| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <acpi/acpi.h> |
| #include <acpi/acpi_gnvs.h> |
| #include <acpi/acpigen.h> |
| #include <arch/ioapic.h> |
| #include <device/mmio.h> |
| #include <arch/smp/mpspec.h> |
| #include <cbmem.h> |
| #include <console/console.h> |
| #include <cpu/x86/smm.h> |
| #include <types.h> |
| #include <cpu/x86/msr.h> |
| #include <cpu/intel/turbo.h> |
| |
| #include <soc/acpi.h> |
| #include <soc/iomap.h> |
| #include <soc/irq.h> |
| #include <soc/msr.h> |
| #include <soc/nvs.h> |
| #include <soc/pattrs.h> |
| #include <soc/pm.h> |
| |
| #define MWAIT_RES(state, sub_state) \ |
| { \ |
| .addrl = (((state) << 4) | (sub_state)), \ |
| .space_id = ACPI_ADDRESS_SPACE_FIXED, \ |
| .bit_width = ACPI_FFIXEDHW_VENDOR_INTEL, \ |
| .bit_offset = ACPI_FFIXEDHW_CLASS_MWAIT, \ |
| .access_size = ACPI_FFIXEDHW_FLAG_HW_COORD, \ |
| } |
| |
| /* C-state map without S0ix */ |
| static acpi_cstate_t cstate_map[] = { |
| { |
| /* C1 */ |
| .ctype = 1, /* ACPI C1 */ |
| .latency = 1, |
| .power = 1000, |
| .resource = MWAIT_RES(0, 0), |
| }, |
| { |
| /* C6NS with no L2 shrink */ |
| /* NOTE: this substate is above CPUID limit */ |
| .ctype = 2, /* ACPI C2 */ |
| .latency = 500, |
| .power = 10, |
| .resource = MWAIT_RES(5, 1), |
| }, |
| { |
| /* C6FS with full L2 shrink */ |
| .ctype = 3, /* ACPI C3 */ |
| .latency = 1500, /* 1.5ms worst case */ |
| .power = 1, |
| .resource = MWAIT_RES(5, 2), |
| } |
| }; |
| |
| void soc_fill_gnvs(struct global_nvs *gnvs) |
| { |
| /* Set unknown wake source */ |
| gnvs->pm1i = -1; |
| } |
| |
| int acpi_sci_irq(void) |
| { |
| u32 *actl = (u32 *)(ILB_BASE_ADDRESS + ACTL); |
| int scis; |
| static int sci_irq; |
| |
| if (sci_irq) |
| return sci_irq; |
| |
| /* Determine how SCI is routed. */ |
| scis = read32(actl) & SCIS_MASK; |
| switch (scis) { |
| case SCIS_IRQ9: |
| case SCIS_IRQ10: |
| case SCIS_IRQ11: |
| sci_irq = scis - SCIS_IRQ9 + 9; |
| break; |
| case SCIS_IRQ20: |
| case SCIS_IRQ21: |
| case SCIS_IRQ22: |
| case SCIS_IRQ23: |
| sci_irq = scis - SCIS_IRQ20 + 20; |
| break; |
| default: |
| printk(BIOS_DEBUG, "Invalid SCI route! Defaulting to IRQ9.\n"); |
| sci_irq = 9; |
| break; |
| } |
| |
| printk(BIOS_DEBUG, "SCI is IRQ%d\n", sci_irq); |
| return sci_irq; |
| } |
| |
| unsigned long acpi_fill_mcfg(unsigned long current) |
| { |
| current += acpi_create_mcfg_mmconfig((acpi_mcfg_mmconfig_t *)current, |
| MCFG_BASE_ADDRESS, 0, 0, 255); |
| return current; |
| } |
| |
| unsigned long acpi_fill_madt(unsigned long current) |
| { |
| /* Local APICs */ |
| current = acpi_create_madt_lapics(current); |
| |
| /* IOAPIC */ |
| current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, |
| 2, IO_APIC_ADDR, 0); |
| |
| current = acpi_madt_irq_overrides(current); |
| |
| return current; |
| } |
| |
| static acpi_tstate_t soc_tss_table[] = { |
| { 100, 1000, 0, 0x00, 0 }, |
| { 88, 875, 0, 0x1e, 0 }, |
| { 75, 750, 0, 0x1c, 0 }, |
| { 63, 625, 0, 0x1a, 0 }, |
| { 50, 500, 0, 0x18, 0 }, |
| { 38, 375, 0, 0x16, 0 }, |
| { 25, 250, 0, 0x14, 0 }, |
| { 13, 125, 0, 0x12, 0 }, |
| }; |
| |
| static void generate_t_state_entries(int core, int cores_per_package) |
| { |
| /* Indicate SW_ALL coordination for T-states */ |
| acpigen_write_TSD_package(core, cores_per_package, SW_ALL); |
| |
| /* Indicate FFixedHW so OS will use MSR */ |
| acpigen_write_empty_PTC(); |
| |
| /* Set NVS controlled T-state limit */ |
| acpigen_write_TPC("\\TLVL"); |
| |
| /* Write TSS table for MSR access */ |
| acpigen_write_TSS_package(ARRAY_SIZE(soc_tss_table), soc_tss_table); |
| } |
| |
| static int calculate_power(int tdp, int p1_ratio, int ratio) |
| { |
| u32 m, power; |
| |
| /* |
| * M = ((1.1 - ((p1_ratio - ratio) * 0.00625)) / 1.1) ^ 2 |
| */ |
| |
| m = (110000 - ((p1_ratio - ratio) * 625)) / 11; |
| m = (m * m) / 1000; |
| |
| /* |
| * Power = (ratio / p1_ratio) * m * TDP |
| */ |
| power = ((ratio * 100000 / p1_ratio) / 100); |
| power *= (m / 100) * (tdp / 1000); |
| power /= 1000; |
| |
| return (int)power; |
| } |
| |
| static void generate_p_state_entries(int core, int cores_per_package) |
| { |
| int ratio_min, ratio_max, ratio_turbo, ratio_step, ratio_range_2; |
| int coord_type, power_max, power_unit, num_entries; |
| int ratio, power, clock, clock_max; |
| int vid, vid_turbo, vid_min, vid_max, vid_range_2; |
| u32 control_status; |
| const struct pattrs *pattrs = pattrs_get(); |
| msr_t msr; |
| |
| /* Inputs from CPU attributes */ |
| ratio_max = pattrs->iacore_ratios[IACORE_MAX]; |
| ratio_min = pattrs->iacore_ratios[IACORE_LFM]; |
| vid_max = pattrs->iacore_vids[IACORE_MAX]; |
| vid_min = pattrs->iacore_vids[IACORE_LFM]; |
| |
| /* Set P-states coordination type based on MSR disable bit */ |
| coord_type = (pattrs->num_cpus > 2) ? SW_ALL : HW_ALL; |
| |
| /* Max Non-Turbo Frequency */ |
| clock_max = (ratio_max * pattrs->bclk_khz) / 1000; |
| |
| /* Calculate CPU TDP in mW */ |
| msr = rdmsr(MSR_PKG_POWER_SKU_UNIT); |
| power_unit = 1 << (msr.lo & 0xf); |
| msr = rdmsr(MSR_PKG_POWER_LIMIT); |
| power_max = ((msr.lo & 0x7fff) / power_unit) * 1000; |
| |
| /* Write _PCT indicating use of FFixedHW */ |
| acpigen_write_empty_PCT(); |
| |
| /* Write _PPC with NVS specified limit on supported P-state */ |
| acpigen_write_PPC_NVS(); |
| |
| /* Write PSD indicating configured coordination type */ |
| acpigen_write_PSD_package(core, 1, coord_type); |
| |
| /* Add P-state entries in _PSS table */ |
| acpigen_write_name("_PSS"); |
| |
| /* Determine ratio points */ |
| ratio_step = 1; |
| num_entries = (ratio_max - ratio_min) / ratio_step; |
| while (num_entries > 15) { /* ACPI max is 15 ratios */ |
| ratio_step <<= 1; |
| num_entries >>= 1; |
| } |
| |
| /* P[T] is Turbo state if enabled */ |
| if (get_turbo_state() == TURBO_ENABLED) { |
| /* _PSS package count including Turbo */ |
| acpigen_write_package(num_entries + 2); |
| |
| ratio_turbo = pattrs->iacore_ratios[IACORE_TURBO]; |
| vid_turbo = pattrs->iacore_vids[IACORE_TURBO]; |
| control_status = (ratio_turbo << 8) | vid_turbo; |
| |
| /* Add entry for Turbo ratio */ |
| acpigen_write_PSS_package( |
| clock_max + 1, /* MHz */ |
| power_max, /* mW */ |
| 10, /* lat1 */ |
| 10, /* lat2 */ |
| control_status, /* control */ |
| control_status); /* status */ |
| } else { |
| /* _PSS package count without Turbo */ |
| acpigen_write_package(num_entries + 1); |
| ratio_turbo = ratio_max; |
| vid_turbo = vid_max; |
| } |
| |
| /* First regular entry is max non-turbo ratio */ |
| control_status = (ratio_max << 8) | vid_max; |
| acpigen_write_PSS_package( |
| clock_max, /* MHz */ |
| power_max, /* mW */ |
| 10, /* lat1 */ |
| 10, /* lat2 */ |
| control_status, /* control */ |
| control_status); /* status */ |
| |
| /* Set up ratio and vid ranges for VID calculation */ |
| ratio_range_2 = (ratio_turbo - ratio_min) * 2; |
| vid_range_2 = (vid_turbo - vid_min) * 2; |
| |
| /* Generate the remaining entries */ |
| for (ratio = ratio_min + ((num_entries - 1) * ratio_step); |
| ratio >= ratio_min; ratio -= ratio_step) { |
| |
| /* Calculate VID for this ratio */ |
| vid = ((ratio - ratio_min) * vid_range_2) / ratio_range_2 + vid_min; |
| |
| /* Round up if remainder */ |
| if (((ratio - ratio_min) * vid_range_2) % ratio_range_2) |
| vid++; |
| |
| /* Calculate power at this ratio */ |
| power = calculate_power(power_max, ratio_max, ratio); |
| clock = (ratio * pattrs->bclk_khz) / 1000; |
| control_status = (ratio << 8) | (vid & 0xff); |
| |
| acpigen_write_PSS_package( |
| clock, /* MHz */ |
| power, /* mW */ |
| 10, /* lat1 */ |
| 10, /* lat2 */ |
| control_status, /* control */ |
| control_status); /* status */ |
| } |
| |
| /* Fix package length */ |
| acpigen_pop_len(); |
| } |
| |
| void generate_cpu_entries(const struct device *device) |
| { |
| int core; |
| int pcontrol_blk = get_pmbase(), plen = 6; |
| const struct pattrs *pattrs = pattrs_get(); |
| |
| for (core = 0; core < pattrs->num_cpus; core++) { |
| if (core > 0) { |
| pcontrol_blk = 0; |
| plen = 0; |
| } |
| |
| /* Generate processor \_SB.CPUx */ |
| acpigen_write_processor(core, pcontrol_blk, plen); |
| |
| /* Generate P-state tables */ |
| generate_p_state_entries(core, pattrs->num_cpus); |
| |
| /* Generate C-state tables */ |
| acpigen_write_CST_package(cstate_map, ARRAY_SIZE(cstate_map)); |
| |
| /* Generate T-state tables */ |
| generate_t_state_entries(core, pattrs->num_cpus); |
| |
| acpigen_pop_len(); |
| } |
| |
| /* PPKG is usually used for thermal management |
| of the first and only package. */ |
| acpigen_write_processor_package("PPKG", 0, pattrs->num_cpus); |
| |
| /* Add a method to notify processor nodes */ |
| acpigen_write_processor_cnot(pattrs->num_cpus); |
| } |
| |
| unsigned long acpi_madt_irq_overrides(unsigned long current) |
| { |
| int sci_irq = acpi_sci_irq(); |
| acpi_madt_irqoverride_t *irqovr; |
| uint16_t sci_flags = MP_IRQ_TRIGGER_LEVEL; |
| |
| /* INT_SRC_OVR */ |
| irqovr = (void *)current; |
| current += acpi_create_madt_irqoverride(irqovr, 0, 0, 2, 0); |
| |
| if (sci_irq >= 20) |
| sci_flags |= MP_IRQ_POLARITY_LOW; |
| else |
| sci_flags |= MP_IRQ_POLARITY_HIGH; |
| |
| irqovr = (void *)current; |
| current += acpi_create_madt_irqoverride(irqovr, 0, sci_irq, sci_irq, sci_flags); |
| |
| return current; |
| } |