| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007 AMD |
| * Written by Yinghai Lu <yinghailu@amd.com> for AMD. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #define FAM10_SCAN_PCI_BUS 0 |
| #define FAM10_ALLOCATE_IO_RANGE 1 |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <device/pci_def.h> |
| #include <device/pci_ids.h> |
| #include <arch/io.h> |
| #include <device/pnp_def.h> |
| #include <arch/romcc_io.h> |
| #include <cpu/x86/lapic.h> |
| #include <console/console.h> |
| #include <usbdebug.h> |
| #include <lib.h> |
| #include <spd.h> |
| |
| #include <cpu/amd/model_10xxx_rev.h> |
| |
| #include "southbridge/nvidia/mcp55/mcp55_early_smbus.c" |
| #include "northbridge/amd/amdfam10/raminit.h" |
| #include "northbridge/amd/amdfam10/amdfam10.h" |
| #include "cpu/amd/model_fxx/apic_timer.c" |
| #include "lib/delay.c" |
| |
| #include "cpu/x86/lapic/boot_cpu.c" |
| #include "northbridge/amd/amdfam10/reset_test.c" |
| #include "superio/winbond/w83627ehg/w83627ehg_early_serial.c" |
| |
| #include "cpu/x86/bist.h" |
| |
| #include "northbridge/amd/amdfam10/debug.c" |
| |
| #include "cpu/x86/mtrr/earlymtrr.c" |
| |
| #include "northbridge/amd/amdfam10/setup_resource_map.c" |
| |
| #define SERIAL_DEV PNP_DEV(0x2e, W83627EHG_SP1) |
| |
| #include "southbridge/nvidia/mcp55/mcp55_early_ctrl.c" |
| |
| static inline void activate_spd_rom(const struct mem_controller *ctrl) |
| { |
| /* nothing to do */ |
| } |
| |
| static inline int spd_read_byte(unsigned device, unsigned address) |
| { |
| return smbus_read_byte(device, address); |
| } |
| |
| #include "northbridge/amd/amdfam10/amdfam10.h" |
| |
| #include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c" |
| #include "northbridge/amd/amdfam10/amdfam10_pci.c" |
| |
| #include "resourcemap.c" |
| |
| #include "cpu/amd/quadcore/quadcore.c" |
| |
| #define MCP55_MB_SETUP \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+37, 0x00, 0x44,/* GPIO38 PCI_REQ3 */ \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+38, 0x00, 0x44,/* GPIO39 PCI_GNT3 */ \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+39, 0x00, 0x44,/* GPIO40 PCI_GNT2 */ \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+40, 0x00, 0x44,/* GPIO41 PCI_REQ2 */ \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+59, 0x00, 0x60,/* GPIP60 FANCTL0 */ \ |
| RES_PORT_IO_8, SYSCTRL_IO_BASE + 0xc0+60, 0x00, 0x60,/* GPIO61 FANCTL1 */ |
| |
| #include "southbridge/nvidia/mcp55/mcp55_early_setup_ss.h" |
| #include "southbridge/nvidia/mcp55/mcp55_early_setup_car.c" |
| |
| |
| |
| #include "cpu/amd/car/post_cache_as_ram.c" |
| |
| #include "cpu/amd/microcode/microcode.c" |
| #include "cpu/amd/model_10xxx/update_microcode.c" |
| #include "cpu/amd/model_10xxx/init_cpus.c" |
| |
| |
| #include "southbridge/nvidia/mcp55/mcp55_enable_rom.c" |
| #include "northbridge/amd/amdfam10/early_ht.c" |
| |
| static void sio_setup(void) |
| { |
| u32 dword; |
| u8 byte; |
| |
| byte = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0x7b); |
| byte |= 0x20; |
| pci_write_config8(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0x7b, byte); |
| |
| dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa0); |
| dword |= (1<<0); |
| pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa0, dword); |
| } |
| |
| static const u8 spd_addr[] = { |
| //first node |
| RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, |
| #if CONFIG_MAX_PHYSICAL_CPUS > 1 |
| //second node |
| RC00, DIMM4, DIMM6, 0, 0, DIMM5, DIMM7, 0, 0, |
| #endif |
| }; |
| |
| void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) |
| { |
| struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE); |
| |
| u32 bsp_apicid = 0; |
| u32 val; |
| u8 reg; |
| u32 wants_reset; |
| msr_t msr; |
| |
| if (!cpu_init_detectedx && boot_cpu()) { |
| /* Nothing special needs to be done to find bus 0 */ |
| /* Allow the HT devices to be found */ |
| |
| set_bsp_node_CHtExtNodeCfgEn(); |
| enumerate_ht_chain(); |
| |
| sio_setup(); |
| |
| /* Setup the mcp55 */ |
| mcp55_enable_rom(); |
| } |
| |
| post_code(0x30); |
| |
| if (bist == 0) { |
| bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); |
| } |
| |
| post_code(0x32); |
| |
| pnp_enter_ext_func_mode(SERIAL_DEV); |
| /* We have 24MHz input. */ |
| reg = pnp_read_config(SERIAL_DEV, 0x24); |
| pnp_write_config(SERIAL_DEV, 0x24, (reg & 0xbf)); |
| pnp_exit_ext_func_mode(SERIAL_DEV); |
| |
| w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); |
| uart_init(); |
| console_init(); |
| printk(BIOS_DEBUG, "\n"); |
| |
| /* Halt if there was a built in self test failure */ |
| report_bist_failure(bist); |
| |
| #if CONFIG_USBDEBUG |
| mcp55_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT); |
| early_usbdebug_init(); |
| #endif |
| |
| val = cpuid_eax(1); |
| printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val); |
| printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1); |
| printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid); |
| printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx); |
| |
| /* Setup sysinfo defaults */ |
| set_sysinfo_in_ram(0); |
| |
| update_microcode(val); |
| post_code(0x33); |
| |
| cpuSetAMDMSR(); |
| post_code(0x34); |
| |
| amd_ht_init(sysinfo); |
| post_code(0x35); |
| |
| /* Setup nodes PCI space and start core 0 AP init. */ |
| finalize_node_setup(sysinfo); |
| printk(BIOS_DEBUG, "finalize_node_setup done\n"); |
| |
| /* Setup any mainboard PCI settings etc. */ |
| printk(BIOS_DEBUG, "setup_mb_resource_map begin\n"); |
| setup_mb_resource_map(); |
| printk(BIOS_DEBUG, "setup_mb_resource_map end\n"); |
| post_code(0x36); |
| |
| /* wait for all the APs core0 started by finalize_node_setup. */ |
| /* FIXME: A bunch of cores are going to start output to serial at once. |
| * It would be nice to fixup prink spinlocks for ROM XIP mode. |
| * I think it could be done by putting the spinlock flag in the cache |
| * of the BSP located right after sysinfo. |
| */ |
| wait_all_core0_started(); |
| |
| #if CONFIG_LOGICAL_CPUS==1 |
| /* Core0 on each node is configured. Now setup any additional cores. */ |
| printk(BIOS_DEBUG, "start_other_cores()\n"); |
| start_other_cores(); |
| post_code(0x37); |
| printk(BIOS_DEBUG, "wait_all_other_cores_started()\n"); |
| wait_all_other_cores_started(bsp_apicid); |
| #endif |
| |
| post_code(0x38); |
| |
| #if CONFIG_SET_FIDVID |
| msr = rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo); |
| |
| /* FIXME: The sb fid change may survive the warm reset and only |
| * need to be done once.*/ |
| enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); |
| |
| post_code(0x39); |
| |
| if (!warm_reset_detect(0)) { // BSP is node 0 |
| init_fidvid_bsp(bsp_apicid, sysinfo->nodes); |
| } else { |
| init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0 |
| } |
| |
| post_code(0x3A); |
| |
| /* show final fid and vid */ |
| msr=rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo); |
| #endif |
| init_timer(); /* Need to use TMICT to synconize FID/VID. */ |
| |
| wants_reset = mcp55_early_setup_x(); |
| |
| /* Reset for HT, FIDVID, PLL and errata changes to take affect. */ |
| if (!warm_reset_detect(0)) { |
| print_info("...WARM RESET...\n\n\n"); |
| soft_reset(); |
| die("After soft_reset_x - shouldn't see this message!!!\n"); |
| } |
| |
| if (wants_reset) |
| printk(BIOS_DEBUG, "mcp55_early_setup_x wanted additional reset!\n"); |
| |
| post_code(0x3B); |
| |
| /* It's the time to set ctrl in sysinfo now; */ |
| printk(BIOS_DEBUG, "fill_mem_ctrl()\n"); |
| fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); |
| post_code(0x3D); |
| |
| printk(BIOS_DEBUG, "enable_smbus()\n"); |
| enable_smbus(); |
| |
| post_code(0x40); |
| |
| printk(BIOS_DEBUG, "raminit_amdmct()\n"); |
| raminit_amdmct(sysinfo); |
| post_code(0x41); |
| |
| printk(BIOS_DEBUG, "\n*** Yes, the copy/decompress is taking a while, FIXME!\n"); |
| post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB. |
| post_code(0x43); // Should never see this post code. |
| } |
| |