| # SPDX-License-Identifier: GPL-2.0-or-later |
| fw_config |
| field FP 0 |
| option FP_ABSENT 0 |
| option FP_PRESENT 1 |
| end |
| end |
| |
| chip soc/amd/mendocino |
| |
| # Set DPTC multi-profile common parameters |
| |
| # Refer the spec "FT6 Infrastructure Roadmap"#57316 |
| # Set system_configuration to 4 for 15W |
| register "system_configuration" = "4" |
| register "thermctl_limit_degreeC" = "97" |
| |
| register "stt_control" = "1" |
| register "stt_pcb_sensor_count" = "2" |
| register "stt_alpha_apu" = "0x6666" |
| register "stt_error_coeff" = "0x38" |
| register "stt_error_rate_coefficient" = "0xB44" |
| |
| # These registers are defined in AMD DevHub document #57316. |
| # Normal |
| register "vrm_current_limit_mA" = "28000" |
| register "vrm_maximum_current_limit_mA" = "50000" |
| register "vrm_soc_current_limit_mA" = "10000" |
| # Throttle (e.g., Low/No Battery) |
| register "vrm_current_limit_throttle_mA" = "20000" |
| register "vrm_maximum_current_limit_throttle_mA" = "20000" |
| register "vrm_soc_current_limit_throttle_mA" = "10000" |
| |
| # Set Dynamic DPTC thermal profile Table A (Default) |
| register "fast_ppt_limit_mW" = "30000" |
| register "slow_ppt_limit_mW" = "25000" |
| register "slow_ppt_time_constant_s" = "5" |
| |
| register "stt_min_limit" = "15000" |
| register "stt_m1" = "0x18F" |
| register "stt_m2" = "0x48F" |
| register "stt_c_apu" = "0xECC5" |
| register "stt_skin_temp_apu" = "0x3200" |
| |
| # Set Dynamic DPTC thermal profile confiuration. Table B |
| register "fast_ppt_limit_mW_B" = "15000" |
| register "slow_ppt_limit_mW_B" = "15000" |
| register "slow_ppt_time_constant_s_B" = "5" |
| |
| register "stt_min_limit_B" = "10500" |
| register "stt_m1_B" = "0x18F" |
| register "stt_m2_B" = "0x48F" |
| register "stt_c_apu_B" = "0xECC5" |
| register "stt_skin_temp_apu_B" = "0x3300" |
| |
| # Set Dynamic DPTC thermal profile confiuration. Table C |
| register "fast_ppt_limit_mW_C" = "30000" |
| register "slow_ppt_limit_mW_C" = "25000" |
| register "slow_ppt_time_constant_s_C" = "5" |
| |
| register "stt_min_limit_C" = "15000" |
| register "stt_m1_C" = "0x152" |
| register "stt_m2_C" = "0x4AE" |
| register "stt_c_apu_C" = "0xEE94" |
| register "stt_skin_temp_apu_C" = "0x3200" |
| |
| # Set Dynamic DPTC thermal profile confiuration. Table D |
| register "fast_ppt_limit_mW_D" = "15000" |
| register "slow_ppt_limit_mW_D" = "15000" |
| register "slow_ppt_time_constant_s_D" = "5" |
| |
| register "stt_min_limit_D" = "10500" |
| register "stt_m1_D" = "0x152" |
| register "stt_m2_D" = "0x4AE" |
| register "stt_c_apu_D" = "0xEE94" |
| register "stt_skin_temp_apu_D" = "0x3300" |
| |
| # Set Dynamic DPTC thermal profile confiuration. Table E |
| register "fast_ppt_limit_mW_E" = "24000" |
| register "slow_ppt_limit_mW_E" = "20000" |
| register "slow_ppt_time_constant_s_E" = "5" |
| |
| register "stt_min_limit_E" = "12000" |
| register "stt_m1_E" = "0x18F" |
| register "stt_m2_E" = "0x48F" |
| register "stt_c_apu_E" = "0xECC5" |
| register "stt_skin_temp_apu_E" = "0x2F00" |
| |
| |
| # Set Dynamic DPTC thermal profile confiuration. Table F |
| register "fast_ppt_limit_mW_F" = "12000" |
| register "slow_ppt_limit_mW_F" = "12000" |
| register "slow_ppt_time_constant_s_F" = "5" |
| |
| register "stt_min_limit_F" = "8000" |
| register "stt_m1_F" = "0x18F" |
| register "stt_m2_F" = "0x48F" |
| register "stt_c_apu_F" = "0xECC5" |
| register "stt_skin_temp_apu_F" = "0x3000" |
| |
| register "i2c[0]" = "{ |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_hcnt = 107, |
| .scl_lcnt = 230, |
| .sda_hold = 100 |
| } |
| }" |
| |
| device domain 0 on |
| |
| register "dxio_tx_vboost_enable" = "1" |
| |
| device ref gpp_bridge_1 on |
| # Required so the NVMe gets placed into D3 when entering S0i3. |
| chip drivers/pcie/rtd3/device |
| register "name" = ""NVME"" |
| device pci 00.0 on end |
| end |
| end # eMMC |
| device ref gpp_bridge_2 on |
| # Required so the NVMe gets placed into D3 when entering S0i3. |
| chip drivers/pcie/rtd3/device |
| register "name" = ""NVME"" |
| device pci 00.0 on end |
| end |
| end # NVMe |
| |
| device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A |
| device ref xhci_1 on # XHCI1 controller |
| chip drivers/usb/acpi |
| device ref xhci_1_root_hub on # XHCI1 root hub |
| chip drivers/usb/acpi |
| device ref usb3_port3 on # USB 3.1 port3 |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device usb 3.2 on end |
| end |
| end # USB 3.1 port3 |
| end |
| chip drivers/usb/acpi |
| device ref usb2_port3 on # USB 2 port3 |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device usb 2.2 on end |
| end |
| end # USB 2 port3 |
| end |
| end # XHCI1 root hub |
| end |
| end # XHCI1 controller |
| end # Internal GPP Bridge 0 to Bus A |
| end # domain |
| |
| device ref i2c_0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_40)" |
| register "wake" = "GEVENT_20" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GXTP7863"" |
| register "generic.desc" = ""Goodix Touchpad"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_40)" |
| register "generic.wake" = "GEVENT_20" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| end # I2C0 |
| device ref i2c_1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN900C"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_29)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)" |
| register "generic.enable_delay_ms" = "10" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.reset_delay_ms" = "10" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)" |
| register "generic.stop_delay_ms" = "180" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""MLFS0000"" |
| register "desc" = ""Melfas Touchscreen"" |
| register "detect" = "1" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_29)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)" |
| register "enable_delay_ms" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)" |
| register "reset_delay_ms" = "20" |
| register "reset_off_delay_ms" = "2" |
| register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)" |
| register "stop_off_delay_ms" = "2" |
| register "has_power_resource" = "1" |
| device i2c 34 on end |
| end |
| end # I2C1 |
| device ref i2c_2 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "2" |
| register "probed" = "1" |
| device i2c 2a on end |
| end |
| end # I2C2 |
| |
| device ref uart_1 on |
| chip drivers/uart/acpi |
| register "name" = ""CRFP"" |
| register "desc" = ""Fingerprint Reader"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cros-ec-uart"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_24)" |
| register "wake" = "GEVENT_15" |
| register "uart" = "ACPI_UART_RAW_DEVICE(3000000, 64)" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_12)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_4)" |
| register "enable_delay_ms" = "3" |
| device generic 0 alias fpmcu on |
| probe FP FP_PRESENT |
| end |
| end |
| end # UART1 |
| |
| end # chip soc/amd/mendocino |