| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <console/console.h> |
| #include <device/pci.h> |
| #include <cpu/x86/lapic.h> |
| #include <cpu/x86/mp.h> |
| #include <cpu/x86/msr.h> |
| #include <cpu/intel/smm_reloc.h> |
| #include <cpu/intel/turbo.h> |
| #include <intelblocks/cpulib.h> |
| #include <intelblocks/mp_init.h> |
| #include <soc/cpu.h> |
| #include <soc/msr.h> |
| #include <soc/pci_devs.h> |
| #include <soc/systemagent.h> |
| #include <cpu/x86/mtrr.h> |
| #include <cpu/intel/microcode.h> |
| #include <cpu/intel/common/common.h> |
| #include <types.h> |
| |
| #include "chip.h" |
| |
| static void soc_fsp_load(void) |
| { |
| fsps_load(); |
| } |
| |
| static void configure_misc(void) |
| { |
| msr_t msr; |
| |
| config_t *conf = config_of_soc(); |
| |
| msr = rdmsr(IA32_MISC_ENABLE); |
| msr.lo |= (1 << 0); /* Fast String enable */ |
| msr.lo |= (1 << 3); /* TM1/TM2/EMTTM enable */ |
| wrmsr(IA32_MISC_ENABLE, msr); |
| |
| /* Set EIST status */ |
| cpu_set_eist(conf->eist_enable); |
| |
| /* Disable Thermal interrupts */ |
| msr.lo = 0; |
| msr.hi = 0; |
| wrmsr(IA32_THERM_INTERRUPT, msr); |
| |
| /* Enable package critical interrupt only */ |
| msr.lo = 1 << 4; |
| msr.hi = 0; |
| wrmsr(IA32_PACKAGE_THERM_INTERRUPT, msr); |
| |
| /* Enable PROCHOT */ |
| msr = rdmsr(MSR_POWER_CTL); |
| msr.lo |= (1 << 0); /* Enable Bi-directional PROCHOT as an input */ |
| msr.lo |= (1 << 18); /* Enable Energy/Performance Bias control */ |
| msr.lo |= (1 << 23); /* Lock it */ |
| wrmsr(MSR_POWER_CTL, msr); |
| } |
| |
| static void configure_c_states(const config_t *const cfg) |
| { |
| msr_t msr; |
| |
| msr = rdmsr(MSR_PKG_CST_CONFIG_CONTROL); |
| if (cfg->max_package_c_state && (msr.lo & 0xf) >= cfg->max_package_c_state) { |
| msr.lo = (msr.lo & ~0xf) | ((cfg->max_package_c_state - 1) & 0xf); |
| } |
| msr.lo |= CST_CFG_LOCK_MASK; |
| wrmsr(MSR_PKG_CST_CONFIG_CONTROL, msr); |
| |
| /* C-state Interrupt Response Latency Control 0 - package C3 latency */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_0_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_0, msr); |
| |
| /* C-state Interrupt Response Latency Control 1 - package C6/C7 short */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_1_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_1, msr); |
| |
| /* C-state Interrupt Response Latency Control 2 - package C6/C7 long */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_2_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_2, msr); |
| |
| /* C-state Interrupt Response Latency Control 3 - package C8 */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_3_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_3, msr); |
| |
| /* C-state Interrupt Response Latency Control 4 - package C9 */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_4_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_4, msr); |
| |
| /* C-state Interrupt Response Latency Control 5 - package C10 */ |
| msr.hi = 0; |
| msr.lo = IRTL_VALID | IRTL_1024_NS | C_STATE_LATENCY_CONTROL_5_LIMIT; |
| wrmsr(MSR_C_STATE_LATENCY_CONTROL_5, msr); |
| } |
| |
| /* All CPUs including BSP will run the following function. */ |
| void soc_core_init(struct device *cpu) |
| { |
| config_t *cfg = config_of_soc(); |
| |
| /* Clear out pending MCEs */ |
| /* TODO(adurbin): This should only be done on a cold boot. Also, some |
| * of these banks are core vs package scope. For now every CPU clears |
| * every bank. */ |
| mca_configure(); |
| |
| /* Enable the local CPU apics */ |
| enable_lapic_tpr(); |
| setup_lapic(); |
| |
| /* Configure c-state interrupt response time */ |
| configure_c_states(cfg); |
| |
| /* Configure Enhanced SpeedStep and Thermal Sensors */ |
| configure_misc(); |
| |
| set_aesni_lock(); |
| |
| enable_pm_timer_emulation(); |
| |
| /* Enable Direct Cache Access */ |
| configure_dca_cap(); |
| |
| /* Set energy policy */ |
| set_energy_perf_bias(ENERGY_POLICY_NORMAL); |
| |
| if (cfg->cpu_turbo_disable) |
| disable_turbo(); |
| else |
| enable_turbo(); |
| |
| /* Enable Vmx */ |
| set_vmx_and_lock(); |
| } |
| |
| static void per_cpu_smm_trigger(void) |
| { |
| /* Relocate the SMM handler. */ |
| smm_relocate(); |
| } |
| |
| void smm_lock(void) |
| { |
| struct device *sa_dev = pcidev_path_on_root(SA_DEVFN_ROOT); |
| /* |
| * LOCK the SMM memory window and enable normal SMM. |
| * After running this function, only a full reset can |
| * make the SMM registers writable again. |
| */ |
| printk(BIOS_DEBUG, "Locking SMM.\n"); |
| pci_write_config8(sa_dev, SMRAM, D_LCK | G_SMRAME | C_BASE_SEG); |
| } |
| |
| static void post_mp_init(void) |
| { |
| /* Set Max Ratio */ |
| cpu_set_max_ratio(); |
| |
| /* |
| * Now that all APs have been relocated as well as the BSP let SMIs |
| * start flowing. |
| */ |
| global_smi_enable_no_pwrbtn(); |
| |
| /* Lock down the SMRAM space. */ |
| smm_lock(); |
| } |
| |
| static const struct mp_ops mp_ops = { |
| /* |
| * Skip Pre MP init MTRR programming as MTRRs are mirrored from BSP, |
| * that are set prior to ramstage. |
| * Real MTRRs programming are being done after resource allocation. |
| */ |
| .pre_mp_init = soc_fsp_load, |
| .get_cpu_count = get_cpu_count, |
| .get_smm_info = smm_info, |
| .get_microcode_info = get_microcode_info, |
| .pre_mp_smm_init = smm_initialize, |
| .per_cpu_smm_trigger = per_cpu_smm_trigger, |
| .relocation_handler = smm_relocation_handler, |
| .post_mp_init = post_mp_init, |
| }; |
| |
| void soc_init_cpus(struct bus *cpu_bus) |
| { |
| if (mp_init_with_smm(cpu_bus, &mp_ops) != CB_SUCCESS) |
| printk(BIOS_ERR, "MP initialization failure.\n"); |
| |
| /* Thermal throttle activation offset */ |
| configure_tcc_thermal_target(); |
| } |
| |
| int soc_skip_ucode_update(u32 current_patch_id, u32 new_patch_id) |
| { |
| msr_t msr1; |
| msr_t msr2; |
| |
| /* |
| * If PRMRR/SGX is supported the FIT microcode load will set the msr |
| * 0x08b with the Patch revision id one less than the id in the |
| * microcode binary. The PRMRR support is indicated in the MSR |
| * MTRRCAP[12]. If SGX is not enabled, check and avoid reloading the |
| * same microcode during CPU initialization. If SGX is enabled, as |
| * part of SGX BIOS initialization steps, the same microcode needs to |
| * be reloaded after the core PRMRR MSRs are programmed. |
| */ |
| msr1 = rdmsr(MTRR_CAP_MSR); |
| msr2 = rdmsr(MSR_PRMRR_PHYS_BASE); |
| if (msr2.lo && (current_patch_id == new_patch_id - 1)) |
| return 0; |
| |
| return (msr1.lo & MTRR_CAP_PRMRR) && |
| (current_patch_id == new_patch_id - 1); |
| } |