { EHCI1_DEVFN, { PIRQ_EHCI, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| { XHCI_DEVFN, { PIRQ_XHCI, PIRQ_NC, PIRQ_NC, PIRQ_NC } }, |
| }; |
| |
| /* PIRQ Setup */ |
| static void pirq_setup(void) |
| { |
| pirq_data_ptr = mainboard_pirq_data; |
| pirq_data_size = ARRAY_SIZE(mainboard_pirq_data); |
| } |
| |
| static void mainboard_init(void *chip_info) |
| { |
| size_t num_gpios; |
| const struct soc_amd_gpio *gpios; |
| gpios = gpio_table(&num_gpios); |
| gpio_configure_pads(gpios, num_gpios); |
| } |
| |
| /************************************************* |
| * enable the dedicated function in pademelon board. |
| *************************************************/ |
| static void mainboard_enable(struct device *dev) |
| { |
| /* Initialize the PIRQ data structures for consumption */ |
| pirq_setup(); |
| } |
| |
| struct chip_operations mainboard_ops = { |
| .init = mainboard_init, |
| .enable_dev = mainboard_enable, |
| }; |