| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| chip soc/intel/tigerlake |
| # BitMask where bits [3:0] are Controller 0 Channel [3:0] and |
| # bits [7:4] are Controller 1 Channel [3:0]. |
| # Enable Command Mirroring for controller 0 channel 0 and 1, |
| # and controller 1 channel 0 and 1. |
| register "CmdMirror" = "0x00000033" |
| |
| register "DdiPort1Hpd" = "0" |
| register "DdiPort2Hpd" = "0" |
| |
| # Disable SRCCLKREQ1# |
| register "PcieClkSrcUsage[1]" = "PCIE_CLK_NOTUSED" |
| |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Audio | |
| #| I2C1 | Touchscreen | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| device domain 0 on |
| device ref dptf on |
| chip drivers/intel/dptf |
| ## Disable Active Policy |
| register "policies.active" = "{[0] = {.target=DPTF_NONE}}" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 52, 10000), |
| [1] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_0, 58, 30000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 53, 10000)}" |
| |
| ## Power Limits Control |
| # 7-9W PL1 in 200mW increments, avg over 28-32s interval |
| # PL2 is fixed at 40W, avg over 28-32s interval |
| register "controls.power_limits" = "{ |
| .pl1 = {.min_power = 7000, |
| .max_power = 9000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200,}, |
| .pl2 = {.min_power = 40000, |
| .max_power = 40000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}}" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 40, 2500 }, |
| [1] = { 30, 1900 }, |
| [2] = { 24, 1500 }, |
| [3] = { 16, 1000 }}" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{[0] = {0}}" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "0" |
| register "options.fan.step_size" = "0" |
| |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| # register "hid" is set in variants.c because of FW_CONFIG |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_R5)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a alias audio_codec on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "0" |
| register "imon_slot_no" = "1" |
| register "uid" = "0" |
| register "desc" = ""Right Speaker Amp"" |
| register "name" = ""MAXR"" |
| device i2c 31 on |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "2" |
| register "imon_slot_no" = "3" |
| register "uid" = "1" |
| register "desc" = ""Left Speaker Amp"" |
| register "name" = ""MAXL"" |
| device i2c 32 on |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_F16)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| # GPP_E17 is the IRQ source, and GPP_E1 is the wake source |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_HIGH(GPP_E17)" |
| register "key.wake_gpe" = "GPE0_DW2_01" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "detect" = "1" |
| device i2c 15 on |
| probe TOUCHPAD REGULAR_TOUCHPAD |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2702"" |
| register "generic.desc" = ""ELAN Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "generic.wake" = "GPE0_DW2_15" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on |
| probe TOUCHPAD NUMPAD_TOUCHPAD |
| end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref hda on |
| probe AUDIO MAX98357_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682_SNDW |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| probe AUDIO MAX98360_ALC5682I_I2S |
| probe AUDIO RT1011_ALC5682I_I2S |
| end |
| device ref pcie_rp9 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "srcclk_pin" = "0" |
| device generic 0 on end |
| end |
| end |
| device ref pmc hidden |
| # The pmc_mux chip driver is a placeholder for the |
| # PMC.MUX device in the ACPI hierarchy. |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port5 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref north_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(4, 2)" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 2)" |
| device ref tcss_usb3_port2 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| end |
| end |
| end |
| device ref south_xhci on |
| register "usb2_ports" = "{ |
| [0] = USB2_PORT_TYPE_C(OC1), // Type-A Port A0 |
| [1] = USB2_PORT_TYPE_C(OC2), // Type-A Port A1 |
| [2] = USB2_PORT_TYPE_C(OC0), // Type-C Port C1 |
| [3] = USB2_PORT_MID(OC_SKIP), // Front Camera |
| [4] = USB2_PORT_TYPE_C(OC3), // Type-C Port C0 |
| [5] = USB2_PORT_MID(OC_SKIP), // WFC Camera |
| }" |
| |
| register "usb3_ports" = "{ |
| [0] = USB3_PORT_DEFAULT(OC1), // USB3/2 Type-A Port A0 |
| [1] = USB3_PORT_DEFAULT(OC2), // USB3/2 Type-A Port A1 |
| }" |
| |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port2 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb2_port3 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(4, 1)" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""WFC Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref usb3_port2 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| end |
| end |
| end |
| end |
| end |