| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <stdint.h> |
| #include <arch/io.h> |
| #include <console/console.h> |
| #include <northbridge/intel/sandybridge/sandybridge.h> |
| #include <northbridge/intel/sandybridge/raminit_native.h> |
| #include <southbridge/intel/common/rcba.h> |
| #include <southbridge/intel/bd82x6x/pch.h> |
| #include <superio/smsc/sch5545/sch5545.h> |
| #include <superio/smsc/sch5545/sch5545_emi.h> |
| |
| #include <baseboard/sch5545_ec.h> |
| |
| void mainboard_late_rcba_config(void) |
| { |
| DIR_ROUTE(D31IR, PIRQA, PIRQD, PIRQC, PIRQA); |
| DIR_ROUTE(D29IR, PIRQH, PIRQD, PIRQA, PIRQC); |
| DIR_ROUTE(D28IR, PIRQA, PIRQB, PIRQC, PIRQD); |
| DIR_ROUTE(D27IR, PIRQG, PIRQB, PIRQC, PIRQD); |
| DIR_ROUTE(D26IR, PIRQA, PIRQF, PIRQC, PIRQD); |
| DIR_ROUTE(D25IR, PIRQE, PIRQF, PIRQG, PIRQH); |
| DIR_ROUTE(D22IR, PIRQA, PIRQD, PIRQC, PIRQB); |
| DIR_ROUTE(D20IR, PIRQA, PIRQB, PIRQC, PIRQD); |
| } |
| |
| void mainboard_early_init(int s3resume) |
| { |
| uint16_t ec_fw_version; |
| |
| /* |
| * We do EC initialization in romstage, because it makes no sense to |
| * bloat the bootblock any more. Secondly, the EC expects to receive |
| * correct initialization sequence from the host in the time window of |
| * about 3-5 seconds since system reset. If it doesn't receive the |
| * initialization sequence, it enters an error path which results in |
| * fans spinned up to high speed. In this state EC doesn't respond to |
| * further messages sent over EMI. The issue appears after power |
| * failure, where EC loses its configuration. For this particular |
| * reasons we do the initialization in romstage instead of ramstage. |
| */ |
| sch5545_emi_init(0x2e); |
| if (sch5545_emi_get_int_mask_high()) |
| printk(BIOS_SPEW, "EC interrupt mask MSB is not 0\n"); |
| |
| sch5545_ec_hwm_early_init(); |
| |
| if (!s3resume) { |
| ec_fw_version = sch5545_get_ec_fw_version(); |
| printk(BIOS_DEBUG, "SCH5545 EC firmware version %04x\n", ec_fw_version); |
| sch5545_update_ec_firmware(ec_fw_version); |
| } |
| printk(BIOS_DEBUG, "EC early init complete.\n"); |
| |
| /* Disable SMIs and clear SMI status */ |
| outb(0, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_SMI_EN); |
| outb(SCH5545_SMI_GLOBAL_STS, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_SMI_STS); |
| } |
| |
| void mainboard_get_spd(spd_raw_data *spd, bool id_only) |
| { |
| read_spd(&spd[0], 0x50, id_only); |
| read_spd(&spd[1], 0x51, id_only); |
| read_spd(&spd[2], 0x52, id_only); |
| read_spd(&spd[3], 0x53, id_only); |
| } |