| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| /* |
| * include this file into a mainboard's DSDT _SB device tree and it will expose the |
| * W83627HF SuperIO and its functionality. |
| * |
| * Devices are marked as nonexistent if they got 0x00000000 as I/O base address |
| * (compatibility with legacy bios, which disables logical devices that way) |
| * |
| * It allows the change of IO ports, IRQs and DMA settings on most logical |
| * devices, disabling and reenabling logical devices and controlling power |
| * saving mode on logical devices or the whole chip. |
| * |
| * Notes: |
| * - ECP mode of parallel port not implemented, DMA settings of parallel port |
| * will be reset on DSDT init |
| * - Hardware monitor is only shown as "Motherboard Resource", shows no real |
| * functionality |
| * |
| * Controllable through preprocessor macros: |
| * NO_W83627HF_FDC: don't expose the floppy disk controller |
| * NO_W83627HF_FDC_ENUM: don't try to enumerate the connected floppy drives |
| * NO_W83627HF_PPORT: don't expose the parallel port |
| * NO_W83627HF_UARTA: don't expose the first serial port |
| * NO_W83627HF_UARTB: don't expose the second serial port (already hidden |
| * if UARTB is configured as IRDA port by firmware) |
| * NO_W83627HF_IRDA: don't expose the IRDA port (already hidden if UARTB is |
| * configured as serial port by firmware) |
| * NO_W83627HF_CIR: don't expose the Consumer Infrared functionality |
| * NO_W83627HF_KBC: don't expose the keyboard controller |
| * NO_W83627HF_PS2M: don't expose the PS/2 mouse functionality of the |
| * keyboard controller |
| * NO_W83627HF_GAME: don't expose the game port |
| * NO_W83627HF_MIDI: don't expose the MIDI port |
| * NO_W83627HF_HWMON: don't expose the hardware monitor as |
| * PnP "Motherboard Resource" |
| * W83627HF_KBC_COMPAT: show the keyboard controller and the PS/2 mouse as |
| * enabled if it is disabled but an address is assigned |
| * to it. This may be necessary in some cases. |
| * |
| * Datasheet: "W83627HF/F WINBOND I/O" rev. 6.0 |
| * http://www.itox.com/pages/support/wdt/W83627HF.pdf |
| */ |
| |
| #include <superio/acpi/pnp.asl> |
| |
| Device(SIO) { |
| Name (_HID, EisaId("PNP0A05")) |
| Name (_STR, Unicode("Winbond W83627HF SuperIO")) |
| Name (_UID, "w83627hf") |
| |
| /* Mutex for accesses to the configuration ports (prolog and epilog commands are used, so synchronization is useful) */ |
| Mutex(CRMX, 1) |
| |
| /* SuperIO configuration ports */ |
| OperationRegion (CREG, SystemIO, SUPERIO_PNP_BASE, 0x02) |
| Field (CREG, ByteAcc, NoLock, Preserve) |
| { |
| PNP_ADDR_REG, 8, |
| PNP_DATA_REG, 8 |
| } |
| IndexField (PNP_ADDR_REG, PNP_DATA_REG, ByteAcc, NoLock, Preserve) |
| { |
| Offset (0x02), |
| RST, 1, /* Soft reset */ |
| , 7, |
| Offset (0x07), |
| LDN, 8, /* Logical device selector */ |
| Offset (0x20), |
| DID, 8, /* Device ID */ |
| DREV, 8, /* Device Revision */ |
| FDPW, 1, /* FDC Power Down */ |
| , 2, |
| PRPW, 1, /* PRT Power Down */ |
| UAPW, 1, /* UART A Power Down */ |
| UBPW, 1, /* UART B Power Down */ |
| HWPW, 1, /* HWM Power Down */ |
| , 1, |
| IPD, 1, /* Immediate Chip Power Down */ |
| , 7, |
| PNPS, 1, /* PnP Address Select Register Default Value Mode */ |
| , 1, |
| KBCR, 1, /* KBC enabled after system reset (read-only) */ |
| , 3, |
| CLKS, 1, /* Clock select */ |
| AQ16, 1, /* 16bit Address Qualification */ |
| FDCT, 1, /* Tristate FDC (?) */ |
| , 2, |
| PRTT, 1, /* Tristate parallel port (?) */ |
| URAT, 1, /* Tristate UART A (?) */ |
| URBT, 1, /* Tristate UART B (?) */ |
| , 2, |
| URAI, 1, /* UART A Legacy IRQ Select Disable */ |
| URBI, 1, /* UART B Legacy IRQ Select Disable */ |
| PRTI, 1, /* Parallel Port Legacy IRQ/DRQ Select Disable */ |
| FDCI, 1, /* FDC Legacy IRQ/DRQ Select Disable */ |
| , 1, |
| LCKC, 1, /* Lock Configuration Registers */ |
| Offset (0x29), |
| IO3S, 8, /* GPIO3 pin selection register */ |
| Offset (0x30), |
| ACTR, 1, /* Logical device activation */ |
| ACT1, 1, /* Logical part activation 1 (mostly unused) */ |
| ACT2, 1, /* Logical part activation 2 (mostly unused) */ |
| , 5, |
| Offset (0x60), |
| IO1H, 8, /* First I/O port base - high byte */ |
| IO1L, 8, /* First I/O port base - low byte */ |
| IO2H, 8, /* Second I/O port base - high byte */ |
| IO2L, 8, /* Second I/O port base - low byte */ |
| Offset (0x70), |
| IRQ0, 8, /* First IRQ */ |
| Offset (0x72), |
| IRQ1, 8, /* First IRQ */ |
| Offset (0x74), |
| DMA0, 8, /* DMA */ |
| Offset (0xE0), |
| /* CRE0-CRE4: function logical device dependent, seems to be reserved for ACPI settings */ |
| CRE0, 8, |
| CRE1, 8, |
| CRE2, 8, |
| CRE3, 8, |
| CRE4, 8, |
| Offset (0xF0), |
| /* OPT1-OPTA aka CRF0-CRF9: function logical device dependent */ |
| OPT1, 8, |
| OPT2, 8, |
| OPT3, 8, |
| OPT4, 8, |
| OPT5, 8, |
| OPT6, 8, |
| OPT7, 8, |
| OPT8, 8, |
| OPT9, 8, |
| OPTA, 8 |
| } |
| |
| Method (_CRS) |
| { |
| Return (ResourceTemplate () { |
| /* Announce the used I/O ports to the OS */ |
| IO (Decode16, SUPERIO_PNP_BASE, SUPERIO_PNP_BASE, 0x02, 0x01) |
| }) |
| } |
| |
| /* Enter configuration mode (and acquire mutex) |
| Method must be run before accessing the configuration region. |
| Parameter is the LDN which should be accessed. Values >= 0xFF mean |
| no LDN switch should be done. |
| */ |
| Method (ENTER_CONFIG_MODE, 1) |
| { |
| Acquire (CRMX, 0xFFFF) |
| ADDR = 0x87 |
| ADDR = 0x87 |
| If (Arg0 < 0xFF) { |
| LDN = Arg0 |
| } |
| } |
| |
| /* Exit configuration mode (and release mutex) |
| Method must be run after accessing the configuration region. |
| */ |
| Method (EXIT_CONFIG_MODE) |
| { |
| ADDR = 0xAA |
| Release (CRMX) |
| } |
| |
| /* PM: indicate IPD (Immediate Power Down) bit state as D0/D3 */ |
| Method (_PSC) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = IPD |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| |
| /* PM: Switch to D0 by setting IPD low */ |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| IPD = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| /* PM: Switch to D3 by setting IPD high */ |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| IPD = One |
| EXIT_CONFIG_MODE () |
| } |
| |
| #ifndef NO_W83627HF_FDC |
| /* =================== Floppy Disk Controller ================ */ |
| Device (FDC0) { |
| Name (_HID, EisaId ("PNP0700")) |
| Name (_STR, Unicode ("W83627HF Floppy Disk Controller")) |
| Name (_UID, "w83627hf-fdc") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (0) |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| /* Current power state (Returns 1 if LDN in power saving mode, |
| * 2 if whole chip is powered down), 0 else |
| */ |
| Method (_PSC) { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = FDPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| /* Disable power saving mode */ |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| FDPW = One |
| EXIT_CONFIG_MODE () |
| } |
| /* Enable power saving mode */ |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| FDPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (0) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x07, IO0) |
| IRQNoFlags () {6} |
| DMA (Compatibility, NotBusMaster, Transfer8) {2} |
| }) |
| |
| /* Get IO port info */ |
| ENTER_CONFIG_MODE (0) |
| Local0 = IO1L |
| Local1 = IO1H |
| EXIT_CONFIG_MODE () |
| |
| /* Calculate full IO port address */ |
| Local0 |= Local1 << 8 |
| |
| /* Modify the resource template and return it */ |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMIN = Local0 |
| IMAX = Local0 |
| Return (CRS) |
| } |
| |
| Method (_PRS) |
| { |
| Return (ResourceTemplate () |
| { |
| StartDependentFnNoPri () |
| { |
| IO (Decode16, 0x03F0, 0x03F0, 0x01, 0x07) |
| IRQNoFlags () {6} |
| DMA (Compatibility, NotBusMaster, Transfer8) {2} |
| } |
| EndDependentFn () |
| }) |
| } |
| |
| #ifndef NO_W83627HF_FDC_ENUM |
| Method (_FDE, 0) { |
| /* Try probing drives. |
| Probing is done through selecting and activating a drive |
| and reading 0x03F7 aka the "shared IDE and floppy register" |
| as any value there besides zero seems to indicate a |
| connected drive. |
| */ |
| // Create template |
| Name(FDE, Buffer(){0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00}) |
| CreateByteField (FDE, 1, FD1) |
| CreateByteField (FDE, 4, FD2) |
| CreateByteField (FDE, 8, FD3) |
| CreateByteField (FDE, 12, FD4) |
| |
| // Get resources from logical device |
| ENTER_CONFIG_MODE (0) |
| Local0 = ACTR |
| Local1 = IO1H |
| Local2 = IO1L |
| EXIT_CONFIG_MODE () |
| Local1 <<= 8 |
| Local1 |= Local2 |
| If (!Local0) { |
| Return (FDE) |
| } |
| |
| OperationRegion (FIO1, SystemIO, Local1, 0x06) |
| Field (FIO1, ByteAcc, NoLock, Preserve) |
| { |
| Offset(0x02), |
| SELE, 2, |
| RSTL, 1, |
| IDMA, 1, |
| ACT1, 1, |
| ACT2, 1, |
| ACT3, 1, |
| ACT4, 1, |
| Offset(0x04), |
| BSY1, 1, |
| BSY2, 1, |
| BSY3, 1, |
| BSY4, 1, |
| BUSY, 1, |
| NDMA, 1, |
| IODI, 1, |
| RDY, 1, |
| DATA, 8, |
| } |
| OperationRegion (FIO2, SystemIO, 0x3F7, 0x01) |
| Field (FIO2, ByteAcc, NoLock, Preserve) |
| { |
| SIFR, 8 |
| } |
| |
| ACT1 = One |
| SELE = 0 |
| Sleep(0x64) |
| If (SIFR) { FD1 = One } |
| |
| ACT1 = Zero |
| ACT2 = One |
| SELE = 1 |
| Sleep(0x64) |
| If (SIFR) { FD2 = One } |
| |
| ACT2 = Zero |
| ACT3 = One |
| SELE = 2 |
| Sleep(0x64) |
| If (SIFR) { FD3 = One } |
| |
| ACT3 = Zero |
| ACT4 = One |
| SELE = 3 |
| Sleep(0x64) |
| If (SIFR) { FD4 = One } |
| ACT4 = Zero |
| SELE = Zero |
| |
| Return (FDE) |
| } |
| #endif |
| |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 1, 7, IO0) |
| IRQNoFlags (IRQ0) {} |
| DMA (Compatibility, NotBusMaster, Transfer8, DMA0) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateByteField (Arg0, IRQ0._INT, IRQL) |
| CreateByteField (Arg0, DMA0._DMA, DMCH) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| ENTER_CONFIG_MODE (0) |
| IO1L = Local0 |
| IO1H = Local1 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_PPORT |
| /* ======================== Parallel Port ======================== */ |
| /* Currently no ECP support */ |
| Device (PAR0) { |
| Name (_HID, EisaId ("PNP0400")) |
| Name (_DDN, "LPT1") |
| Name (_UID, "w83627hf-pport") |
| |
| Method (MODE, 1) { |
| Local0 = Arg0 & 7 |
| ENTER_CONFIG_MODE (1) |
| Local1 = OPT1 & 3 |
| OPT1 = Local1 | Local0 |
| EXIT_CONFIG_MODE() |
| } |
| |
| Method (_INI) |
| { |
| /* Deactivate DMA, even if set by BIOS. We don't announce it |
| through _CRS and it's only useful in ECP mode which we |
| don't support at the moment. */ |
| ENTER_CONFIG_MODE (1) |
| DMA0 = 0x04 |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (1) |
| Local1 = OPT1 & 3 |
| If (ACTR) { |
| If (Local1 != 2) { |
| Local0 = 0x0D |
| } Else { |
| Local0 = 0x0D |
| } |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_PSC) { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = PRPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| PRPW = One |
| EXIT_CONFIG_MODE () |
| } |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| PRPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_DIS) { |
| ENTER_CONFIG_MODE (1) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () |
| { |
| IO (Decode16, 0x0000, 0x0000, 0x04, 0x08, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (CRS, IO0._MIN, IOP0) |
| CreateWordField (CRS, IO0._MAX, IOR0) |
| CreateByteField (CRS, IO0._ALN, IOAL) |
| CreateByteField (CRS, IO0._LEN, IOLE) |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| |
| /* Get device settings */ |
| ENTER_CONFIG_MODE (1) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = OPT1 |
| Local5 = IRQ0 |
| EXIT_CONFIG_MODE () |
| /* Calculate IO port and modify template */ |
| Local0 |= Local1 << 8 |
| IOP0 = Local1 |
| IOR0 = Local1 |
| |
| /* Set align and length based on active parallel port mode */ |
| Local3 = Local2 & 3 |
| Local4 = Local2 & 4 |
| If (Local4) { |
| IOAL = 0x04 |
| } |
| If (Local0 == 0xBC) |
| { |
| IOLE = 0x04 |
| } |
| Else |
| { |
| IOLE = 0x08 |
| } |
| /* Calculate IRQ bitmap */ |
| Local0 = One |
| IRQW = Local0 << Local5 |
| /* Return resource template */ |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| /* Traditional configurations (SPP mode) */ |
| StartDependentFn (0,1) |
| { |
| IO (Decode16, 0x0378, 0x0378, 0x04, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,1) |
| { |
| IO (Decode16, 0x0278, 0x0278, 0x04, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,1) |
| { |
| IO (Decode16, 0x03BC, 0x03BC, 0x04, 0x04) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| /* Traditional configurations (EPP mode) */ |
| StartDependentFn (0,0) |
| { |
| IO (Decode16, 0x0378, 0x0378, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) |
| { |
| IO (Decode16, 0x0278, 0x0278, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| /* Any configurable address (EPP mode) */ |
| StartDependentFn (2,0) |
| { |
| IO (Decode16, 0x0100, 0x0FF8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| /* Any configurable address (No EPP mode) */ |
| StartDependentFn (2,1) |
| { |
| IO (Decode16, 0x0100, 0x0FFC, 0x04, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn () |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 4, 4, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateWordField (Arg0, IO0._MIN, IOA1) |
| CreateByteField (Arg0, IO0._ALN, IOAL) |
| CreateByteField (Arg0, IO0._LEN, IOLE) |
| CreateWordField (Arg0, IRQX._INT, IRQL) |
| |
| If (IOAL == 4) { |
| Local2 = 0x0 |
| } else { |
| Local2 = 0x1 |
| } |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| ENTER_CONFIG_MODE (1) |
| /* IO port */ |
| IO1L = Local0 |
| IO1H = Local1 |
| /* Mode */ |
| Local3 = OPT1 |
| Local3 &= 0xF8 |
| OPT1 = Local2 | Local3 |
| /* DMA off */ |
| DMA0 = 0x04 |
| /* IRQ */ |
| IRQ0 = FindSetLeftBit (IRQL) - 1 |
| /* Activate */ |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_UARTA |
| /* =========================== UART A ============================ */ |
| Device (SER0) { |
| Name (_HID, EisaId ("PNP0501")) |
| Name (_UID, "w83627hf-uarta") |
| Name (_DDN, "COM1") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (2) |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_PSC) { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = UAPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UAPW = One |
| EXIT_CONFIG_MODE () |
| } |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UAPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (2) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x08, IO0) |
| IRQNoFlags (IRQX) {6} |
| }) |
| ENTER_CONFIG_MODE (2) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IRQ0 |
| EXIT_CONFIG_MODE () |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| IMIN = Local0 |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMAX = Local0 |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x03F8, 0x03F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02F8, 0x02F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x03E8, 0x03E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x02E8, 0x02E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (2,0) { |
| IO (Decode16, 0x0100, 0x0FF8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 1, 6, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateWordField (Arg0, IRQX._INT, IRQL) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| Local3 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (2) |
| IO1L = Local0 |
| IO1H = Local1 |
| IRQ0 = Local3 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_UARTB |
| /* =========================== UART B ============================ */ |
| Device (SER1) { |
| Name (_HID, EisaId ("PNP0501")) |
| Name (_UID, "w83627hf-uartb") |
| Name (_DDN, "COM2") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (3) |
| If (!(OPT2 & 0x30)) |
| { |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_PSC) { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = UBPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UBPW = One |
| EXIT_CONFIG_MODE () |
| } |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UBPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (3) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x08, IO0) |
| IRQNoFlags (IRQX) {6} |
| }) |
| ENTER_CONFIG_MODE (3) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IRQ0 |
| EXIT_CONFIG_MODE () |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| IMIN = Local0 |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMAX = Local0 |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02F8, 0x02F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x03F8, 0x03F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x03E8, 0x03E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x02E8, 0x02E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (2,0) { |
| IO (Decode16, 0x0100, 0x0FF8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 1, 8, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateByteField (Arg0, IRQX._INT, IRQL) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| Local3 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (3) |
| IO1L = Local0 |
| IO1H = Local1 |
| IRQ0 = Local3 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_IRDA |
| /* ======================== UART B (IRDA) ======================== */ |
| Device (IRDA) { |
| Name (_HID, EisaId ("PNP0510")) |
| Name (_UID, "w83627hf-irda") |
| Name (_STR, Unicode("IrDA Port")) |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (3) |
| If (OPT2 & 0x30) |
| { |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_PSC) { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = UBPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| Method (_PS0) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UBPW = One |
| EXIT_CONFIG_MODE () |
| } |
| Method (_PS3) { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| UBPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (3) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x08, IO0) |
| IRQNoFlags (IRQX) {6} |
| }) |
| ENTER_CONFIG_MODE (3) |
| Local1 = IO1H |
| Local0 = IO1L |
| Local2 = IRQ0 |
| EXIT_CONFIG_MODE () |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| IMIN = Local0 |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMAX = Local0 |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02F8, 0x02F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (1,0) { |
| IO (Decode16, 0x03F8, 0x03F8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x03E8, 0x03E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x02E8, 0x02E8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| StartDependentFn (2,0) { |
| IO (Decode16, 0x0100, 0x0FF8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 1, 8, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateByteField (Arg0, IRQX._INT, IRQL) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| Local3 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (3) |
| IO1L = Local0 |
| IO1H = Local1 |
| IRQ0 = Local3 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_CIR |
| /* ========================= Consumer IR ========================= */ |
| Device (CIR0) |
| { |
| Name (_HID, EisaId ("WEC1022")) /* Should be the correct one */ |
| Name (_UID, "w83627hf-cir") |
| Name (_STR, Unicode("Winbond Consumer Infrared Transceiver")) |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (6) |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (6) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x08, IO0) |
| IRQNoFlags (IRQX) {6} |
| }) |
| ENTER_CONFIG_MODE (6) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IRQ0 |
| EXIT_CONFIG_MODE () |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| IMIN = Local0 |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMAX = Local0 |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IO (Decode16, 0x0100, 0x0FF8, 0x08, 0x08) |
| IRQNoFlags () {3,4,5,7,9,10,11,12} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IO (Decode16, 0, 0, 1, 8, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateByteField (Arg0, IRQX._INT, IRQL) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| |
| Local3 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (6) |
| IO1L = Local0 |
| IO1H = Local1 |
| IRQ0 = Local3 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_KBC |
| /* ===================== Keyboard Controller ===================== */ |
| Device (KBD0) |
| { |
| Name (_HID, EisaId ("PNP0303")) |
| Name (_UID, "w83627hf-kbc") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (5) |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L || IO2H || IO2L) |
| { |
| #ifdef W83627HF_KBC_COMPAT |
| Local0 = 0x0F |
| #else |
| Local0 = 0x0D |
| #endif |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (5) |
| ACTR = Zero |
| EXIT_CONFIG_MODE () |
| Notify(PS2M, 1) |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IRQNoFlags (IRQX) {} |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x01, IO0) |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x01, IO1) |
| }) |
| ENTER_CONFIG_MODE (5) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IO2L |
| Local3 = IO2H |
| Local4 = IRQ0 |
| EXIT_CONFIG_MODE () |
| |
| Local0 |= Local1 << 8 |
| Local2 |= Local3 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| IMIN = Local0 |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMAX = Local0 |
| |
| CreateWordField (CRS, IO1._MIN, I1MI) |
| I1MI = Local2 |
| CreateWordField (CRS, IO1._MAX, I1MA) |
| I1MA = Local2 |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local5 = One |
| IRQW = Local5 << Local4 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IRQNoFlags () {1} |
| IO (Decode16, 0x0060, 0x0060, 0x01, 0x01) |
| IO (Decode16, 0x0064, 0x0064, 0x01, 0x01) |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IRQNoFlags (IRQX) {} |
| IO (Decode16, 0, 0, 1, 1, IO0) |
| IO (Decode16, 0, 0, 1, 1, IO1) |
| }) |
| CreateWordField (Arg0, IO0._MIN, IOA0) |
| CreateWordField (Arg0, IO1._MIN, IOA1) |
| CreateWordField (Arg0, IRQX._INT, IRQL) |
| |
| Divide(IOA0, 256, Local0, Local1) |
| Divide(IOA1, 256, Local2, Local3) |
| |
| Local4 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (5) |
| IO1L = Local0 |
| IO1H = Local1 |
| IO2L = Local2 |
| IO2H = Local3 |
| IRQ0 = Local4 |
| ACTR = One |
| EXIT_CONFIG_MODE () |
| Notify(PS2M, 1) |
| } |
| } |
| #ifndef NO_W83627HF_PS2M |
| Device (PS2M) |
| { |
| Name (_HID, EisaId ("PNP0F13")) |
| Name (_UID, "w83627hf-ps2m") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (5) |
| If (ACTR && IRQ1) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L || IO2H || IO2L) |
| { |
| #ifdef W83627HF_KBC_COMPAT |
| Local0 = 0x0F |
| #else |
| Local0 = 0x0D |
| #endif |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_DIS) |
| { |
| ENTER_CONFIG_MODE (5) |
| IRQ1 = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IRQNoFlags (IRQX) {} |
| }) |
| ENTER_CONFIG_MODE (5) |
| Local4 = IRQ1 |
| EXIT_CONFIG_MODE () |
| |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local5 = One |
| IRQW = Local5 << Local4 |
| |
| Return (CRS) |
| } |
| |
| Name (_PRS, ResourceTemplate () |
| { |
| StartDependentFn (0,0) { |
| IRQNoFlags () {12} |
| } |
| StartDependentFn (2,0) { |
| IRQNoFlags () {1,3,4,5,6,7,9,10,11} |
| } |
| EndDependentFn() |
| }) |
| |
| Method (_SRS, 1, Serialized) |
| { |
| Name (TMPL, ResourceTemplate () { |
| IRQNoFlags (IRQX) {} |
| }) |
| CreateWordField (Arg0, IRQX._INT, IRQL) |
| |
| Local0 = FindSetLeftBit (IRQL) - 1 |
| |
| ENTER_CONFIG_MODE (5) |
| IRQ1 = Local0 |
| /* Only activates if KBD is active */ |
| EXIT_CONFIG_MODE () |
| } |
| } |
| #endif |
| #endif |
| |
| #ifndef NO_W83627HF_GAME |
| /* ========================== Game Port ========================== */ |
| Device (GAME) |
| { |
| Name (_HID, EisaId ("PNPB02F")) |
| Name (_STR, Unicode ("Joystick/Game Port")) |
| Name (_UID, "w83627hf-game") |
| |
| Method (_STA) { |
| Local0 = 0 |
| ENTER_CONFIG_MODE (7) |
| If (IO1L || IO1H) { |
| If (ACTR || ACT1) { |
| Local0 = 0x0F |
| } |
| Else { |
| Local0 = 0x0D |
| } |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x01, 0x01, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| ENTER_CONFIG_MODE (7) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IRQ0 |
| EXIT_CONFIG_MODE () |
| |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMIN = Local0 |
| IMAX = Local0 |
| |
| If (Local2) { |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| } |
| |
| Return (CRS) |
| } |
| |
| } |
| #endif |
| |
| #ifndef NO_W83627HF_MIDI |
| /* ========================== MIDI Port ========================== */ |
| Device (MIDI) |
| { |
| Name (_HID, EisaId ("PNPB006")) |
| Name (_STR, Unicode ("MPU-401 Compatible MIDI Port")) |
| Name (_UID, "w83627hf-midi") |
| |
| Method (_STA) |
| { |
| Local0 = 0 |
| ENTER_CONFIG_MODE (7) |
| If (IO2L || IO2H) { |
| If (ACTR || ACT2) { |
| Local0 = 0x0F |
| } |
| Else { |
| Local0 = 0x0D |
| } |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_CRS) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x02, 0x02, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| ENTER_CONFIG_MODE (7) |
| Local0 = IO2L |
| Local1 = IO2H |
| Local2 = IRQ1 |
| EXIT_CONFIG_MODE () |
| |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMIN = Local0 |
| IMAX = Local0 |
| |
| If (Local2) { |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| } |
| |
| Return (CRS) |
| } |
| |
| } |
| #endif |
| |
| /* ==== Suspend LED control if it is connected to the SuperIO ==== */ |
| Method (SLED, 1) |
| { |
| ENTER_CONFIG_MODE (9) |
| Local0 = OPT4 |
| Local0 &= 63 |
| OPT4 = Local0 | ((Arg0 & 3) << 6) |
| EXIT_CONFIG_MODE () |
| } |
| |
| /* ===== Power LED control if it is connected to the SuperIO ===== */ |
| Method (PLED, 1) |
| { |
| ENTER_CONFIG_MODE (8) |
| Local0 = OPT4 |
| Local0 &= 63 |
| OPT4 = Local0 | ((Arg0 & 3) << 6) |
| EXIT_CONFIG_MODE () |
| } |
| |
| #ifndef NO_W83627HF_HWMON |
| /* ====================== Hardware Monitor ======================= */ |
| Device (HMON) |
| { |
| Name (_HID, EisaId ("PNP0C02")) // TODO: find better matching ID |
| Name (_STR, Unicode("W83627 Hardware Monitor")) |
| Name (_UID, "w83627hf-hwmon") |
| |
| Method (_STA) |
| { |
| Local0 = 0x00 |
| ENTER_CONFIG_MODE (11) |
| If (ACTR) { |
| Local0 = 0x0F |
| } |
| ElseIf (IO1H || IO1L) |
| { |
| Local0 = 0x0D |
| } |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| |
| Method (_PSC) |
| { |
| Local0 = ^^_PSC () |
| If (Local0) { Return (Local0) } |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| Local0 = HWPW |
| EXIT_CONFIG_MODE () |
| If (Local0) { Return (3) } |
| Else { Return (0) } |
| } |
| |
| Method (_PS0) |
| { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| HWPW = One |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_PS3) |
| { |
| ENTER_CONFIG_MODE (PNP_NO_LDN_CHANGE) |
| HWPW = Zero |
| EXIT_CONFIG_MODE () |
| } |
| |
| Method (_CRS, 0, Serialized) |
| { |
| Name (CRS, ResourceTemplate () { |
| IO (Decode16, 0x0000, 0x0000, 0x08, 0x02, IO0) |
| IRQNoFlags (IRQX) {} |
| }) |
| ENTER_CONFIG_MODE (11) |
| Local0 = IO1L |
| Local1 = IO1H |
| Local2 = IRQ1 |
| EXIT_CONFIG_MODE () |
| |
| Local0 |= Local1 << 8 |
| |
| CreateWordField (CRS, IO0._MIN, IMIN) |
| CreateWordField (CRS, IO0._MAX, IMAX) |
| IMIN = Local0 |
| IMAX = Local0 |
| |
| If (Local2) { |
| CreateWordField (CRS, IRQX._INT, IRQW) |
| Local3 = One |
| IRQW = Local3 << Local2 |
| } |
| Return (CRS) |
| } |
| } |
| #endif |
| |
| /* Returns the wake source register. |
| It is cleared after reading. |
| Bit 0: Keyboard wake-up event |
| Bit 1: Mouse wake-up event |
| Bit 2: Power button event |
| Bit 3: CIR wake-up event |
| Bit 4: Power loss event |
| Bit 5: VSB power loss status |
| */ |
| Method (WAKS) |
| { |
| ENTER_CONFIG_MODE (10) |
| Local0 = CRE3 |
| EXIT_CONFIG_MODE () |
| Return (Local0) |
| } |
| } |