| config SOC_INTEL_TIGERLAKE |
| bool |
| help |
| Intel Tigerlake support |
| |
| if SOC_INTEL_TIGERLAKE |
| |
| config CPU_SPECIFIC_OPTIONS |
| def_bool y |
| select ACPI_INTEL_HARDWARE_SLEEP_VALUES |
| select ARCH_BOOTBLOCK_X86_32 |
| select ARCH_RAMSTAGE_X86_32 |
| select ARCH_ROMSTAGE_X86_32 |
| select ARCH_VERSTAGE_X86_32 |
| select BOOT_DEVICE_SPI_FLASH_RW_NOMMAP_EARLY if BOOT_DEVICE_SPI_FLASH |
| select BOOT_DEVICE_SUPPORTS_WRITES |
| select CACHE_MRC_SETTINGS |
| select CPU_INTEL_COMMON |
| select CPU_INTEL_FIRMWARE_INTERFACE_TABLE |
| select FSP_COMPRESS_FSP_S_LZ4 |
| select FSP_M_XIP |
| select GENERIC_GPIO_LIB |
| select HAVE_FSP_GOP |
| select INTEL_DESCRIPTOR_MODE_CAPABLE |
| select HAVE_SMI_HANDLER |
| select IDT_IN_EVERY_STAGE |
| select INTEL_CAR_NEM #TODO - Enable INTEL_CAR_NEM_ENHANCED |
| select INTEL_GMA_ACPI |
| select INTEL_GMA_ADD_VBT if RUN_FSP_GOP |
| select IOAPIC |
| select MRC_SETTINGS_PROTECT |
| select PARALLEL_MP |
| select PARALLEL_MP_AP_WORK |
| select MICROCODE_BLOB_UNDISCLOSED |
| select PLATFORM_USES_FSP2_2 |
| select FSP_PEIM_TO_PEIM_INTERFACE |
| select REG_SCRIPT |
| select SMP |
| select PMC_GLOBAL_RESET_ENABLE_LOCK |
| select CPU_INTEL_COMMON_SMM |
| select SOC_INTEL_COMMON |
| select SOC_INTEL_COMMON_ACPI_WAKE_SOURCE |
| select SOC_INTEL_COMMON_BLOCK |
| select SOC_INTEL_COMMON_BLOCK_ACPI |
| select SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG |
| select SOC_INTEL_COMMON_BLOCK_CPU |
| select SOC_INTEL_COMMON_BLOCK_CPU_MPINIT |
| select SOC_INTEL_COMMON_BLOCK_DTT |
| select SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT |
| select SOC_INTEL_COMMON_BLOCK_GSPI_VERSION_2 |
| select SOC_INTEL_COMMON_BLOCK_HDA |
| select SOC_INTEL_COMMON_BLOCK_SA |
| select SOC_INTEL_COMMON_BLOCK_SMM |
| select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP |
| select SOC_INTEL_COMMON_PCH_BASE |
| select SOC_INTEL_COMMON_RESET |
| select SOC_INTEL_COMMON_BLOCK_CAR |
| select SOC_INTEL_COMMON_BLOCK_POWER_LIMIT |
| select SSE2 |
| select SUPPORT_CPU_UCODE_IN_CBFS |
| select TSC_MONOTONIC_TIMER |
| select UDELAY_TSC |
| select UDK_2017_BINDING |
| select DISPLAY_FSP_VERSION_INFO |
| select HECI_DISABLE_USING_SMM |
| |
| config DCACHE_RAM_BASE |
| default 0xfef00000 |
| |
| config DCACHE_RAM_SIZE |
| default 0x80000 |
| help |
| The size of the cache-as-ram region required during bootblock |
| and/or romstage. |
| |
| config DCACHE_BSP_STACK_SIZE |
| hex |
| default 0x40400 |
| help |
| The amount of anticipated stack usage in CAR by bootblock and |
| other stages. In the case of FSP_USES_CB_STACK default value will be |
| sum of FSP-M stack requirement(256KiB) and CB romstage stack requirement |
| (~1KiB). |
| |
| config FSP_TEMP_RAM_SIZE |
| hex |
| default 0x20000 |
| help |
| The amount of anticipated heap usage in CAR by FSP. |
| Refer to Platform FSP integration guide document to know |
| the exact FSP requirement for Heap setup. |
| |
| config IFD_CHIPSET |
| string |
| default "tgl" |
| |
| config IED_REGION_SIZE |
| hex |
| default 0x400000 |
| |
| config HEAP_SIZE |
| hex |
| default 0x10000 |
| |
| config MAX_ROOT_PORTS |
| int |
| default 12 |
| |
| config MAX_PCIE_CLOCKS |
| int |
| default 7 |
| |
| config SMM_TSEG_SIZE |
| hex |
| default 0x800000 |
| |
| config SMM_RESERVED_SIZE |
| hex |
| default 0x200000 |
| |
| config PCR_BASE_ADDRESS |
| hex |
| default 0xfd000000 |
| help |
| This option allows you to select MMIO Base Address of sideband bus. |
| |
| config MMCONF_BASE_ADDRESS |
| hex |
| default 0xc0000000 |
| |
| config CPU_BCLK_MHZ |
| int |
| default 100 |
| |
| config SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ |
| int |
| default 120 |
| |
| config DRIVERS_I2C_DESIGNWARE_CLOCK_MHZ |
| int |
| default 133 |
| |
| config SOC_INTEL_COMMON_BLOCK_GSPI_MAX |
| int |
| default 4 |
| |
| config SOC_INTEL_I2C_DEV_MAX |
| int |
| default 6 |
| |
| config SOC_INTEL_UART_DEV_MAX |
| int |
| default 3 |
| |
| config CONSOLE_UART_BASE_ADDRESS |
| hex |
| default 0xfe032000 |
| depends on INTEL_LPSS_UART_FOR_CONSOLE |
| |
| # Clock divider parameters for 115200 baud rate |
| # Baudrate = (UART source clcok * M) /(N *16) |
| # TGL UART source clock: 120MHz |
| config SOC_INTEL_COMMON_LPSS_UART_CLK_M_VAL |
| hex |
| default 0x25a |
| |
| config SOC_INTEL_COMMON_LPSS_UART_CLK_N_VAL |
| hex |
| default 0x7fff |
| |
| config CHROMEOS |
| select CHROMEOS_RAMOOPS_DYNAMIC |
| |
| config VBOOT |
| select VBOOT_SEPARATE_VERSTAGE |
| select VBOOT_MUST_REQUEST_DISPLAY |
| select VBOOT_STARTS_IN_BOOTBLOCK |
| select VBOOT_VBNV_CMOS |
| select VBOOT_VBNV_CMOS_BACKUP_TO_FLASH |
| |
| config C_ENV_BOOTBLOCK_SIZE |
| hex |
| default 0xC000 |
| |
| config CBFS_SIZE |
| hex |
| default 0x200000 |
| |
| config FSP_HEADER_PATH |
| default "src/vendorcode/intel/fsp/fsp2_0/tigerlake/" |
| |
| config FSP_FD_PATH |
| default "3rdparty/fsp/TigerLakeFspBinPkg/Fsp.fd" |
| |
| config SOC_INTEL_TIGERLAKE_DEBUG_CONSENT |
| int "Debug Consent for TGL" |
| # USB DBC is more common for developers so make this default to 3 if |
| # SOC_INTEL_DEBUG_CONSENT=y |
| default 3 if SOC_INTEL_DEBUG_CONSENT |
| default 0 |
| help |
| This is to control debug interface on SOC. |
| Setting non-zero value will allow to use DBC or DCI to debug SOC. |
| PlatformDebugConsent in FspmUpd.h has the details. |
| |
| Desired platform debug type are |
| 0:Disabled, 1:Enabled (DCI OOB+[DbC]), 2:Enabled (DCI OOB), |
| 3:Enabled (USB3 DbC), 4:Enabled (XDP/MIPI60), 5:Enabled (USB2 DbC), |
| 6:Enable (2-wire DCI OOB), 7:Manual |
| |
| config PRERAM_CBMEM_CONSOLE_SIZE |
| hex |
| default 0xe00 |
| endif |