| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2009 coresystems GmbH |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <bootblock_common.h> |
| #include <stdint.h> |
| #include <arch/io.h> |
| #include <cf9_reset.h> |
| #include <device/pnp_ops.h> |
| #include <device/pci_ops.h> |
| #include <device/pci_def.h> |
| #include <option.h> |
| #include <northbridge/intel/i945/i945.h> |
| #include <southbridge/intel/i82801gx/i82801gx.h> |
| #include <superio/smsc/lpc47n227/lpc47n227.h> |
| |
| /* Override the default lpc decode ranges */ |
| void mainboard_lpc_decode(void) |
| { |
| int lpt_en = 0; |
| u8 val; |
| |
| if (get_option(&val, "lpt") == CB_SUCCESS && val) |
| lpt_en = LPT_LPC_EN; /* enable LPT */ |
| |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), LPC_IO_DEC, 0x0007); |
| |
| pci_update_config16(PCI_DEV(0, 0x1f, 0), LPC_EN, ~LPT_LPC_EN, lpt_en); |
| } |
| |
| /* This box has two superios, so enabling serial becomes slightly excessive. |
| * We disable a lot of stuff to make sure that there are no conflicts between |
| * the two. Also set up the GPIOs from the beginning. This is the "no schematic |
| * but safe anyways" method. |
| */ |
| |
| void bootblock_mainboard_early_init(void) |
| { |
| pnp_devfn_t dev; |
| |
| dev = PNP_DEV(0x2e, 0x00); |
| |
| pnp_enter_conf_state(dev); |
| pnp_write_config(dev, 0x01, 0x94); /* Extended Parport modes */ |
| pnp_write_config(dev, 0x02, 0x88); /* UART power on */ |
| pnp_write_config(dev, 0x03, 0x72); /* Floppy */ |
| pnp_write_config(dev, 0x04, 0x01); /* EPP + SPP */ |
| pnp_write_config(dev, 0x14, 0x03); /* Floppy */ |
| pnp_write_config(dev, 0x20, (0x3f0 >> 2)); /* Floppy */ |
| pnp_write_config(dev, 0x23, (0x378 >> 2)); /* PP base */ |
| pnp_write_config(dev, 0x24, (0x3f8 >> 2)); /* UART1 base */ |
| pnp_write_config(dev, 0x25, (0x2f8 >> 2)); /* UART2 base */ |
| pnp_write_config(dev, 0x26, (2 << 4) | 0); /* FDC + PP DMA */ |
| pnp_write_config(dev, 0x27, (6 << 4) | 7); /* FDC + PP DMA */ |
| pnp_write_config(dev, 0x28, (4 << 4) | 3); /* UART1,2 IRQ */ |
| /* These are the SMI status registers in the SIO: */ |
| pnp_write_config(dev, 0x30, (0x600 >> 4)); /* Runtime Register Block Base */ |
| |
| pnp_write_config(dev, 0x31, 0x00); /* GPIO1 DIR */ |
| pnp_write_config(dev, 0x32, 0x00); /* GPIO1 POL */ |
| pnp_write_config(dev, 0x33, 0x40); /* GPIO2 DIR */ |
| pnp_write_config(dev, 0x34, 0x00); /* GPIO2 POL */ |
| pnp_write_config(dev, 0x35, 0xff); /* GPIO3 DIR */ |
| pnp_write_config(dev, 0x36, 0x00); /* GPIO3 POL */ |
| pnp_write_config(dev, 0x37, 0xe0); /* GPIO4 DIR */ |
| pnp_write_config(dev, 0x38, 0x00); /* GPIO4 POL */ |
| pnp_write_config(dev, 0x39, 0x80); /* GPIO4 POL */ |
| |
| pnp_exit_conf_state(dev); |
| } |
| |
| void mainboard_late_rcba_config(void) |
| { |
| /* Device 1f interrupt pin register */ |
| RCBA32(D31IP) = 0x00042220; |
| |
| /* dev irq route register */ |
| RCBA16(D31IR) = 0x0232; |
| RCBA16(D30IR) = 0x3246; |
| RCBA16(D29IR) = 0x0237; |
| RCBA16(D28IR) = 0x3201; |
| RCBA16(D27IR) = 0x3216; |
| |
| /* Disable unused devices */ |
| RCBA32(FD) |= FD_INTLAN; |
| |
| /* This should probably go into the ACPI OS Init trap */ |
| |
| /* Set up I/O Trap #0 for 0xfe00 (SMIC) */ |
| RCBA32(0x1e84) = 0x00020001; |
| RCBA32(0x1e80) = 0x0000fe01; |
| |
| /* Set up I/O Trap #3 for 0x800-0x80c (Trap) */ |
| RCBA32(0x1e9c) = 0x000200f0; |
| RCBA32(0x1e98) = 0x000c0801; |
| } |
| |
| static void init_artec_dongle(void) |
| { |
| /* Enable 4MB decoding */ |
| outb(0xf1, 0x88); |
| outb(0xf4, 0x88); |
| } |
| |
| void mainboard_pre_raminit_config(int s3_resume) |
| { |
| init_artec_dongle(); |
| } |