| # SPDX-License-Identifier: GPL-2.0-or-later |
| chip soc/amd/cezanne |
| |
| register "common_config.acp_config" = "{ |
| .acp_pin_cfg = I2S_PINS_I2S_TDM, |
| .acp_i2s_wake_enable = 0, |
| .acp_pme_enable = 0, |
| }" |
| |
| # eSPI Configuration |
| register "common_config.espi_config" = "{ |
| .std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN, |
| .generic_io_range[0] = { |
| .base = 0x62, |
| /* |
| * Only 0x62 and 0x66 are required. But, this is not supported by |
| * standard IO decodes and there are only 4 generic I/O windows |
| * available. Hence, open a window from 0x62-0x67. |
| */ |
| .size = 5, |
| }, |
| .generic_io_range[1] = { |
| .base = 0x800, /* EC_HOST_CMD_REGION0 */ |
| .size = 256, /* EC_HOST_CMD_REGION_SIZE * 2 */ |
| }, |
| .generic_io_range[2] = { |
| .base = 0x900, /* EC_LPC_ADDR_MEMMAP */ |
| .size = 255, /* EC_MEMMAP_SIZE */ |
| }, |
| .generic_io_range[3] = { |
| .base = 0x200, /* EC_LPC_ADDR_HOST_DATA */ |
| .size = 8, /* 0x200 - 0x207 */ |
| }, |
| |
| .io_mode = ESPI_IO_MODE_QUAD, |
| .op_freq_mhz = ESPI_OP_FREQ_33_MHZ, |
| .crc_check_enable = 1, |
| .alert_pin = ESPI_ALERT_PIN_IN_BAND, |
| .periph_ch_en = 1, |
| .vw_ch_en = 1, |
| .oob_ch_en = 0, |
| .flash_ch_en = 0, |
| |
| .vw_irq_polarity = ESPI_VW_IRQ_LEVEL_HIGH(1), |
| }" |
| |
| # Enable S0i3 support |
| register "s0ix_enable" = "1" |
| |
| register "system_configuration" = "2" |
| |
| register "i2c_scl_reset" = "GPIO_I2C0_SCL | GPIO_I2C1_SCL | |
| GPIO_I2C2_SCL | GPIO_I2C3_SCL" |
| |
| register "usb_phy_custom" = "1" |
| register "usb_phy" = "{ |
| .Usb2PhyPort[0] = { |
| .compdstune = 3, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 1, |
| .txpreemppulsetune = 0, |
| .txrisetune = 1, |
| .txvreftune = 6, |
| .txhsxvtune = 3, |
| .txrestune = 1, |
| }, |
| .Usb2PhyPort[1] = { |
| .compdstune = 3, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 1, |
| .txpreemppulsetune = 0, |
| .txrisetune = 1, |
| .txvreftune = 6, |
| .txhsxvtune = 3, |
| .txrestune = 1, |
| }, |
| .Usb2PhyPort[2] = { |
| .compdstune = 1, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 2, |
| .txpreemppulsetune = 0, |
| .txrisetune = 2, |
| .txvreftune = 3, |
| .txhsxvtune = 3, |
| .txrestune = 2, |
| }, |
| .Usb2PhyPort[3] = { |
| .compdstune = 1, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 2, |
| .txpreemppulsetune = 0, |
| .txrisetune = 2, |
| .txvreftune = 3, |
| .txhsxvtune = 3, |
| .txrestune = 2, |
| }, |
| .Usb2PhyPort[4] = { |
| .compdstune = 3, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 1, |
| .txpreemppulsetune = 0, |
| .txrisetune = 1, |
| .txvreftune = 6, |
| .txhsxvtune = 3, |
| .txrestune = 1, |
| }, |
| .Usb2PhyPort[5] = { |
| .compdstune = 3, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 1, |
| .txpreemppulsetune = 0, |
| .txrisetune = 1, |
| .txvreftune = 6, |
| .txhsxvtune = 3, |
| .txrestune = 1, |
| }, |
| .Usb2PhyPort[6] = { |
| .compdstune = 1, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 2, |
| .txpreemppulsetune = 0, |
| .txrisetune = 2, |
| .txvreftune = 3, |
| .txhsxvtune = 3, |
| .txrestune = 2, |
| }, |
| .Usb2PhyPort[7] = { |
| .compdstune = 1, |
| .sqrxtune = 3, |
| .txfslstune = 3, |
| .txpreempamptune = 2, |
| .txpreemppulsetune = 0, |
| .txrisetune = 2, |
| .txvreftune = 3, |
| .txhsxvtune = 3, |
| .txrestune = 2, |
| }, |
| |
| .Usb3PhyPort[0] = { |
| .tx_term_ctrl=2, |
| .rx_term_ctrl=2, |
| .tx_vboost_lvl_en=1, |
| .tx_vboost_lvl=5, |
| }, |
| .Usb3PhyPort[1] = { |
| .tx_term_ctrl=2, |
| .rx_term_ctrl=2, |
| .tx_vboost_lvl_en=1, |
| .tx_vboost_lvl=5, |
| }, |
| .Usb3PhyPort[2] = { |
| .tx_term_ctrl=2, |
| .rx_term_ctrl=2, |
| .tx_vboost_lvl_en=1, |
| .tx_vboost_lvl=5, |
| }, |
| .Usb3PhyPort[3] = { |
| .tx_term_ctrl=2, |
| .rx_term_ctrl=2, |
| .tx_vboost_lvl_en=1, |
| .tx_vboost_lvl=5, |
| }, |
| |
| .ComboPhyStaticConfig[0] = 0, |
| .ComboPhyStaticConfig[1] = 0, |
| .Version_Major = 0xd, |
| .Version_Minor = 0x4, |
| .TableLength = 100, |
| .BatteryChargerEnable = 0, |
| .PhyP3CpmP4Support = 0, |
| }" |
| |
| device domain 0 on |
| device ref gpp_bridge_0 on |
| chip drivers/wifi/generic |
| register "wake" = "GEVENT_8" |
| device pci 00.0 on end |
| end |
| end # WLAN |
| device ref gpp_bridge_1 on end # SD |
| device ref gpp_bridge_2 on end # WWAN |
| device ref gpp_bridge_3 on end # NVMe |
| |
| device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A |
| device ref gfx on end # Internal GPU (GFX) |
| device ref gfx_hda on end # GFX HD Audio Controller |
| device ref xhci_0 on # USB 3.1 (USB0) |
| chip drivers/usb/acpi |
| device ref xhci_0_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb3_port0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""User-Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""World-Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci_1 on # USB 3.1 (USB1) |
| chip drivers/usb/acpi |
| device ref xhci_1_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref usb3_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb3_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_132)" |
| device ref usb2_port6 on end |
| end |
| end |
| end |
| end |
| device ref acp on |
| chip drivers/amd/i2s_machine_dev |
| register "hid" = ""AMDI5682"" |
| device generic 0.0 on end |
| end |
| end # Audio |
| end |
| |
| device ref lpc_bridge on |
| chip ec/google/chromeec |
| device pnp 0c09.0 alias chrome_ec on end |
| end |
| end |
| end # domain |
| |
| device ref i2c_3 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "desc" = ""Cr50 TPM"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_3)" |
| device i2c 50 on end |
| end |
| end |
| |
| device ref uart_0 on end # UART0 |
| |
| # See https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/ec/baseboard/guybrush/baseboard.c;l=221 |
| # for the EC configuration. |
| # |
| # EC is configured to power off the system at 105C, so add a two degree |
| # buffer so the OS can gracefully shutdown. |
| # |
| # EC is configured to assert PROCHOT at 100C. That drastically lowers |
| # performance. Instead we will tell the OS to start throttling the CPUs |
| # at 95C in hopes that we don't hit the PROCHOT limit. |
| # |
| # We set use_acpi1_thermal_zone_scope because the Chrome ec.asl |
| # performs a `Notify` to the `_\TZ` scope. |
| chip drivers/acpi/thermal_zone |
| register "description" = ""SOC"" |
| use chrome_ec as temperature_controller |
| register "sensor_id" = "0" |
| register "polling_period" = "10" |
| register "critical_temperature" = "103" |
| register "passive_config.temperature" = "95" |
| register "use_acpi1_thermal_zone_scope" = "true" |
| |
| device generic 0 on end |
| end |
| chip drivers/acpi/thermal_zone |
| register "description" = ""Charger"" |
| use chrome_ec as temperature_controller |
| register "sensor_id" = "1" |
| register "polling_period" = "10" |
| register "critical_temperature" = "103" |
| register "passive_config.temperature" = "95" |
| register "use_acpi1_thermal_zone_scope" = "true" |
| |
| device generic 1 on end |
| end |
| chip drivers/acpi/thermal_zone |
| register "description" = ""Memory"" |
| use chrome_ec as temperature_controller |
| register "sensor_id" = "2" |
| register "polling_period" = "10" |
| register "critical_temperature" = "103" |
| register "passive_config.temperature" = "95" |
| register "use_acpi1_thermal_zone_scope" = "true" |
| |
| device generic 2 on end |
| end |
| chip drivers/acpi/thermal_zone |
| register "description" = ""CPU"" |
| use chrome_ec as temperature_controller |
| register "sensor_id" = "3" |
| register "polling_period" = "10" |
| register "critical_temperature" = "103" |
| register "passive_config.temperature" = "95" |
| register "use_acpi1_thermal_zone_scope" = "true" |
| |
| device generic 3 on end |
| end |
| end # chip soc/amd/cezanne |