| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <stdint.h> |
| #include <northbridge/intel/haswell/haswell.h> |
| #include <northbridge/intel/haswell/raminit.h> |
| #include <southbridge/intel/lynxpoint/pch.h> |
| |
| void mainboard_config_rcba(void) |
| { |
| /* |
| * GFX INTA -> PIRQA (MSI) |
| * D28IP_P1IP WLAN INTA -> PIRQB |
| * D28IP_P4IP ETH0 INTB -> PIRQC |
| * D29IP_E1P EHCI1 INTA -> PIRQD |
| * D26IP_E2P EHCI2 INTA -> PIRQE |
| * D31IP_SIP SATA INTA -> PIRQF (MSI) |
| * D31IP_SMIP SMBUS INTB -> PIRQG |
| * D31IP_TTIP THRT INTC -> PIRQH |
| * D27IP_ZIP HDA INTA -> PIRQG (MSI) |
| */ |
| |
| /* Device interrupt pin register (board specific) */ |
| RCBA32(D31IP) = (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) | |
| (INTB << D31IP_SMIP) | (INTA << D31IP_SIP); |
| RCBA32(D30IP) = (NOINT << D30IP_PIP); |
| RCBA32(D29IP) = (INTA << D29IP_E1P); |
| RCBA32(D28IP) = (INTA << D28IP_P1IP) | (INTC << D28IP_P3IP) | |
| (INTB << D28IP_P4IP); |
| RCBA32(D27IP) = (INTA << D27IP_ZIP); |
| RCBA32(D26IP) = (INTA << D26IP_E2P); |
| RCBA32(D25IP) = (NOINT << D25IP_LIP); |
| RCBA32(D22IP) = (NOINT << D22IP_MEI1IP); |
| |
| /* Device interrupt route registers */ |
| RCBA16(D31IR) = DIR_ROUTE(PIRQF, PIRQG, PIRQH, PIRQA); |
| RCBA16(D29IR) = DIR_ROUTE(PIRQD, PIRQE, PIRQF, PIRQG); |
| RCBA16(D28IR) = DIR_ROUTE(PIRQB, PIRQC, PIRQD, PIRQE); |
| RCBA16(D27IR) = DIR_ROUTE(PIRQG, PIRQH, PIRQA, PIRQB); |
| RCBA16(D26IR) = DIR_ROUTE(PIRQE, PIRQF, PIRQG, PIRQH); |
| RCBA16(D25IR) = DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD); |
| RCBA16(D22IR) = DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD); |
| } |
| |
| void mb_get_spd_map(struct spd_info *spdi) |
| { |
| spdi->addresses[0] = 0x50; |
| spdi->addresses[1] = 0x51; |
| spdi->addresses[2] = 0x52; |
| spdi->addresses[3] = 0x53; |
| } |
| |
| const struct usb2_port_config mainboard_usb2_ports[MAX_USB2_PORTS] = { |
| /* Length, Enable, OCn#, Location */ |
| { 0x0040, 1, 0, /* P0: Back USB3 port (OC0) */ |
| USB_PORT_BACK_PANEL }, |
| { 0x0040, 1, 0, /* P1: Back USB3 port (OC0) */ |
| USB_PORT_BACK_PANEL }, |
| { 0x0040, 1, 1, /* P2: Flex Port on bottom (OC1) */ |
| USB_PORT_FLEX }, |
| { 0x0040, 1, USB_OC_PIN_SKIP, /* P3: Dock connector */ |
| USB_PORT_DOCK }, |
| { 0x0040, 1, USB_OC_PIN_SKIP, /* P4: Mini PCIE */ |
| USB_PORT_MINI_PCIE }, |
| { 0x0040, 1, 1, /* P5: USB eSATA header (OC1) */ |
| USB_PORT_FLEX }, |
| { 0x0040, 1, 3, /* P6: Front Header J8H2 (OC3) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 3, /* P7: Front Header J8H2 (OC3) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 4, /* P8: USB/LAN Jack (OC4) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 4, /* P9: USB/LAN Jack (OC4) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 5, /* P10: Front Header J7H3 (OC5) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 5, /* P11: Front Header J7H3 (OC5) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 6, /* P12: USB/DP Jack (OC6) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 6, /* P13: USB/DP Jack (OC6) */ |
| USB_PORT_FRONT_PANEL }, |
| }; |
| |
| const struct usb3_port_config mainboard_usb3_ports[MAX_USB3_PORTS] = { |
| /* Enable, OCn# */ |
| { 1, 0 }, /* P1; */ |
| { 1, 0 }, /* P2; */ |
| { 1, 0 }, /* P3; */ |
| { 1, 0 }, /* P4; */ |
| { 1, 0 }, /* P6; */ |
| { 1, 0 }, /* P6; */ |
| }; |