| /* |
| * PCI Bus Services, see include/linux/pci.h for further explanation. |
| * |
| * Copyright 1993 -- 1997 Drew Eckhardt, Frederic Potter, |
| * David Mosberger-Tang |
| * |
| * Copyright 1997 -- 1999 Martin Mares <mj@atrey.karlin.mff.cuni.cz> |
| * |
| * Copyright 2003 -- Eric Biederman <ebiederman@lnxi.com> |
| */ |
| |
| #include <console/console.h> |
| #include <stdlib.h> |
| #include <stdint.h> |
| #include <bitops.h> |
| #include <string.h> |
| #include <arch/io.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pci_ids.h> |
| #include <part/hard_reset.h> |
| #include <part/fallback_boot.h> |
| #include <delay.h> |
| |
| static uint8_t pci_moving_config8(struct device *dev, unsigned reg) |
| { |
| uint8_t value, ones, zeroes; |
| value = pci_read_config8(dev, reg); |
| |
| pci_write_config8(dev, reg, 0xff); |
| ones = pci_read_config8(dev, reg); |
| |
| pci_write_config8(dev, reg, 0x00); |
| zeroes = pci_read_config8(dev, reg); |
| |
| pci_write_config8(dev, reg, value); |
| |
| return ones ^ zeroes; |
| } |
| |
| static uint16_t pci_moving_config16(struct device *dev, unsigned reg) |
| { |
| uint16_t value, ones, zeroes; |
| value = pci_read_config16(dev, reg); |
| |
| pci_write_config16(dev, reg, 0xffff); |
| ones = pci_read_config16(dev, reg); |
| |
| pci_write_config16(dev, reg, 0x0000); |
| zeroes = pci_read_config16(dev, reg); |
| |
| pci_write_config16(dev, reg, value); |
| |
| return ones ^ zeroes; |
| } |
| |
| static uint32_t pci_moving_config32(struct device *dev, unsigned reg) |
| { |
| uint32_t value, ones, zeroes; |
| value = pci_read_config32(dev, reg); |
| |
| pci_write_config32(dev, reg, 0xffffffff); |
| ones = pci_read_config32(dev, reg); |
| |
| pci_write_config32(dev, reg, 0x00000000); |
| zeroes = pci_read_config32(dev, reg); |
| |
| pci_write_config32(dev, reg, value); |
| |
| return ones ^ zeroes; |
| } |
| |
| unsigned pci_find_capability(device_t dev, unsigned cap) |
| { |
| unsigned pos; |
| pos = 0; |
| switch(dev->hdr_type & 0x7f) { |
| case PCI_HEADER_TYPE_NORMAL: |
| case PCI_HEADER_TYPE_BRIDGE: |
| pos = PCI_CAPABILITY_LIST; |
| break; |
| } |
| if (pos > PCI_CAP_LIST_NEXT) { |
| pos = pci_read_config8(dev, pos); |
| } |
| while (pos != 0) { /* loop through the linked list */ |
| int this_cap; |
| this_cap = pci_read_config8(dev, pos + PCI_CAP_LIST_ID); |
| if (this_cap == cap) { |
| return pos; |
| } |
| } |
| return 0; |
| } |
| |
| /** Given a device and register, read the size of the BAR for that register. |
| * @param dev Pointer to the device structure |
| * @param resource Pointer to the resource structure |
| * @param index Address of the pci configuration register |
| */ |
| struct resource *pci_get_resource(struct device *dev, unsigned long index) |
| { |
| struct resource *resource; |
| unsigned long value, attr; |
| resource_t moving, limit; |
| |
| /* Initialize the resources to nothing */ |
| resource = new_resource(dev, index); |
| |
| /* Get the initial value */ |
| value = pci_read_config32(dev, index); |
| |
| /* See which bits move */ |
| moving = pci_moving_config32(dev, index); |
| |
| /* Initialize attr to the bits that do not move */ |
| attr = value & ~moving; |
| |
| /* If it is a 64bit resource look at the high half as well */ |
| if (((attr & PCI_BASE_ADDRESS_SPACE_IO) == 0) && |
| ((attr & PCI_BASE_ADDRESS_MEM_LIMIT_MASK) == PCI_BASE_ADDRESS_MEM_LIMIT_64)) |
| { |
| /* Find the high bits that move */ |
| moving |= ((resource_t)pci_moving_config32(dev, index + 4)) << 32; |
| } |
| /* Find the resource constraints. |
| * |
| * Start by finding the bits that move. From there: |
| * - Size is the least significant bit of the bits that move. |
| * - Limit is all of the bits that move plus all of the lower bits. |
| * See PCI Spec 6.2.5.1 ... |
| */ |
| limit = 0; |
| if (moving) { |
| resource->size = 1; |
| resource->align = resource->gran = 0; |
| while (!(moving & resource->size)) { |
| resource->size <<= 1; |
| resource->align += 1; |
| resource->gran += 1; |
| } |
| resource->limit = limit = moving | (resource->size - 1); |
| } |
| /* |
| * some broken hardware has read-only registers that do not |
| * really size correctly. |
| * Example: the acer m7229 has BARs 1-4 normally read-only. |
| * so BAR1 at offset 0x10 reads 0x1f1. If you size that register |
| * by writing 0xffffffff to it, it will read back as 0x1f1 -- a |
| * violation of the spec. |
| * We catch this case and ignore it by observing which bits move, |
| * This also catches the common case unimplemented registers |
| * that always read back as 0. |
| */ |
| if (moving == 0) { |
| if (value != 0) { |
| printk_debug("%s register %02x(%08x), read-only ignoring it\n", |
| dev_path(dev), index, value); |
| } |
| resource->flags = 0; |
| } else if (attr & PCI_BASE_ADDRESS_SPACE_IO) { |
| /* An I/O mapped base address */ |
| attr &= PCI_BASE_ADDRESS_IO_ATTR_MASK; |
| resource->flags |= IORESOURCE_IO; |
| /* I don't want to deal with 32bit I/O resources */ |
| resource->limit = 0xffff; |
| } else { |
| /* A Memory mapped base address */ |
| attr &= PCI_BASE_ADDRESS_MEM_ATTR_MASK; |
| resource->flags |= IORESOURCE_MEM; |
| if (attr & PCI_BASE_ADDRESS_MEM_PREFETCH) { |
| resource->flags |= IORESOURCE_PREFETCH; |
| } |
| attr &= PCI_BASE_ADDRESS_MEM_LIMIT_MASK; |
| if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_32) { |
| /* 32bit limit */ |
| resource->limit = 0xffffffffUL; |
| } else if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_1M) { |
| /* 1MB limit */ |
| resource->limit = 0x000fffffUL; |
| } else if (attr == PCI_BASE_ADDRESS_MEM_LIMIT_64) { |
| /* 64bit limit */ |
| resource->limit = 0xffffffffffffffffULL; |
| resource->flags |= IORESOURCE_PCI64; |
| } else { |
| /* Invalid value */ |
| resource->flags = 0; |
| } |
| } |
| /* Don't let the limit exceed which bits can move */ |
| if (resource->limit > limit) { |
| resource->limit = limit; |
| } |
| #if 0 |
| if (resource->flags) { |
| printk_debug("%s %02x ->", |
| dev_path(dev), resource->index); |
| printk_debug(" value: 0x%08Lx zeroes: 0x%08Lx ones: 0x%08Lx attr: %08lx\n", |
| value, zeroes, ones, attr); |
| printk_debug( |
| "%s %02x -> size: 0x%08Lx max: 0x%08Lx %s%s\n ", |
| dev_path(dev), |
| resource->index, |
| resource->size, resource->limit, |
| (resource->flags == 0) ? "unused": |
| (resource->flags & IORESOURCE_IO)? "io": |
| (resource->flags & IORESOURCE_PREFETCH)? "prefmem": "mem", |
| (resource->flags & IORESOURCE_PCI64)?"64":""); |
| } |
| #endif |
| |
| return resource; |
| } |
| |
| static void pci_get_rom_resource(struct device *dev, unsigned long index) |
| { |
| struct resource *resource; |
| unsigned long value; |
| resource_t moving, limit; |
| |
| /* Initialize the resources to nothing */ |
| resource = new_resource(dev, index); |
| |
| /* Get the initial value */ |
| value = pci_read_config32(dev, index); |
| |
| /* See which bits move */ |
| moving = pci_moving_config32(dev, index); |
| /* clear the Enable bit */ |
| moving = moving & ~PCI_ROM_ADDRESS_ENABLE; |
| |
| /* Find the resource constraints. |
| * |
| * Start by finding the bits that move. From there: |
| * - Size is the least significant bit of the bits that move. |
| * - Limit is all of the bits that move plus all of the lower bits. |
| * See PCI Spec 6.2.5.1 ... |
| */ |
| limit = 0; |
| |
| if (moving) { |
| resource->size = 1; |
| resource->align = resource->gran = 0; |
| while (!(moving & resource->size)) { |
| resource->size <<= 1; |
| resource->align += 1; |
| resource->gran += 1; |
| } |
| resource->limit = limit = moving | (resource->size - 1); |
| } |
| |
| if (moving == 0) { |
| if (value != 0) { |
| printk_debug("%s register %02x(%08x), read-only ignoring it\n", |
| dev_path(dev), index, value); |
| } |
| resource->flags = 0; |
| } else { |
| resource->flags |= IORESOURCE_MEM | IORESOURCE_READONLY; |
| } |
| |
| /* for on board device with embedded ROM image, the ROM image is at |
| * fixed address specified in the Config.lb, the dev->rom_address is |
| * inited by driver_pci_onboard_ops::enable_dev() */ |
| if ((dev->on_mainboard) && (dev->rom_address == 0)) { |
| resource->base = dev->rom_address; |
| resource->flags |= IORESOURCE_MEM | IORESOURCE_READONLY | |
| IORESOURCE_ASSIGNED | IORESOURCE_FIXED; |
| } |
| } |
| |
| /** Read the base address registers for a given device. |
| * @param dev Pointer to the dev structure |
| * @param howmany How many registers to read (6 for device, 2 for bridge) |
| */ |
| static void pci_read_bases(struct device *dev, unsigned int howmany, unsigned long rom) |
| { |
| unsigned long index; |
| |
| for (index = PCI_BASE_ADDRESS_0; (index < PCI_BASE_ADDRESS_0 + (howmany << 2)); ) { |
| struct resource *resource; |
| resource = pci_get_resource(dev, index); |
| index += (resource->flags & IORESOURCE_PCI64)?8:4; |
| } |
| if (rom) |
| pci_get_rom_resource(dev, rom); |
| |
| compact_resources(dev); |
| } |
| |
| static void pci_set_resource(struct device *dev, struct resource *resource); |
| |
| static void pci_record_bridge_resource( struct device *dev, resource_t moving, |
| unsigned index, unsigned long mask, |
| unsigned long type) |
| { |
| /* Initiliaze the constraints on the current bus */ |
| struct resource *resource; |
| resource = 0; |
| if (moving) { |
| unsigned long gran; |
| resource_t step; |
| resource = new_resource(dev, index); |
| resource->size = 0; |
| gran = 0; |
| step = 1; |
| while((moving & step) == 0) { |
| gran += 1; |
| step <<= 1; |
| } |
| resource->gran = gran; |
| resource->align = gran; |
| resource->limit = moving | (step - 1); |
| resource->flags = type | IORESOURCE_PCI_BRIDGE; |
| compute_allocate_resource(&dev->link[0], resource, mask, type); |
| /* If there is nothing behind the resource, |
| * clear it and forget it. |
| */ |
| if (resource->size == 0) { |
| resource->base = moving; |
| resource->flags |= IORESOURCE_ASSIGNED; |
| resource->flags &= ~IORESOURCE_STORED; |
| pci_set_resource(dev, resource); |
| resource->flags = 0; |
| } |
| } |
| return; |
| } |
| |
| static void pci_bridge_read_bases(struct device *dev) |
| { |
| resource_t moving_base, moving_limit, moving; |
| |
| /* See if the bridge I/O resources are implemented */ |
| moving_base = ((uint32_t)pci_moving_config8(dev, PCI_IO_BASE)) << 8; |
| moving_base |= ((uint32_t)pci_moving_config16(dev, PCI_IO_BASE_UPPER16)) << 16; |
| |
| moving_limit = ((uint32_t)pci_moving_config8(dev, PCI_IO_LIMIT)) << 8; |
| moving_limit |= ((uint32_t)pci_moving_config16(dev, PCI_IO_LIMIT_UPPER16)) << 16; |
| |
| moving = moving_base & moving_limit; |
| |
| /* Initialize the io space constraints on the current bus */ |
| pci_record_bridge_resource(dev, moving, PCI_IO_BASE, |
| IORESOURCE_IO, IORESOURCE_IO); |
| |
| /* See if the bridge prefmem resources are implemented */ |
| moving_base = ((resource_t)pci_moving_config16(dev, PCI_PREF_MEMORY_BASE)) << 16; |
| moving_base |= ((resource_t)pci_moving_config32(dev, PCI_PREF_BASE_UPPER32)) << 32; |
| |
| moving_limit = ((resource_t)pci_moving_config16(dev, PCI_PREF_MEMORY_LIMIT)) << 16; |
| moving_limit |= ((resource_t)pci_moving_config32(dev, PCI_PREF_LIMIT_UPPER32)) << 32; |
| |
| moving = moving_base & moving_limit; |
| /* Initiliaze the prefetchable memory constraints on the current bus */ |
| pci_record_bridge_resource(dev, moving, PCI_PREF_MEMORY_BASE, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH); |
| |
| /* See if the bridge mem resources are implemented */ |
| moving_base = ((uint32_t)pci_moving_config16(dev, PCI_MEMORY_BASE)) << 16; |
| moving_limit = ((uint32_t)pci_moving_config16(dev, PCI_MEMORY_LIMIT)) << 16; |
| |
| moving = moving_base & moving_limit; |
| |
| /* Initialize the memory resources on the current bus */ |
| pci_record_bridge_resource(dev, moving, PCI_MEMORY_BASE, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH, |
| IORESOURCE_MEM); |
| |
| compact_resources(dev); |
| } |
| |
| void pci_dev_read_resources(struct device *dev) |
| { |
| uint32_t addr; |
| |
| pci_read_bases(dev, 6, PCI_ROM_ADDRESS); |
| } |
| |
| void pci_bus_read_resources(struct device *dev) |
| { |
| uint32_t addr; |
| |
| pci_bridge_read_bases(dev); |
| pci_read_bases(dev, 2, PCI_ROM_ADDRESS1); |
| } |
| |
| static void pci_set_resource(struct device *dev, struct resource *resource) |
| { |
| resource_t base, end; |
| |
| /* Make certain the resource has actually been set */ |
| if (!(resource->flags & IORESOURCE_ASSIGNED)) { |
| printk_err("ERROR: %s %02x not allocated\n", |
| dev_path(dev), resource->index); |
| return; |
| } |
| |
| /* If I have already stored this resource don't worry about it */ |
| if (resource->flags & IORESOURCE_STORED) { |
| return; |
| } |
| |
| /* If the resources is substractive don't worry about it */ |
| if (resource->flags & IORESOURCE_SUBTRACTIVE) { |
| return; |
| } |
| |
| /* Only handle PCI memory and IO resources for now */ |
| if (!(resource->flags & (IORESOURCE_MEM |IORESOURCE_IO))) |
| return; |
| |
| /* Enable the resources in the command register */ |
| if (resource->size) { |
| if (resource->flags & IORESOURCE_MEM) { |
| dev->command |= PCI_COMMAND_MEMORY; |
| } |
| if (resource->flags & IORESOURCE_IO) { |
| dev->command |= PCI_COMMAND_IO; |
| } |
| if (resource->flags & IORESOURCE_PCI_BRIDGE) { |
| dev->command |= PCI_COMMAND_MASTER; |
| } |
| } |
| /* Get the base address */ |
| base = resource->base; |
| |
| /* Get the end */ |
| end = resource_end(resource); |
| |
| /* Now store the resource */ |
| resource->flags |= IORESOURCE_STORED; |
| if (!(resource->flags & IORESOURCE_PCI_BRIDGE)) { |
| unsigned long base_lo, base_hi; |
| /* |
| * some chipsets allow us to set/clear the IO bit. |
| * (e.g. VIA 82c686a.) So set it to be safe) |
| */ |
| base_lo = base & 0xffffffff; |
| base_hi = (base >> 32) & 0xffffffff; |
| if (resource->flags & IORESOURCE_IO) { |
| base_lo |= PCI_BASE_ADDRESS_SPACE_IO; |
| } |
| pci_write_config32(dev, resource->index, base_lo); |
| if (resource->flags & IORESOURCE_PCI64) { |
| pci_write_config32(dev, resource->index + 4, base_hi); |
| } |
| } |
| else if (resource->index == PCI_IO_BASE) { |
| /* set the IO ranges */ |
| compute_allocate_resource(&dev->link[0], resource, |
| IORESOURCE_IO, IORESOURCE_IO); |
| pci_write_config8(dev, PCI_IO_BASE, base >> 8); |
| pci_write_config16(dev, PCI_IO_BASE_UPPER16, base >> 16); |
| pci_write_config8(dev, PCI_IO_LIMIT, end >> 8); |
| pci_write_config16(dev, PCI_IO_LIMIT_UPPER16, end >> 16); |
| } |
| else if (resource->index == PCI_MEMORY_BASE) { |
| /* set the memory range */ |
| compute_allocate_resource(&dev->link[0], resource, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH, |
| IORESOURCE_MEM); |
| pci_write_config16(dev, PCI_MEMORY_BASE, base >> 16); |
| pci_write_config16(dev, PCI_MEMORY_LIMIT, end >> 16); |
| } |
| else if (resource->index == PCI_PREF_MEMORY_BASE) { |
| /* set the prefetchable memory range */ |
| compute_allocate_resource(&dev->link[0], resource, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH, |
| IORESOURCE_MEM | IORESOURCE_PREFETCH); |
| pci_write_config16(dev, PCI_PREF_MEMORY_BASE, base >> 16); |
| pci_write_config32(dev, PCI_PREF_BASE_UPPER32, base >> 32); |
| pci_write_config16(dev, PCI_PREF_MEMORY_LIMIT, end >> 16); |
| pci_write_config32(dev, PCI_PREF_LIMIT_UPPER32, end >> 32); |
| } |
| else { |
| /* Don't let me think I stored the resource */ |
| resource->flags &= ~IORESOURCE_STORED; |
| printk_err("ERROR: invalid resource->index %x\n", |
| resource->index); |
| } |
| report_resource_stored(dev, resource, ""); |
| return; |
| } |
| |
| void pci_dev_set_resources(struct device *dev) |
| { |
| struct resource *resource, *last; |
| unsigned link; |
| uint8_t line; |
| |
| last = &dev->resource[dev->resources]; |
| |
| for (resource = &dev->resource[0]; resource < last; resource++) { |
| pci_set_resource(dev, resource); |
| } |
| for (link = 0; link < dev->links; link++) { |
| struct bus *bus; |
| bus = &dev->link[link]; |
| if (bus->children) { |
| assign_resources(bus); |
| } |
| } |
| |
| /* set a default latency timer */ |
| pci_write_config8(dev, PCI_LATENCY_TIMER, 0x40); |
| |
| /* set a default secondary latency timer */ |
| if ((dev->hdr_type & 0x7f) == PCI_HEADER_TYPE_BRIDGE) { |
| pci_write_config8(dev, PCI_SEC_LATENCY_TIMER, 0x40); |
| } |
| |
| /* zero the irq settings */ |
| line = pci_read_config8(dev, PCI_INTERRUPT_PIN); |
| if (line) { |
| pci_write_config8(dev, PCI_INTERRUPT_LINE, 0); |
| } |
| /* set the cache line size, so far 64 bytes is good for everyone */ |
| pci_write_config8(dev, PCI_CACHE_LINE_SIZE, 64 >> 2); |
| } |
| |
| void pci_dev_enable_resources(struct device *dev) |
| { |
| const struct pci_operations *ops; |
| uint16_t command; |
| |
| /* Set the subsystem vendor and device id for mainboard devices */ |
| ops = ops_pci(dev); |
| if (dev->on_mainboard && ops && ops->set_subsystem) { |
| printk_debug("%s subsystem <- %02x/%02x\n", |
| dev_path(dev), |
| MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID, |
| MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID); |
| ops->set_subsystem(dev, |
| MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID, |
| MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID); |
| } |
| command = pci_read_config16(dev, PCI_COMMAND); |
| command |= dev->command; |
| command |= (PCI_COMMAND_PARITY + PCI_COMMAND_SERR); /* error check */ |
| printk_debug("%s cmd <- %02x\n", dev_path(dev), command); |
| pci_write_config16(dev, PCI_COMMAND, command); |
| } |
| |
| void pci_bus_enable_resources(struct device *dev) |
| { |
| uint16_t ctrl; |
| |
| /* enable IO in command register if there is VGA card |
| * connected with (even it does not claim IO resource) */ |
| if (dev->link[0].bridge_ctrl & PCI_BRIDGE_CTL_VGA) |
| dev->command |= PCI_COMMAND_IO; |
| |
| ctrl = pci_read_config16(dev, PCI_BRIDGE_CONTROL); |
| ctrl |= dev->link[0].bridge_ctrl; |
| ctrl |= (PCI_BRIDGE_CTL_PARITY + PCI_BRIDGE_CTL_SERR); /* error check */ |
| printk_debug("%s bridge ctrl <- %04x\n", dev_path(dev), ctrl); |
| pci_write_config16(dev, PCI_BRIDGE_CONTROL, ctrl); |
| |
| pci_dev_enable_resources(dev); |
| |
| enable_childrens_resources(dev); |
| } |
| |
| void pci_dev_set_subsystem(device_t dev, unsigned vendor, unsigned device) |
| { |
| pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID, |
| ((device & 0xffff) << 16) | (vendor & 0xffff)); |
| } |
| |
| void pci_dev_init(struct device *dev) |
| { |
| struct rom_header *rom, *ram; |
| |
| rom = pci_rom_probe(dev); |
| if (rom == NULL) |
| return; |
| ram = pci_rom_load(dev, rom); |
| |
| run_bios(dev, ram); |
| } |
| |
| /** Default device operation for PCI devices */ |
| static struct pci_operations pci_dev_ops_pci = { |
| .set_subsystem = pci_dev_set_subsystem, |
| }; |
| |
| struct device_operations default_pci_ops_dev = { |
| .read_resources = pci_dev_read_resources, |
| .set_resources = pci_dev_set_resources, |
| .enable_resources = pci_dev_enable_resources, |
| .init = pci_dev_init, |
| .scan_bus = 0, |
| .enable = 0, |
| .ops_pci = &pci_dev_ops_pci, |
| }; |
| |
| /** Default device operations for PCI bridges */ |
| static struct pci_operations pci_bus_ops_pci = { |
| .set_subsystem = 0, |
| }; |
| |
| struct device_operations default_pci_ops_bus = { |
| .read_resources = pci_bus_read_resources, |
| .set_resources = pci_dev_set_resources, |
| .enable_resources = pci_bus_enable_resources, |
| .init = 0, |
| .scan_bus = pci_scan_bridge, |
| .enable = 0, |
| .ops_pci = &pci_bus_ops_pci, |
| }; |
| |
| /** |
| * @brief Set up PCI device operation |
| * |
| * |
| * @param dev |
| * |
| * @see pci_drivers |
| */ |
| static void set_pci_ops(struct device *dev) |
| { |
| struct pci_driver *driver; |
| if (dev->ops) { |
| return; |
| } |
| |
| /* Look through the list of setup drivers and find one for |
| * this pci device |
| */ |
| for (driver = &pci_drivers[0]; driver != &epci_drivers[0]; driver++) { |
| if ((driver->vendor == dev->vendor) && |
| (driver->device == dev->device)) |
| { |
| dev->ops = driver->ops; |
| printk_debug("%s [%04x/%04x] %sops\n", |
| dev_path(dev), |
| driver->vendor, driver->device, |
| (driver->ops->scan_bus?"bus ":"")); |
| return; |
| } |
| } |
| |
| /* If I don't have a specific driver use the default operations */ |
| switch(dev->hdr_type & 0x7f) { /* header type */ |
| case PCI_HEADER_TYPE_NORMAL: /* standard header */ |
| if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) |
| goto bad; |
| dev->ops = &default_pci_ops_dev; |
| break; |
| case PCI_HEADER_TYPE_BRIDGE: |
| if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI) |
| goto bad; |
| dev->ops = &default_pci_ops_bus; |
| break; |
| default: |
| bad: |
| if (dev->enabled) { |
| printk_err("%s [%04x/%04x/%06x] has unknown header " |
| "type %02x, ignoring.\n", |
| dev_path(dev), |
| dev->vendor, dev->device, |
| dev->class >> 8, dev->hdr_type); |
| } |
| } |
| return; |
| } |
| |
| /** |
| * @brief See if we have already allocated a device structure for a given devfn. |
| * |
| * Given a linked list of PCI device structures and a devfn number, find the |
| * device structure correspond to the devfn, if present. This function also |
| * removes the device structure from the linked list. |
| * |
| * @param list the device structure list |
| * @param devfn a device/function number |
| * |
| * @return pointer to the device structure found or null of we have not |
| * allocated a device for this devfn yet. |
| */ |
| static struct device *pci_scan_get_dev(struct device **list, unsigned int devfn) |
| { |
| struct device *dev; |
| dev = 0; |
| for(; *list; list = &(*list)->sibling) { |
| if ((*list)->path.type != DEVICE_PATH_PCI) { |
| printk_err("child %s not a pci device\n", |
| dev_path(*list)); |
| continue; |
| } |
| if ((*list)->path.u.pci.devfn == devfn) { |
| /* Unlink from the list */ |
| dev = *list; |
| *list = (*list)->sibling; |
| dev->sibling = 0; |
| break; |
| } |
| } |
| /* Just like alloc_dev add the device to the list of device on the bus. |
| * When the list of devices was formed we removed all of the parents |
| * children, and now we are interleaving static and dynamic devices in |
| * order on the bus. |
| */ |
| if (dev) { |
| device_t child; |
| /* Find the last child of our parent */ |
| for (child = dev->bus->children; child && child->sibling; ) { |
| child = child->sibling; |
| } |
| /* Place the device on the list of children of it's parent. */ |
| if (child) { |
| child->sibling = dev; |
| } else { |
| dev->bus->children = dev; |
| } |
| } |
| |
| return dev; |
| } |
| |
| /** |
| * @brief Scan a PCI bus. |
| * |
| * Determine the existence of devices and bridges on a PCI bus. If there are |
| * bridges on the bus, recursively scan the buses behind the bridges. |
| * |
| * @param bus pointer to the bus structure |
| * @param min_devfn minimum devfn to look at in the scan usually 0x00 |
| * @param max_devfn maximum devfn to look at in the scan usually 0xff |
| * @param max current bus number |
| * |
| * @return The maximum bus number found, after scanning all subordinate busses |
| */ |
| unsigned int pci_scan_bus(struct bus *bus, unsigned min_devfn, unsigned max_devfn, |
| unsigned int max) |
| { |
| unsigned int devfn; |
| device_t dev; |
| device_t old_devices; |
| device_t child; |
| |
| printk_debug("PCI: pci_scan_bus for bus %d\n", bus->secondary); |
| |
| old_devices = bus->children; |
| bus->children = 0; |
| |
| post_code(0x24); |
| |
| /* probe all devices/functions on this bus with some optimization for |
| * non-existence and single funcion devices |
| */ |
| for (devfn = min_devfn; devfn <= max_devfn; devfn++) { |
| uint32_t id, class; |
| uint8_t hdr_type; |
| |
| /* First thing setup the device structure */ |
| dev = pci_scan_get_dev(&old_devices, devfn); |
| |
| /* Detect if a device is present */ |
| if (!dev) { |
| struct device dummy; |
| dummy.bus = bus; |
| dummy.path.type = DEVICE_PATH_PCI; |
| dummy.path.u.pci.devfn = devfn; |
| id = pci_read_config32(&dummy, PCI_VENDOR_ID); |
| /* some broken boards return 0 if a slot is empty: */ |
| if ((id == 0xffffffff) || (id == 0x00000000) || |
| (id == 0x0000ffff) || (id == 0xffff0000)) |
| { |
| printk_spew("PCI: devfn 0x%x, bad id 0x%x\n", devfn, id); |
| if (PCI_FUNC(devfn) == 0x00) { |
| /* if this is a function 0 device and |
| * it is not present, |
| * skip to next device |
| */ |
| devfn += 0x07; |
| } |
| /* This function in a multi function device is |
| * not present, skip to the next function. |
| */ |
| continue; |
| } |
| dev = alloc_dev(bus, &dummy.path); |
| } |
| else { |
| /* Enable/disable the device. Once we have |
| * found the device specific operations this |
| * operations we will disable the device with |
| * those as well. |
| * |
| * This is geared toward devices that have subfunctions |
| * that do not show up by default. |
| * |
| * If a device is a stuff option on the motherboard |
| * it may be absent and enable_dev must cope. |
| * |
| */ |
| if (dev->chip_ops && dev->chip_ops->enable_dev) |
| { |
| dev->chip_ops->enable_dev(dev); |
| } |
| /* Now read the vendor and device id */ |
| id = pci_read_config32(dev, PCI_VENDOR_ID); |
| |
| /* If the device does not have a pci id disable it. |
| * Possibly this is because we have already disabled |
| * the device. But this also handles optional devices |
| * that may not always show up. |
| */ |
| if (id == 0xffffffff || id == 0x00000000 || |
| id == 0x0000ffff || id == 0xffff0000) |
| { |
| if (dev->enabled) { |
| printk_info("Disabling static device: %s\n", |
| dev_path(dev)); |
| dev->enabled = 0; |
| } |
| } |
| } |
| /* Read the rest of the pci configuration information */ |
| hdr_type = pci_read_config8(dev, PCI_HEADER_TYPE); |
| class = pci_read_config32(dev, PCI_CLASS_REVISION); |
| |
| /* Store the interesting information in the device structure */ |
| dev->vendor = id & 0xffff; |
| dev->device = (id >> 16) & 0xffff; |
| dev->hdr_type = hdr_type; |
| /* class code, the upper 3 bytes of PCI_CLASS_REVISION */ |
| dev->class = class >> 8; |
| |
| /* Architectural/System devices always need to |
| * be bus masters. |
| */ |
| if ((dev->class >> 16) == PCI_BASE_CLASS_SYSTEM) { |
| dev->command |= PCI_COMMAND_MASTER; |
| } |
| |
| /* Look at the vendor and device id, or at least the |
| * header type and class and figure out which set of |
| * configuration methods to use. Unless we already |
| * have some pci ops. |
| */ |
| set_pci_ops(dev); |
| /* Error if we don't have some pci operations for it */ |
| if (!dev->ops) { |
| printk_err("%s No device operations\n", |
| dev_path(dev)); |
| continue; |
| } |
| |
| /* Now run the magic enable/disable sequence for the device */ |
| if (dev->ops && dev->ops->enable) { |
| dev->ops->enable(dev); |
| } |
| |
| printk_debug("%s [%04x/%04x] %s\n", |
| dev_path(dev), |
| dev->vendor, dev->device, |
| dev->enabled?"enabled": "disabled"); |
| |
| if (PCI_FUNC(devfn) == 0x00 && (hdr_type & 0x80) != 0x80) { |
| /* if this is not a multi function device, |
| * don't waste time probing another function. |
| * Skip to next device. |
| */ |
| devfn += 0x07; |
| } |
| } |
| post_code(0x25); |
| |
| /* For all children that implement scan_bus (i.e. bridges) |
| * scan the bus behind that child. |
| */ |
| for (child = bus->children; child; child = child->sibling) { |
| if (!child->enabled || |
| !child->ops || |
| !child->ops->scan_bus) |
| { |
| continue; |
| } |
| max = child->ops->scan_bus(child, max); |
| } |
| |
| /* |
| * We've scanned the bus and so we know all about what's on |
| * the other side of any bridges that may be on this bus plus |
| * any devices. |
| * |
| * Return how far we've got finding sub-buses. |
| */ |
| printk_debug("PCI: pci_scan_bus returning with max=%02x\n", max); |
| post_code(0x55); |
| return max; |
| } |
| |
| /** |
| * @brief Scan a PCI bridge and the buses behind the bridge. |
| * |
| * Determine the existence of buses behind the bridge. Set up the bridge |
| * according to the result of the scan. |
| * |
| * This function is the default scan_bus() method for PCI bridge devices. |
| * |
| * @param dev pointer to the bridge device |
| * @param max the highest bus number assgined up to now |
| * |
| * @return The maximum bus number found, after scanning all subordinate busses |
| */ |
| unsigned int pci_scan_bridge(struct device *dev, unsigned int max) |
| { |
| struct bus *bus; |
| uint32_t buses; |
| uint16_t cr; |
| |
| printk_spew("%s for %s\n", __func__, dev_path(dev)); |
| |
| bus = &dev->link[0]; |
| bus->dev = dev; |
| dev->links = 1; |
| |
| /* Set up the primary, secondary and subordinate bus numbers. We have |
| * no idea how many buses are behind this bridge yet, so we set the |
| * subordinate bus number to 0xff for the moment. |
| */ |
| bus->secondary = ++max; |
| bus->subordinate = 0xff; |
| |
| /* Clear all status bits and turn off memory, I/O and master enables. */ |
| cr = pci_read_config16(dev, PCI_COMMAND); |
| pci_write_config16(dev, PCI_COMMAND, 0x0000); |
| pci_write_config16(dev, PCI_STATUS, 0xffff); |
| |
| /* |
| * Read the existing primary/secondary/subordinate bus |
| * number configuration. |
| */ |
| buses = pci_read_config32(dev, PCI_PRIMARY_BUS); |
| |
| /* Configure the bus numbers for this bridge: the configuration |
| * transactions will not be propagated by the bridge if it is not |
| * correctly configured. |
| */ |
| buses &= 0xff000000; |
| buses |= (((unsigned int) (dev->bus->secondary) << 0) | |
| ((unsigned int) (bus->secondary) << 8) | |
| ((unsigned int) (bus->subordinate) << 16)); |
| pci_write_config32(dev, PCI_PRIMARY_BUS, buses); |
| |
| /* Now we can scan all subordinate buses |
| * i.e. the bus behind the bridge. |
| */ |
| max = pci_scan_bus(bus, 0x00, 0xff, max); |
| |
| /* We know the number of buses behind this bridge. Set the subordinate |
| * bus number to its real value. |
| */ |
| bus->subordinate = max; |
| buses = (buses & 0xff00ffff) | |
| ((unsigned int) (bus->subordinate) << 16); |
| pci_write_config32(dev, PCI_PRIMARY_BUS, buses); |
| pci_write_config16(dev, PCI_COMMAND, cr); |
| |
| printk_spew("%s returns max %d\n", __func__, max); |
| return max; |
| } |
| |
| /* |
| Tell the EISA int controller this int must be level triggered |
| THIS IS A KLUDGE -- sorry, this needs to get cleaned up. |
| */ |
| static void pci_level_irq(unsigned char intNum) |
| { |
| unsigned short intBits = inb(0x4d0) | (((unsigned) inb(0x4d1)) << 8); |
| |
| printk_spew("%s: current ints are 0x%x\n", __func__, intBits); |
| intBits |= (1 << intNum); |
| |
| printk_spew("%s: try to set ints 0x%x\n", __func__, intBits); |
| |
| // Write new values |
| outb((unsigned char) intBits, 0x4d0); |
| outb((unsigned char) (intBits >> 8), 0x4d1); |
| |
| /* this seems like an error but is not ... */ |
| #if 1 |
| if (inb(0x4d0) != (intBits & 0xf)) { |
| printk_err("%s: lower order bits are wrong: want 0x%x, got 0x%x\n", |
| __func__, intBits &0xf, inb(0x4d0)); |
| } |
| if (inb(0x4d1) != ((intBits >> 8) & 0xf)) { |
| printk_err("%s: lower order bits are wrong: want 0x%x, got 0x%x\n", |
| __func__, (intBits>>8) &0xf, inb(0x4d1)); |
| } |
| #endif |
| } |
| |
| /* |
| This function assigns IRQs for all functions contained within |
| the indicated device address. If the device does not exist or does |
| not require interrupts then this function has no effect. |
| |
| This function should be called for each PCI slot in your system. |
| |
| pIntAtoD is an array of IRQ #s that are assigned to PINTA through PINTD of |
| this slot. |
| The particular irq #s that are passed in depend on the routing inside |
| your southbridge and on your motherboard. |
| |
| -kevinh@ispiri.com |
| */ |
| void pci_assign_irqs(unsigned bus, unsigned slot, const unsigned char pIntAtoD[4]) |
| { |
| unsigned functNum; |
| device_t pdev; |
| unsigned char line; |
| unsigned char irq; |
| unsigned char readback; |
| |
| /* Each slot may contain up to eight functions */ |
| for (functNum = 0; functNum < 8; functNum++) { |
| pdev = dev_find_slot(bus, (slot << 3) + functNum); |
| |
| if (pdev) { |
| line = pci_read_config8(pdev, PCI_INTERRUPT_PIN); |
| |
| // PCI spec says all other values are reserved |
| if ((line >= 1) && (line <= 4)) { |
| irq = pIntAtoD[line - 1]; |
| |
| printk_debug("Assigning IRQ %d to %d:%x.%d\n", \ |
| irq, bus, slot, functNum); |
| |
| pci_write_config8(pdev, PCI_INTERRUPT_LINE,\ |
| pIntAtoD[line - 1]); |
| |
| readback = pci_read_config8(pdev, PCI_INTERRUPT_LINE); |
| printk_debug(" Readback = %d\n", readback); |
| |
| // Change to level triggered |
| pci_level_irq(pIntAtoD[line - 1]); |
| } |
| } |
| } |
| } |