| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| # Disable PCIe Root Port 8 (index 7) |
| register "PcieRpEnable[7]" = "0" |
| # Disable PCIe Clock Source 4 (index 3) |
| register "PcieClkSrcUsage[3]" = "0xff" |
| |
| # USB Port Configuration |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # User Facing Camera |
| register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/1 Type-A Port A1 |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | Digitizer, Stylus | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | Camera | |
| #| I2C4 | Audio | |
| #| I2C5 | P-Sensor | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 260, |
| .fall_time_ns = 50, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 86, |
| .fall_time_ns = 5, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 84, |
| .fall_time_ns = 4, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 69, |
| .fall_time_ns = 3, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 129, |
| .fall_time_ns = 4, |
| }, |
| }" |
| |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # WWAN |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| # Power limit config |
| register "power_limits_config[JSL_N4500_6W_CORE]" = "{ |
| .tdp_pl1_override = 7, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "power_limits_config[JSL_N6000_6W_CORE]" = "{ |
| .tdp_pl1_override = 7, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "power_limits_config[JSL_N5100_6W_CORE]" = "{ |
| .tdp_pl1_override = 7, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "tcc_offset" = "10" # TCC of 95C |
| |
| register "xhci_lfps_sampling_offtime_ms" = "0" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 67, 3000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 67, 3000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 67, 3000),}" |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 80, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN),}" |
| register "controls.power_limits.pl1" = "{ |
| .min_power = 3000, |
| .max_power = 7000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 125,}" |
| register "controls.power_limits.pl2" = "{ |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}" |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 32, 2000 }, |
| [2] = { 24, 1500 }, |
| [3] = { 16, 1000 }, |
| [4] = { 8, 500 } |
| }" |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 05.0 on # IPU - MIPI Camera |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "2" |
| register "cio2_lanes_used" = "{1,4}" |
| register "cio2_lane_endpoint[1]" = ""^I2C3.CAM1"" |
| register "cio2_prt[0]" = "0" |
| register "cio2_prt[1]" = "2" |
| device generic 0 on end |
| end |
| end |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""User Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D15)" |
| register "enable_delay_ms" = "20" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)" |
| register "reset_off_delay_ms" = "10" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" |
| register "enable_delay_ms" = "20" |
| device usb 3.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.4 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end #I2C 0 |
| device pci 15.2 on |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_C12)" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "7" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end # I2C 2 |
| device pci 15.3 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM1"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "4" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "360000000" |
| register "link_freq[1]" = "180000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D13" #power_enable_2p8 |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D14" #power_enable_1p2 |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D12" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C3.CAM1.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0c on end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on end |
| end |
| end # I2C 3 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| end # I2C 4 |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| device pci 19.1 on |
| chip drivers/i2c/sx9324 |
| register "desc" = ""SAR Proximity Sensor"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E11_IRQ)" |
| register "uid" = "2" |
| register "reg_gnrl_ctrl0" = "0x0a" |
| register "reg_gnrl_ctrl1" = "0x22" |
| register "reg_afe_ctrl0" = "0x20" |
| register "reg_afe_ctrl3" = "0x00" |
| register "reg_afe_ctrl4" = "0x47" |
| register "reg_afe_ctrl6" = "0x00" |
| register "reg_afe_ctrl7" = "0x47" |
| register "reg_afe_ctrl8" = "0x12" |
| register "reg_afe_ctrl9" = "0x08" |
| register "reg_afe_ph0" = "0x37" |
| #register "reg_afe_ph1" = "0x10" |
| register "reg_afe_ph1" = "0x37" |
| register "reg_afe_ph2" = "0x1f" |
| register "reg_afe_ph3" = "0x3d" |
| register "reg_prox_ctrl0" = "0x0b" |
| register "reg_prox_ctrl1" = "0x0b" |
| register "reg_prox_ctrl2" = "0x20" |
| register "reg_prox_ctrl3" = "0x20" |
| register "reg_prox_ctrl4" = "0x0c" |
| register "reg_prox_ctrl5" = "0x00" |
| register "reg_prox_ctrl6" = "0x1c" |
| register "reg_prox_ctrl7" = "0xc0" |
| register "reg_adv_ctrl0" = "0x00" |
| register "reg_adv_ctrl1" = "0x00" |
| register "reg_adv_ctrl2" = "0x00" |
| register "reg_adv_ctrl3" = "0x00" |
| register "reg_adv_ctrl4" = "0x00" |
| register "reg_adv_ctrl5" = "0x05" |
| register "reg_adv_ctrl6" = "0x00" |
| register "reg_adv_ctrl7" = "0x00" |
| register "reg_adv_ctrl8" = "0x00" |
| register "reg_adv_ctrl9" = "0x00" |
| register "reg_adv_ctrl10" = "0x00" |
| register "reg_adv_ctrl11" = "0x00" |
| register "reg_adv_ctrl12" = "0x00" |
| register "reg_adv_ctrl13" = "0x00" |
| register "reg_adv_ctrl14" = "0x80" |
| register "reg_adv_ctrl15" = "0x0c" |
| register "reg_adv_ctrl16" = "0x04" |
| register "reg_adv_ctrl17" = "0x70" |
| register "reg_adv_ctrl18" = "0x20" |
| register "reg_adv_ctrl19" = "0x00" |
| register "reg_adv_ctrl20" = "0x00" |
| register "reg_irq_cfg0" = "0x00" |
| register "reg_irq_cfg1" = "0x80" |
| register "reg_irq_cfg2" = "0x01" |
| device i2c 28 on end |
| end |
| end # I2C 5 |
| end |
| end |